How to replace the hose pipe in a Hozelock reel

This video shows how to replace a damaged hose pipe in a Hozelock auto reel. The hose pipe in this reel had split in several places and required replacing. The hose length is about 30 metres or £150 feet. This was a bit of a challenge as some of the screws were badly rusted and could not be removed due having damaged heads.

[@johnmheaton]

Perfect, exactly what I need to do, to my identical reel. Always nice to see the insides before venturing in! Thanks.

[@ultimatehandyman]

John Heaton You are welcome Thanks for the comment

[@philfyphil]

Superb. I went on to KZbin and typed in 'change hose on Hozelok' and this was at the top, the very exact same one as mine. Thanks for taking the time to do this. :-) 17 people didn't understand what that long thin thing is in your right hand. Couple of tips. The middle hose connector comes off by removing the green plastic clip which has three locating lugs holding the black collar. To get the hose off on the inside, first loosen the plastic toothed clip by lifting the top part carefully then pulling the underneath section outwards. Then I recommend cutting the old one leaving the attached piece at about a foot long. Then bend it vertically and spray some WD40 down. Leave to soak for about a minute then twist the piece of hose clockwise and anti-clockwise whilst pulling. It should start to loosen then pull off quite easily.

[@ultimatehandyman]

I'm glad the video helped Thanks for the comment 👍

[@commanderaverage]

Excellent timing with this, I have the same 30m Hozelock reel and mine has even bleached the same shade as yours lol. Had to chop around 10 foot off it because it is starting to perish and leak so thanks for sharing.

[@ultimatehandyman]

***** You are welcome Thanks for the comment ;-)

[@gateway8833]

That is one impressive screwdriver! I have never seen that type of hose reel here in the states, looks like it would keep alot of junk from getting rolled up in the hose. Thank for yet another well made vedio.

[@ultimatehandyman]

Abby Babby Thanks, they are pretty common in the UK. Thanks for the comment ;-)

[@Coffieman5150]

Thankyou that helps quite a lot, I didn't know where to start in trying to fix mine. Most useful.

[@ultimatehandyman]

Coffieman5150 You are welcome Thanks for the comment

[@mossed1449]

Thanks for this. A sugestion, at 00:48, you could have spent a couple of seconds explaining how to remove the back hose connector which involves removing a circlip. In later scenes, the connector was still in place as you dissassembled the unit which could confuse some to think you don't have to remove it..

[@ultimatehandyman]

It's that long since I filmed this I can't remember exactly what I did. I would not normally miss something out like that, but apologies if I did not include something. Thanks for the comment

[@user-np4ro8dy5o]

I have had my reel for around 10 years and it was well faded due to the UV damage but yours is not so bad. When you remove the middle plate you can really see what it was like at new. I just got my colour back to almost new green by using an electric heat gun. On medium power you can get reasonably close and after a few seconds the faded plastic turns green again. Experiment by time and distance and you will get back to an almost new colour and makes it look like you have just bought it.

[@ultimatehandyman]

👍

[@honestmcgyver]

Great video as always. Anyone would think they designed these to get most people to buy a new one or maybe it is done to try and save the spider nests inside :) keep up the good work

[@ultimatehandyman]

honestmcgyver Thanks for the comment ;-)

[@JasonDunlop247]

Reelly handy video (See what i did there) I have same reel, handy to know how about changing hose reel if need be. Thanks again...

[@ultimatehandyman]

Jason Dunlop Ha Ha, I hope yours lasts a while before it needs replacing. Thanks for the comment

[@BMcKenna]

Great video pal :D

[@ultimatehandyman]

Ben McKenna Thanks Ben ;-)

[@inthemix3013]

@@ultimatehandyman can u help mate. I have a hozelock reel and hose, and the feeder pipe from the tap to reel keeps blowing off when i pull for more hose

[@ultimatehandyman]

@ Gary Ashton You might be able to fix this by using a Jubilee clip, instead of the plastic hose clamp that is with the hose.

[@jackjones429]

Good video mate, where did you get them long screw drivers from ? Thanks buddy :)

[@ultimatehandyman]

Jack Jones They were on special offer at Screwfix about ten years back. They came as a set of four- that is the first time I have ever used them LOL Thanks for the comment

[@DarranCariadCoins]

Hi, any ideas on how to repair the winder mechanism. I have trouble winding in my hose because it seems it doesn’t engage. Sometimes it does and winds in great but it’s lucky if it works once in about ten winds.

[@ultimatehandyman]

Not sure, without ripping it apart again. Have you checked the belt, there is a chance that it has stretched?

[@shaunsims7570]

Any ideas on what the problem is with it retracting the last 2 or 3 metres. There's no water in the line and I have tried pulling out the full 30mtres of hoze and letting it go back slowly several times with no joy

[@ultimatehandyman]

Not sure, sorry!

[@louisbrittain981]

Hi thanks for the video, I have one of these and the handle stopped turning the hose reel so I can’t retract the hose. The handle turns, it just doesn’t ‘catch’ the hose. I asked Hozelock but they refused to help me in case I hurt myself!!! Any ideas?

