How To Replace The Front Hub Bearing On A 2008 Infiniti FX35

Here are some of the tools that jimthecarguy uses
www.amazon.com/shop/jimthecarguy
How to replace the front hub bearing, brakes and rotors on a 2008 Infiniti FX35.I will show you step by step how to replace the hub bearing assembly.Also I will sow you some precautions you will need to take before you start the job.
Due to factors beyond the control of jimthecarguy, it cannot guarantee against unauthorized modifications of this information,. jimthecarguy assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. jimthecarguy recommends safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, chemicals, or any other tools or equipment seen or implied in this video. Due to factors beyond the control of jimthecarguy, no information contained in this video shall create any express or implied warranty or guarantee of any particular result. Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained in this video is the sole responsibility of the user and not jimthecarguy.

[@SEXYCOBRAS]

Great step by step. Thank you so much. I feel comfortable doing the front hubs on my G35X now!

[@craigvinson8208]

Thank you so much for doing this video. I wasn't looking forward to a lot of disassembly to get the hubs off, and you showed me it's possible to do without too much work.

[@geraldsun6812]

I have 2010 FX35 and just replaced mine today without a hitch. Thank you for this video it really helps.

[@jimthecarguy]

Gerald Sun Thank you for watching the video. Great job!

[@Buddy8431]

This video saved a bank load of money!! Thank you very much for a very detailed and informative "How To" video.

[@gogilgau]

Very good video, Thank you, Your a natural presenter,,, love the preview, step by step explanation and the final review.... Good lighting, good sound!,,, Awesome, Thank you! Now i will use this to work on my Infiniti G37X car, all looks identical!

[@FyukYiu]

Thank you. Going to work on my wife’s Infiniti and this was a good video!

[@bobbymathis1700]

The video production and narration are perfect. And, you can tell Jim is a guy with a lot of integrity. Wish he was in our town, he'd get my business. Well done! I have a 2007 G35x with what sounds like a wheel hub issue (new tires did not correct what sounded like tires singing). This video may have given me the confidence to try this myself. Hopefully, the 32mm nut will come off using a breaker bar.

[@jimthecarguy]

Thank you for watching . Don't forget to subscribe.

[@spadds]

Spot on Jim, nice job. Thanks for the posting.

[@lefty5595]

Great video! I replaced both front hubs in my wife’s Fx35.....about 6 month between jobs. I watched your video before each job. Watching you reminds me of the countless times I watched my dad repair cars.......I think you might be more patient 😳

[@dendrobialbright7616]

Good video, and great instruction! Thank you do much! I gotta replace bearing hubs this weekend. This has greatly helped!

[@jimthecarguy]

+Dendrobial Bright Thank you for watching and your feedback

[@ednaldocampos]

Great video and I like to see how you work carefully. Thank you. I am just sad because I have G37 2012.

[@cynthiaingram3597]

Where were you when I was living in Jersey....LOL...You sir are a rare Mechanic "GEM"....Great great and awesome video...Now I need to have my Front right side did...But I rather do both bearing than the one that's bad...Thank you sir,again great video...You definitely made it look easy!

[@Carlostype]

HD Jim, nice! If you get a stubborn bearing that wants to fight to the death please film it , Eric O has had some awesome battles on film, and we get to see how you overcome their removal, cheers

[@jimthecarguy]

+Typey1 I will keep that in mind for the next one and I'm sure there will be a next one.Lol

[@gort400]

Your videos are AWESOME! Thank you

[@bobbymathis1700]

I did this repair today on a 2007 Infiniti G35x. It took about 6 hours including set up and clean up. Just a few 1/2' tools that helped make the job easier for me: - 1. 25" breaker bar (Harbor Freight). - 32mm deep socket. - 22mm socket. - 17mm socket. - 1/2" socket extensions (short & med length). Also: - 3lb hammer. - 14mm box wrench/ratchet. - anti-seize paste. - wire brush. - sand paper. - prybar. - worklight. - floor jack. - jack stands. The replacement wheel hub I received did not align with the ABS sensor. This required repositioning the backplate of the hub. I was able to do this using the pipe jaws of a 5" bench vice (and using a screw driver & hammer to rotate the backplate). If I didn't have the vice, I'm not sure this would have been achieved. Jim's video deserves all the credit for a good outcome. What I thought was bad tires turned out to be a roaring driver side wheel hub.

