How to replace the grass deflector on a Toro Timecutter

[@TLMD]

Very nice Sir! It looked hard to wrestle into place but you made it look easy brother!

[@kbssmallenginerepair2615]

Thank you, my friend. It's always fun playing with springs...

[@dr.lmsb4456]

And the award goes too !!!! KB. Always a pleasure watching your videos brother . Take care & stay safe .

[@kbssmallenginerepair2615]

Thank you my friend! Such a high compliment, that I am so humbled by. Thanks brotha!

[@StellasScrappyCrafts]

thank you for this. I just bought a second hand xls 380 which I need to replace the deflector. It looks easy enough to do. Just need a second pair of hands to help.

[@tylereg4764]

Nice vid, made the replacement super easy👍🏼

[@Lovinflyindrones2022]

I’ve never changed one of them. Good job. Thanks

[@kbssmallenginerepair2615]

Thanks William!

[@scottbenjamin3811]

Thanks looks easy now great video!

[@laffilmfest3759]

Thank U for the demo....I subbed and appreciate the info !

[@kbssmallenginerepair2615]

Thanks so much! Hope it was helpful!

[@Mac210.]

Nice video!

[@kbssmallenginerepair2615]

Thanks Mac!

[@themowerman]

Easy to fit hard to film lol good one mate

[@kbssmallenginerepair2615]

Exactly!! Thanks for watching my friend!

[@FarmerGuy-1]

Thanks for the video.

[@kbssmallenginerepair2615]

Thank you for watching it!

[@henrymurawskibigdogrepair]

Ok something new great video kile

[@kbssmallenginerepair2615]

Thank you my friend!

[@Kookamungawerewolf]

It’s a lot easier than replacing the chute on a Toro Recycler walk behind.🤣 The spring on the Recycler has short tabs and gobs of resistance. Good video.

[@kbssmallenginerepair2615]

Ha you can say that again. Lose track of that thing and it'll go flying across the shop.

[@Methodical2]

Do they make a smaller rubber (or just a rubber one) chute for the Timecutter? It's just a matter of time before the plastic chute gets broken.

[@kbssmallenginerepair2615]

Not that I am aware of. You are correct, with the size and pliability of that chute, they are bound to break. And they are not cheap either...

[@herpalo1712able]

Thanks amigo

[@dickrenfro8535]

How would you pull a mulch cover on the same unit

[@kbssmallenginerepair2615]

It should come with instructions, but there will be a little plate that slides through the front bracket, and a rubber strap towards the back that straps down to the back eyelet. Then there is a hook on top that buckles down to the cover rod... If that all makes sense.

[@dickrenfro8535]

Thanks I appreciate that but what about the metal clip up at the top does that clip in the where the other flap is at

[@TheRustyRooster]

Gee KB ya make it look easy

[@kbssmallenginerepair2615]

Oh Rooster, you are too kind. It's tricky fighting a silly little spring and trying to film at the right angle...

[@jimx6512]

This doesn't help me much. My spring is on the left side of the rod as you look at it from the discharge end. It has no securing bolt on the bottom, just the long hinge pin and the spring. I'm trying to figure out how to put it all together. I guess I have a newer model.

[@JungleBobRepair]

People don't realize how dangerous that is.

[@kbssmallenginerepair2615]

Absolutely! Thanks for watching Jungle Bob.

[@davidcurnutt9584]

Looks like too much hassle. Just tell the customer to get off the left side of the mower.... j/k good video but you needed a 3rd hand lol.

[@kbssmallenginerepair2615]

Haha can't we all use an extra set of hands?