[@ultimatehandyman]

I'm afraid you will have to take it apart to see what the problem is. I've not come across that problem yet, but it is likely something simple. Thanks for the comment 👍

[@PT4LifeYO]

Where can I source a new ‘guide’ that travels along the white threaded plastic bar. Mine has broken and the hose now jams as it’s not being laid on/off evenly.

[@ultimatehandyman]

You could try here- spares.hozelock.com/

[@JackMR12]

Thought I’d hit the jackpot with this video, however more recent units have a 4mm allen screw & Not posidrive (philips) head. :-(

[@ultimatehandyman]

Thanks for the comment 👍

[@ivormac2247]

@@ultimatehandyman Any idea Part Number for Toothed Belt in HOZELOCK Reel? Thanks

[@seanmcinnes1622]

Hi there, how did you get the back connector off, I have tried pulling mine but it doesn't want to budge, any tips appreciated.

[@ultimatehandyman]

I think I levered it off using a screwdriver, if I remember rightly it splits in half?

[@marcuswarrington]

There is a plastic spring clip around it that you need to lever off with a screwdriver then the connector just pulls out.

[@TheSas1967]

i have same reel and the hosepipe is jammed,wont come in or out,better to try and repair or just buy new one?cheers :)

[@ultimatehandyman]

It depends how much spare time you have. In many cases its best to get a new one, if the existing one is old. Thanks for the comment

[@isabellatjerrytaneyesurger7909]

What circular saw are you cutting for the plunge cutting? Can you give me the brand and model no.?

[@ultimatehandyman]

I don't have a plunge cutting circular saw, sorry.

[@daniellelogan60]

Is it possible to replace the whole unit and fit it on to the same wall bracket?

[@ultimatehandyman]

Not sure. They often change designs over the years, so a newer one might not fit an old bracket.

[@TheSas1967]

hi,me again,got the screws out,but how on earth do you remove the connector from the back?ive been pulling like hell and it wont budge,it mves sideways but wont come out,cheers for any advice :)

[@ultimatehandyman]

It's like a little plastic cable tie kind of connector (if I remember correctly), you have to push it to the side so that the plastic bit slips out from the rest of it. (I hope that makes sense) Thanks for the comment 👍

[@vaahee]

A video for this would be great

[@user-sl3rq7yc8d]

Beware that on the Hozelock 2496 Fast Reel they use T20 Torx screws for most of them there is one posidrive screw. Again you will need a long torx driver the 100mm standard blade length will not do 2 of them I have had to buy a 200mm bit with 1/4" drive as I could not get a torx screwdriver long enough.

[@ultimatehandyman]

👍

[@MsBling101]

hi i have the same hoze lock, but mine is leaking from the hose connection at the back, any ideas on how to fix this please.

[@ultimatehandyman]

These normally use a Herbie Clip to hold the hose to the unit, it might just need closing more with a pair of pliers, or you might have to get a new Herbie Clip, or it might be possible to use a hose clip/jubilee clip (can't remember if one will fit or not) Thanks for the comment 👍

[@Rush-gz9sx]

Or replace the centre section on the outside of the black shaft where the hose attaches that is also a major leak source that this video doesnt address. Hozelock have a long guarentee and will send you that part and a new hose free if within the warrentee period of 15 years for this model with an original hose. The free replacement hose warrantee isnt as long.

[@lee122620]

That's great but mine leaks from the inside , anyone know where I can get the 2 "O" rings that are insde the centre ?

[@ultimatehandyman]

"O" rings are normally pretty standard. If you could get one out and measure it, you should be able to find a replacement one. I have a "O" ring kit that has the most common sizes, it has been really useful over the years.

[@lee122620]

@@ultimatehandyman Thanks for that , I have taken them out so I'll try at a plumbing shop. :)

[@askme6408]

I still can't open my hozelock. I think It didn't show how to open the centre screw???

[@ultimatehandyman]

Not sure, without watching the video myself. I'm sure it was not that difficult when I did it, although you might have a different model.

[@ivormac2247]

Anyone know Part Number of Toothed Belt. Mine is broken.

[@ultimatehandyman]

Have you checked the spare parts manuals- www.hozelock.com/spare-parts-manuals/

[@radishpea6615]

very helpful video but the screws were not as easy to get out, as the holes had filled with dirt.

[@ultimatehandyman]

Thanks for the comment 👍

[@proce09]

Where abouts are you from?

[@ultimatehandyman]

proce09 Darwen, Lancashire ;-)

[@proce09]

Ahh thanks for the reply, greetings from St.Annes

[@ultimatehandyman]

proce09 I know it well ;-) Thanks for the comments

[@proce09]

No worries keep up the good work, see you around maybe

[@GenoMyster535]

You defiantly don't like saying the first letters of things like ole through ardered steel lel

[@ultimatehandyman]

Geno Myster It's part of the Darwen accent. Most people don't pronounce the "H". I'm just glad that accents only effect talking and not writing ;-)

[@GenoMyster535]

Haha cool :D