[@jimthecarguy]

Bobby thank you for adding the list of tools needed.

[@jasonpope1265]

Thanks for this video. Getting ready to do my 06 Fx35

[@502Loco]

AWESOME AWEEEESOME tutorial!! Thank you very much sir, you are a true teacher. Much respect!🖒🖒

[@jimthecarguy]

502Loco Thank you for watching and for your input

[@craigtaylor9764]

Just watched this awesome video. Very informative and easy to follow. Thank you!

[@jimthecarguy]

I'm happy to help. Thanks for watching.

[@syedhussain3810]

hey man you are a great help. Thanks for your precious time

[@tyjonpoole1056]

I totally agree great step by step 👍🏽we appreciate you Sir

[@djjjamz]

Another good video. You make it look so easy

[@jimthecarguy]

+Jimmy G Thank you for your feedback and for watching

[@danielsaunders829]

Nice video Jim! They are all so clear and helpful. About to embark on a similar project. (Maybe my ABS tone ring is bad?). Details: My 2006 Nissan Murano has ABS and AWD error lights on, and a really bad front brake pulsation - but only for the first few seconds of driving. Computer showed a bad right front ABS signal so I replaced that ABS sensor and cleaned the other 3. I also did all 4 brakes very carefully, with all new slide pins, clips, rubber boots... lubed everything, torqued everything (incl lug nuts) to spec... and still have the same exact pulsation. Then, took apart right front brakes again, checked/lubed parts, replaced rotor this time, sanded the brand new pads a bit (but they seemed perfect)... and the really bad pulsation continues for only the first few seconds of driving. ABS and AWD error lights are still on. Think it's a bad ABS control module or tone ring? What a pain in the @$%&! Dan

[@billlincoln6087]

Fantastic video. Great tutorial.

[@jimthecarguy]

I'm happy to help.Thanks for watching and your input

[@gregpratt6926]

Nice job with step by step. I wonder if you really want the customer to replace the wheel bgr on the other side also? Would have made a complete Job. Thank you for the good information.

[@rickcamp629]

well done and helpful. would you expect if the left side needs replacement that you should also replace the right? how much does this service cost if we chicken out on DIY?

[@bpg1622]

Nice video ! Clear and concise. I have to do an infinity q37. Any differences to be aware in comparison to the q35?

[@ryd137]

awesome video quick question did you take off the brake fluid cap on the reservoir doing the brake job? thanks much. also is it good to change both front bearings left and right? at same time

[@xxrodneyxx]

Great vid. Thank you.

[@jimthecarguy]

+Rodney C Thank you for your feedback

[@uccoskun]

Hello, thank you for clear instructions. I have two questions if you have time: 1. Did you do any trick to remove ABS sensor after the first attempt? 2. Do you think we should use tread lock on Caliper bracket bolts?

[@kansasgardener5844]

I can answer that. If you don't break the bolt on the sensor you can twist it to get it out. It's round! No loctite on any of the bolts but do torque to spec!

[@kevinstanard3696]

Thank you very much , great job

[@jimthecarguy]

+Kevin Stanard Happy to help.Thanks for watching

[@sz8204]

Thanks ur video helped a lot!

[@jimthecarguy]

Syed Danish Zaidi Glad to hear, thanks for watching!

[@SteveRobReviews]

Well done buddy.

[@jimthecarguy]

+Steve Rob Thank you Steve

[@henrietn]

great video!

[@jimthecarguy]

+Hendrik Derudder Thank you for watching and your feedback

[@darklitimijre2059]

What is the ring that the ABS sensor is in. @12:01 I damage my last sensor, got a new one and realized I also damage the ring in there that the sensor holds in place. I bought a new wheel hub and it did not come with that ring so I assume you can buy just that part.

