I have a 30mm slab. How long should my anchor bolt be? Can I use a wall plug and screw as well as an alternative?

do dishwashers have a service gap. the electrics are ran behind the appliance in 16mm deep trunking. or will cables need to be chased in the wall?

Thanks for the video I have to do this tomorrow, hope its ok 👍

Is it possible to fit it in reverse? For some reason both my doors have the cylinder the other way around.

Random Q but can inuse bucket instead of just putting the cement onto mud

Great video with great tips. Thankyou.

Just ordered the saw from Menards here in the US. The extra long track (110 inches total) is out of stock everywhere including the Evolution website. I got lucky and found one aftermarket site that has it in stock. They’re not going to sell many saws unless they offer a full-length track.

Hi, Is that x2 bottles of 1ltr inhibitor for a standard 8 rad system? Thnx

Well explained. Thank you!

Thanks you for sharing.

Can I use this to center punch a deep broken bolt to extract it ?? The way the bolt broke made a cone shape and it’s impossible to center punch because it slips to the side

Thank you, really helpful 😊xx

Had to replace a back box today as it was completely stripped on one side, will buy some of these if it happens again, thanks for sharing 👍🏻

Thanks for posting the video. I had a nut that was getting stripped and the 6 point ratchet worked like a charm.

Amazing

Great video from 6 years ago. We are making a scissor mechanism this way! I'm happy with this video because i was wondering how this worked for years

Fantastic video, used it when we thought we'd have to take the whole tap out! Worked a treat, the cold one was intermittent. Just the hot tap refused now 😂. Have to give it some proper elbow greese

I have a hollow metal door that has a barrel bolt on it to keep it closed (back of my garage) on the top in to the door frame. I can't keep the screws from pulling out and stripping the hole that holds the bolt mechanism. Thought I needed anchors so tried drywall anchors but because of the little spikes on the anchors that won't grab into the metal, they just spin and spin. Maybe this tool will work with the right kind of anchors. I don't know what kind of anchors would work on a hollow metal door. Help?

Would you advise using cold joint sealer first?(that spray stuff)

Takes toooo long

I cant believe how well the rubber band worked!

Thanks 🎉🎉😊

i wanna do the same for my 17mm aluminium i think through axle can i do this easily without problems?i want to install 2 squer sized bolts to atach a mtb trailer that uses i think 12mm axle mounts but my axle has a very large allen key one end and threaded other end.it should have enough thickness but its the pulling weight on the axle im concerned about.it seems like aluminium.

there fluid form tapping?

Is that sold in us

How closely could these be spaced do you think, without compromising the plasterboard?

They both suck😮

Great video. I didn’t realise I had to drill a hole to see the screw for the 2nd cylinder. Well explained. Many thanks.

Thank you so much..

This broke after 2nd use. Not sure what the issue is with the ratchet, cant see any visible damage. Bought it off Amazon so it might be a fake.

Hello, can I ask, if your base module width is 600, what is the width of the door? (I usually leave the door 4 mm narrower than the base module.)

You have just saved me hours of scraping a grove around a headlight on my truck. Someone had tried to reattach the headlight cover with silicone! After getting that cleaned out I will be using Flex Glue to put it back on!

So for dry cleaning you need to leave the foam on as well as the bag? Ive just bought one of these vacuums but it feels like its getting warm just wondered if i was using the filters correctly?

Why not get dowels that match the diameter of the diamond hole saw?

Nice little tips on top of the main points thanks!

Now what if the drywall shreds and the little pins don't work?

Youre supposed to use a setting tool to set these first, not screw them in mate

Which medium for use ? That means colour

Nicely done ❤

Thanks for the video. Looks like Darwen Tower in the picture you are hanging.

Great video. Just did mine today after watching your tutorial, which was really easy to understand and took the worry away from getting it wrong. All in all I'm happy, no leaking gutter and water drains away nicely with no standing or pooling water. I added my brackets every 50cm which I know is a bit of an over kill, but I ordered too many and they'd just be lying around eventually getting binned so just put them to good use. Thank you and keep up the good work.

super

Helped me realize I don’t need another port for a big ribbon cable on my mother board. I’m building a gaming pc but going to add 2 dvd burning drives to it. It’s June 2024. Thanks for the help. Hope your still alive. 😅

What's the point of hearing if you're going to wait for it to cool back down? Makes no sense and would be a waste of time. Just use a MIG welder to build up the bolt until it's protruding then use vise grips to back it out. If needed once protruding lay a loose nut over the build up and weld it to it then use a wrench to back it out. I use this technique all the time and it never fails. 👍

With more screws being made of chinesium this is more essential.

Good one,I be learnin

Are you using water or oil to cool the bit? What’s the benefit of one over the other? I’ve always just used WD40 in between drilling.

This is exactly my shower situation

Thank you!!!

Excellent tutorial and very easy to follow.