Lost a great mechanic friend today with cancer, praying for Niks family and friends 😢
@IndRepair3 ай бұрын
Prayers for you friend and his family. Sorry for your loss
@jeffbarkley47176 күн бұрын
So much great info ty! I have a 42 inche toro
@IndRepair5 күн бұрын
Thank you!
@jimmyhardy71883 ай бұрын
This is why you take care of your machines, people. If you take care of your machines, it will be ready when you get ready to mow.
@IndRepair3 ай бұрын
It sure will be!
@frankie75083 ай бұрын
Always a pleasure watching your repairs and hearing the explanation as you show us tips along the way. Another fine job! 👍👍👍
@IndRepair3 ай бұрын
I appreciate that! Thanks for watching!
@steveriggenbach903 ай бұрын
I have bench tested solenoids by hooking up to a 9 volt battery. As always a ton of info.
@IndRepair3 ай бұрын
Definitely works, I have a spot welder that has DC output I used to use a lot for this kind of testing. Anymore, I prefer quick and easy much as I can. A battery would definitely get us there
@danny8block25 күн бұрын
Mine didn’t even want to crank. I thought it was the parking break module but it turns out I just had to clean the connection. Got dirty and it was acting like it wasn’t working. Now runs fine
@IndRepair24 күн бұрын
Awesome news!
@garymoore83803 ай бұрын
Another good video. Great work!!!!!!
@IndRepair3 ай бұрын
Thank you!
@watermanone75673 ай бұрын
Good video, I am surprised that Toro went to those crappy engines. I have seen lots of issues with them. Kawasaki engines seem to be the top of the line lately, but very pricey.
@IndRepair3 ай бұрын
Kawasaki makes a great engine, it is all about the bottom line for many anymore unfortunately
@leosweeney79553 ай бұрын
Hi, invest in some JIS (Japanese Industrial Standard) screw drivers and/or bits. I never used them, till I learned about them, holly cow, what a difference, when u use the right tool for the job!!!! Just FYI.
@leosweeney79553 ай бұрын
I always broke them loose first, with pliers or vice grips, like u, till I tried them.
@leosweeney79553 ай бұрын
I'm 65, and just learned this difference, this year!!!! LOL
@IndRepair3 ай бұрын
I have some but these are not JIS screws I do not believe
@IndRepair3 ай бұрын
@@leosweeney7955 All the UTV and ATV carburetors we used to work on used JIS screws
@IndRepair3 ай бұрын
@@leosweeney7955 Yeah, the more you know! Great tips!
@bobspring67233 ай бұрын
Subbed.like your content
@IndRepair3 ай бұрын
I appreciate that and you watching!
@coryadams2054Ай бұрын
What's your honest opinion of that engine. I've had mine for 10 years now and no problems. Occasional backfire when shutting off, but just wakes you up. Are they any more problem prone that B&S or Kohler? Great video by the way. Very professional all the way thru.
@IndRepairАй бұрын
For all the grief I said about them when this engine was released I think they do just as well as Kohler or Briggs (if not better). Time has really shown they are holding up well in my opinion
@FUBAR0463 күн бұрын
Good God. Air filter is nasty
@IndRepair2 күн бұрын
Yeah, pretty darn bad!!
@tommyzee49082 ай бұрын
7/28/24 my toro z turn model 74330 .starter went o ground installed 2nd starter it went to ground also and dropped the battery down to 10vdc. And now battery won't take a charge . How do I start to diagnose and repair this problm
@IndRepairАй бұрын
What do you mean by went to ground? Start with a good battery and clean, tight corrosion free connections
@BillyRay-xk7qw3 ай бұрын
Coil
@IndRepair3 ай бұрын
Not on this one
@oldkicker89583 ай бұрын
Do you always have those parts on hand?
@IndRepair3 ай бұрын
Yes, we keep these carburetors in stock
@danielherlihy46852 ай бұрын
What kind of lift are you using?
@IndRepair2 ай бұрын
Find our review video comparing the three models we have at kzbin.info/www/bejne/pZ-Qi6yljZaoaqM
@Linda-ov1nc2 ай бұрын
Replaced the solenoid, battery, choke cable, fuel pump, plugs and filters still no start
@IndRepair2 ай бұрын
Does it turn over at all? Any noise?
@Mike_The_Hog_A_Nator3 ай бұрын
My Buddy has a 52" ExMark Radius. It runs great "If" the fuel cap is loose. Tightened down & it'll only run a few minutes then it's like a safety switch kicks in & it dies. New fuel filter stays full of fuel, plenty of oil, etc. Could it be the fuel cap not venting? Can you drill a hole or hole 2 in that plastic inner vent piece inside the fuel cap? I've had 1 place tell me it's the EPA Canister that "T's" off just past the fuel filter & hangs by a piece of hose. Fuel pump is fine, Kohler Engine. Thanks, Mike in TX 🤟
@IndRepair3 ай бұрын
It could very well be the canister, if the hose going to the canister happened to not be attached or to have somewhere to vent this would not be able to happen. If it is only when the fuel cap is on it is definitely a fuel tank vent issue
@Mike_The_Hog_A_Nator3 ай бұрын
Great thank you..
@rickbroerman92673 ай бұрын
You forgot to say LIKE and SUBSCRIBE. 😅
@IndRepair3 ай бұрын
Oh man, knew I forgot something lmao!
@sherrischneider27943 ай бұрын
That motor has a major oil leak on the left valve cover or maybe a head gasket leak, can't tell because of the dirt.
@IndRepair3 ай бұрын
Yeah, I estimated it but unfortunately can't fix them all like you want to
@outlet69893 ай бұрын
That part of the engine cover where the air filter goes looked dirty.
@IndRepair3 ай бұрын
It definitely was. I did clean it before marking it as finished and alerting the customer. Many times when doing a video I still get sidetracked and have to go back over things to get the fine details correct. Thanks for watching!
@bigsonslawncare3 ай бұрын
Always enjoy the content💯👍🏾
@IndRepair3 ай бұрын
I appreciate that! Thanks for watching and for your comment
@Rein_Ciarfella3 ай бұрын
Martin, do you ever blow out an obstructed 90 fitting in the tank by disconnecting the fuel line at the pump and blowing from that direction towards the tank? Then fish it out with a light and flexible grabber? I’m thinking an endoscope would aid in doing this, especially on ZT tanks.
@IndRepair3 ай бұрын
I have not ever done it this way but I suppose it is possible to do it like this
@kencurtis2283 ай бұрын
No Starts always check the gas First
@IndRepair3 ай бұрын
Yes sir!
@Linda-ov1nc2 ай бұрын
What about the starter
@IndRepair2 ай бұрын
Go through and figure it out systematically
@kencurtis2283 ай бұрын
Thank You for Sharing
@IndRepair3 ай бұрын
Thanks for watching ken!
@bobhaddock9573 ай бұрын
James Condon also has excellent video's
@IndRepair3 ай бұрын
I have seen a few and they are he makes great content for sure