[@normansmith7806]

Good video!

[@jimthecarguy]

+N Smith Thank you

[@mikeharris3352]

Great video and you sound like a NewYorker

[@jimthecarguy]

Mike Harris LOL, born and raised in New Jersey.

[@mhoff7722]

Great job! I don't know how you got that ABS sensor out. Mine was so stuck in that mounting hole I had to drill it out and replace it. I also had to cut the ABS sensor slot in the back of the bearing hub to make it bigger in order to fit the tip of the sensor in it. All parts were "exact fit"... Go figure.

[@gort400]

Jim, I have a question about replacing the valve cover gaskets on my 1995 Infinity Q45. I don't have your email so I hope its ok to ask here. Oil is leaking down on the exhaust manifolds, both sides and smoking. Do you have any links to how to replace these gaskets. It almost looks like you have to take the whole top of the engine off just to get at them. Any suggestions appreciated. Thank You.

[@ManicMechanic007]

Nice camera, great detail. Keep up the good work Jim.

[@jimthecarguy]

+ManicMechanic007 Thank you for noticing the new camera.

[@theaverage7550]

I was wondering, before I put the new hub bearing on, should I clean or grease the drive shaft splines? Thanks

[@mannysmobileautodetail]

I just order for my infiniti. I ask some mechanics for how mush the will fix it. Let me told you that it is expensive. its over 300 dls to fix it. But thanks to you 😀 I can do it my self 😁👍 Thank you so much 💪

[@jimthecarguy]

Great .I'm happy to help.Thank you for watching . Don't forget to subscribe.

[@jameshollis9062]

@jimthecsrguy:I just replaced my front hub bearing on a 2009 Infinity M35X. I did not take the wheel sensor off now my ABS,AWD,SLIP and VDC lights are on I think I sheared the sensor off, can I just replace the sensor or do I have to do the whole procedure over again?

[@shanesmith993]

How did it work out for you?

[@twinkieymythy]

Do you have to grease anything for the wheel hub?

[@darrenheaden3119]

Question, I need bearings replaced on one side should I replace the other side as well? Thank you in advance. Butches way. Nice video. I feel I can do this job myself. Great job

[@jimthecarguy]

I do a live stream on Sunday nights at 7:00 PM (EST) I will talk about this tonight .I hope you can stop by.Jim

[@marcusmarmolejos6530]

hi jim.. thanks for the video.. Im having an issue now with my abs sensor after i changed the bearing. on the drivers side. i actually ordered a new sensor and for some reason its not reading on that one side i had it scanned at 2 different garages and it keeps coming back to that side.. I put 2 new sensors on and nothing. someone told me i should change the wheel bearing. have you ever run into this issue.

[@deltabravo5719]

sounds to me like you put in a wheel bearing without the ABS MAGNETS INSIDE. there are non and abs wheel bearings that fit most cars. Yes, its likely you will need to get the correct ABS wheel bearing for your car. good luck.

[@evocre8r]

Excellent video. Thanks so much. Looks like something I can do in a garage. Would you recommend changing both sides even though only one is broken? Thanks

[@jimthecarguy]

I always leave it up to the owner but I would replace both on my own car.Some times the noise sounds like the one side but after replacing the really bad one you can now hear the other side.

[@deltabravo5719]

Id would like to weigh in... Yes, replace both sides... if one is gone, they other is on edge of going bad... likely.... its making noise that is just lower pitch than the louder/bad bearing. no they dont both have to be done in the same day... if you dont have time... put it off till you are ready... just expect the second bearing to go when the first does... they make anywhere from 50K to 150K miles.. my infinity G37X made 70K for the pass side and i put the drivers side on the shelf.. it made it to 125K. I been running the car for 5K with bearing howl... they last a long time when going bad. Thank you safety engineers. and bearing design today. LOL

[@blazarchzagnatz7506]

Before pushing in the brake pistons, draw off some brake fluid from the master cylinder. After completing the job, make sure you pump the brake pedal. It might get exciting not having brakes for a while. Be careful to top off the fluid during the pumping phase. These are just suggestions, your mileage will vary.

[@aycould7385]

thanks for the great vid, wodering what will be different for the rear bearings? (If there is any)

[@macdurden412]

Maybe suspension parts, being it is the rear end. Should be similiar

[@macdurden412]

Two years later lol my bad

[@GuNNeR2SicK]

I have a 2007 infiniti m45 sport ...I bought 2 new rotors for the front and breaks but one seem to wobble as I turn it with my hands I bolt on the rotors I spun them around and one wobbles what do you think it might be ...thanks Jim

[@jimthecarguy]

You will need to check the hub where the rotor goes on for rust.If it is rusted you will need to clean it off.If there is no rust then you have a defective rotor and will need to replace it.Keep me posted.

[@SouthMainAuto]

Nice camera Jim but come on man we need some drama! Lets get that phone ringing off the hook, customers stopping in your wife coming out to bug ya and for gosh sakes man get some rust! That thing was like a brand new car :) Haha great job Jim, looking good man!

[@jimthecarguy]

+South Main Auto Repair Thank you Eric.All this time I've been editing out that stuff .Lol Rust no thanks you have enough of that for both of us.Hope your ready for the snow I see its headed your way.Luck you:-)

[@davecaselli1957]

+South Main Auto Repair Funny, because when Jim said" this car is quite rusty" I looked closer because I had just said to myself, "at least it's not really rusty."

[@jimthecarguy]

+Dave Caselli Your right the rust on my cars is nothing compared to what Eric O has to deal with .Lol

[@JoseFernandez-sb4im]

South Main Auto Repair great video thankyou

[@Colinc9937]

great video i have to replace same thing on my 05 fx. thanks for the help i hope the abs bolt doesn't break on me

[@jimthecarguy]

+colin chavanic That will be the worst part of the job.Be careful with them.If you need any advice let me know.

[@rickcamp629]

would you expect if the left side needs replacement that you should also replace the right? how much does this service cost if we chicken out on DIY?

[@jimthecarguy]

No you could just replace the side thats bad.Cost should be around 5-6 hundred depending on the cost of the bearing.

[@rickcamp629]

Thanks

[@nathangauthier3901]

Great video. I just replaced mine using your tutorial, but now all my warning lights are on. SLIP, ABS, VDC

[@jimthecarguy]

Were these lights on before you replaced the bearing?What brand bearing did you use?

[@mikeharris3352]

I'm a New York and I can hear it!

[@jimthecarguy]

Thank you for watching .Im from New jersey.

[@robertnicoletti3846]

The outer nut needs to be torqued to a specific ft/lb. No? After torquing to specific spec, you should back off a 1/4 turn. Is that not correct?

[@bobbytomlin532]

Hi that wire that plugs into the hub assembly is that the abs sensor?

[@geraldtek]

bobby tomlin yes it is

[@tyronemccoy3102]

As usual your presentation are excellent, one thing though. I didn't get the size of the axel nut.

[@jimthecarguy]

Tyrone McCoy thank for watching I'm happy to help

[@AngelRecendez23]

I am planning to do this same job.

[@stuzman52]

Hey Jim, very nice step-by-step on removing and installing a new hub. And I see that you got yourself that new HD camera. How are you liking it? And will you get caught in the big snowstorm? As for me here in NC, we're getting blasted with it now with sleet on top of snow. What a mess down here! Take care Jim and good work!

[@jimthecarguy]

+stuzman52 Hi Terry .I can't believe the difference with the new HD camera .I really like it.As for the snow yes it is on the way from you in NC to us in NJ.Thanks a lot.Lol

[@stuzman52]

The camera make a big difference in detail. Stay warm and safe up there with the snow. Take care Jim..

[@evocre8r]

+jimthecarguy Wow Jim, you're in NJ, eh? Any chance I can get you to work on my 08 G35x-S? Looking to get the wheel bearing replaced. Thanks, Scott

[@jimthecarguy]

Yes no problem .Let me know when and we can work it out.

[@ebrown782]

Do u recommend replacing the bearings in pairs or just the one that's bad? I like to go with the old saying.if it ain't broke don't fix it

[@sinergy100]

They don't need to be replaced in pairs.

[@geraldtek]

ellis brown I'm a repair tech but not for cars. One thing I do know that if there is a pair and one goes bad, then it may not be much longer before the other one goes bad as well......im changing both of my hub assemblies for the peace of mind

[@TheDisgruntledMechanic]

Good video Jim! I wish I would have left the ABS sensor in the last one I did. On mine I think I could have left it on. what a mess. The actual sensor came out in pieces.

[@bayviewautorepair]

+The Disgruntled Mechanic Ya some time if you don't remove the sensor the bearing when it is removed rips out the sensor.Do you know how I know that ? it also happen to me.Lol

[@jimthecarguy]

+The Disgruntled Mechanic Ya some time if you don't remove the sensor the bearing when it is removed rips out the sensor.Do you know how I know that ? it also happen to me .Lol

[@TheDisgruntledMechanic]

+jimthecarguy what the heck? Starting a new channel?

[@HoUsEoFcAtS78]

@@jimthecarguy did you end up breaking the bolt that holds the sensor in the hub? Or did the bolt actually come out clean?

[@KK10027]

Hi. Is it absolutely necessary to use torque wrench for replacing G35 rwd front wheelbearing?

[@jimthecarguy]

Yes that is very important.

[@thecarsectionthecarsection6420]

You know nissan and Infiniti well i will bring my car to you when im visiting ny

[@kingkante11]

where are you locate in NJ? I want you to do my 06 fx35 front wheel bearing.

[@jimthecarguy]

+Soufi Kailer My shop is in Bayonne.If you need to talk to me send me a private message with your phone number.

[@mazinyako7]

You shouldn't be using an impact wrench while tightening the axel nut "use a torque wrench".

[@Mtb-TrailTime]

was this an awd or rear drive?

[@davidpooran2526]

Is the axle nut a 32 mil ? Ive to do mine on a 07 g35x. Im assuming its similar. Just wanted to figure out everything ill need before i start it

[@danielgordon9926]

David Pooran did you use a 32mm? Socket

[@davidpooran2526]

@@danielgordon9926 yup it's a 32 mil deep. Saved 300 bucks in labour doing it myself.

[@danielgordon9926]

David Pooran that’s what’s up , I have an 08 g35 would the 32mm work for me ?

[@davidpooran2526]

@@danielgordon9926 yup 08 g35 is the same deal.

[@danielgordon9926]

David Pooran thanks bro

[@neworleansnative3448]

What size is the axle nut sir?

[@asam9498]

Hey, Jim do you think this vehicle is reliable?

[@danielgordon9926]

What socket did you use to remove the bolt on the rack n pinion ?

[@jimthecarguy]

Thanks for watching

[@michaelherbert8213]

Awesome video. New camera? Do you ever have to break out an oxy/acetylene torch?

[@jimthecarguy]

+Michael Herbert Hi Michael .Thank you for noticing about the camera.This is the first video with the new camera .I hope it is a big improvement.Jim

[@nicknicu1787]

+jimthecarguy Huge improvement! Well done! Thanks for the videos Jim!

[@jimthecarguy]

+Nick Nicu Thank you for noticing .I hope you enjoy my videos.

[@palopezneri]

Do you need a torque wrench for this ?

[@DanielShepherdjr]

Is this the same for a 12 infiniti m37x?

[@tonyfederico2466]

Would changing a 2008 Infiniti g35s sedan fwd bearing be similar?

[@tonyfederico2466]

Sorry im dumb RWD*

[@Colinc9937]

can u tell me what size socket for the front axle bolt 32mm?

[@jimthecarguy]

+colin chavanic Sorry I don't recall but 32mm may be it.

[@Episcleritis]

Do you prefer the OEM bearing or is there an aftermarket bearing you like for the Infiniti?

[@raoulwright4484]

Is it the same procedure for the 2008 Infiniti QX56

[@jimthecarguy]

Yes it should be the same procedure.Thank you for watching.

[@angelalewis3667]

Is it the same for doing a infinite q50 awd?

[@jimthecarguy]

Yes the procedure is almost the same. Thanks for watching .

[@lorddale2212]

2007 Infiniti FX35 AWD My brakes are weak/spongy This happened after I changed the FRONT wheel bearings. The brake lines show no signs of leakage. The system has completely flushed (bled) through all the brake lines until the new brake fluid was coming out the bleeders. (No old brake fluid in the system whatsoever) We bled the system for abt 6 hours thinking it was the issue. Brake fluid is cleaner than new Nikes. The Master Cylinder has been replaced New rotors have been put on all around New brake pads have been put on all around. No Brake light No Abs light No Check Engine Light Any ideas?

[@ryd137]

no torque specs tightening?

[@ImBatman83]

do the knowledge German torque specs. Good n tight. Lol. 😂

[@Future_memory]

How many mm for the axle nut ?

[@macelius]

Good vid. Torque specs anyone?

[@rexhole85]

110

[@bflowinstreamy9362]

Is it bolt on or press on

[@kcianderson001]

My infiniti fx35 2005 is not running properly what could possibly be the cause??

[@sz8204]

Just a word of caution for future diyers... DO NOT forget to install the dust/heat shield plate... it's very easy to forget installing it but a pain to put it back in as u will have to undo everything.

[@jimthecarguy]

Thank you for your input and for watching

[@Juice-jx1pr]

How much do you charge

[@packwoodperformance4x474]

I used this video to fix mine and to make my own video.

[@jimthecarguy]

Thanks for watching

[@packwoodperformance4x474]

Thank you. Best video I found.

[@theark1093]

Вот все бы так подробно и понятно снимали как это американский парень. Привет тебе из России).

[@xls4750]

Tourque specs ?

[@Juice-jx1pr]

Yes I am okay

[@pauljohn6546]

10:22, yes I’m okay. Thanks

[@jimthecarguy]

Hahaha

[@jerrybikejerry4672]

sir this my fourth time I sent message please I wanna purchase a fx35 infinite but the owner told me it had timing chain problem and another again gat transmission issues is ,2 jeep I wanna buy them repair and resell it again isn't repairable

[@richphero106]

I did this, although now I hear a screeching sound from where I worked on the car.

[@luisfigueroa2011]

rich phero Maybe that metal shield got bent during removal and installation.

[@jimthecarguy]

As Luis said check the shield.Thanks for watching.

[@jimthecarguy]

Thank you for your input. I would have said the same thing.Thanks for watching.

[@pitbullkngz7236]

You forgot the washer between the hub bearing and the hub nut or at least forgot the direction to reinstall it and that will cause premature bearing failure if forgotten

[@jimthecarguy]

You should watch the video a second time . Watch at 15:45 to see me install the washer along with the nut.

[@ItsClumsy]

Replaced my wheel bearing on the side of the road after the old one failed and the new one wasn’t tightened all the way so that is broken as well lol..

[@fieldsofomagh]

Tricky enough reassembly.

[@jimthecarguy]

+Tom OConnor thank you for watching

[@kansasgardener5844]

You forgot to torque the bolts and axle nut to spec!

[@LUISGONZALEZ-jy3wq]

Any idea what the torque specs are ?

[@kansasgardener5844]

@@LUISGONZALEZ-jy3wq Depends on the year. You can look up the torque specs online. Mine was 203 ft lbs for the front. 177 for the rear.

[@LUISGONZALEZ-jy3wq]

@@kansasgardener5844 mine is 2011

[@kansasgardener5844]

@@LUISGONZALEZ-jy3wq 92 ft lbs for the front. 125 ft lbs for the rear.

[@Sambo365]

I just replaced my bearing on my 2005 FX35 but for some reason my lug nuts aren’t tightening in as far as my others are, did I do something wrong or anything you can suggest I check?

[@jimthecarguy]

Are you sure that they are the correct ones?

[@Sambo365]

Jimthecarguy Well i can say I did order the part off EBAY and did compare but I don’t know I’m assuming that might be the problem? 🤦🏻‍♂️