How to Replace Water Pump 2005-2010 Chevrolet Cobalt

Buy Now!
New Engine Water Pump from 1AAuto.com 1aau.to/ia/1AEW...
This video shows you how to install a water pump on your 2005-2010 Chevrolet Cobalt. The water pump keeps coolant flowing through your engine. Common failures of the water pump will leave the coolant leaking, or stagnant. Both will lead to overheating if left untreated. Install a new engineered to fit water pump from TRQ for total peace of mind.
This process should be similar on the following vehicles:
2005 Chevrolet Cobalt
2006 Chevrolet Cobalt
2007 Chevrolet Cobalt
2008 Chevrolet Cobalt
2009 Chevrolet Cobalt
2010 Chevrolet Cobalt
Tools you will need:
• Flat Blade Screwdriver 1aau.to/ob/1AXA...
• Phillips Head Screwdriver 1aau.to/ob/1AXA...
• Pry Bar 1aau.to/oa/1AXA...
• 10mm Wrench 1aau.to/oa/1AXA...
• 21mm wrench
• 10mm Socket 1aau.to/ob/1AXA...
• 13mm Socket 1aau.to/ob/1AXA...
• 15mm Socket 1aau.to/ob/1AXA...
• 19mm Socket 1aau.to/oa/1AXA...
• 7mm Socket 1aau.to/ob/1AXA...
• Cam Phaser Retainer
• Dead Blow Hammer 1aau.to/oa/1AXA...
• Trim Tool Set 1aau.to/oa/1AXX...
• Hose Clamp Pliers 1aau.to/oa/1AXA...
• Push Pin Pliers
• Ratchet 1aau.to/oa/1AXA...
• Socket Extensions 1aau.to/ob/1AXA...
• Torque Wrench 1aau.to/ob/1AXA...
• 13/16 Inch Wrench
• Brake Parts Cleaner
• Cloth Rags 1aau.to/oa/1AXS...
• Paper Towels 1aau.to/oa/1AXS...
• Pipe Thread Sealer
• Drain Pan 1aau.to/oa/1AXA...
• Magnet - Extendable
• Pick 1aau.to/ob/1AXA...
• Razor Blade / Gasket Scraper 1aau.to/oa/1AXA...
Subscribe: / @trq
⚠ DISCLAIMER:
While TRQ strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. TRQ is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.

[@TRQ]

√ Watch the Video √ Buy The Part at 1A Auto 1aau.to/m/Shop-TRQ-Parts √ Do it Yourself √ Save Money

[@victorcorrales2732]

thank you for taking your time for showing every step,very helpful.

[@bovideos9751]

Thank you for this video - it's very helpful, especially with the torque specs! One observation: when installing the new o-ring gaskets, adding some sealer would help a lot because the scraping action at 16:06 can easily create leaks.

[@erickl.r3553]

I wonder how much is the labor for this type of job?

[@pennyvillareal8017]

What's the labor cost for the water pump change?

[@matthewleland5568]

Ok what if I messed up and took the special tool off to soob

[@oldblueshhrchannel1847]

Ok, I just performed this water pump change. Followed your directions and on start up, there is a howling noise, is it a balance shaft chain tensioner issue or a faulty new water pump?

[@ogreckless3254]

I got the same thing probably we dry started it with out cranking water into it smh

[@oldblueshhrchannel1847]

Turned out, the balance shaft chain tensioner ratcheted tighter and the guide was the source of the howling. I suggest do not use the sprocket holder tool, take the front cover off to prevent the problem, remove the tensioner.

[@hendyzero5789]

Thank you so much

[@aaronmenchinger]

My problem I believe is actually the crank gear for water pump. Any way to replace it without removing the entire timing cover?

[@Red4banger]

Okay I see the tool now!

[@How2Man_101]

Many thanks!

[@oldblueshhrchannel1847]

Great video. Thanks for sharing. Did you say the water pump is driven by the timing chain? Actually it’s the balance shaft chain that drives the water pump sprocket. Just saying. Does 1AAuto have a full water pump kit, with the necessary gaskets , orings ?

[@davidgibson9049]

is that a 2.2 i don’t have enough room ! did you remove exhaust trying this job on the ground

[@quikgold513]

Shouldn't have to remove manifold if you have tool sprocket holder for water pump.

[@insurancedice]

Was the demonstration vehicle a manual trans setup? My 2007 LT 2.2 with automatic doesn't have nearly the same access to the coolant pipe from below. That said, I was able to get to the thermostat bolts from the top, reaching over the passenger side.

[@John-yo9jz]

So in other words, take everything out back there. GM has the worst engineers

[@Red4banger]

Did you use the gear holder for the water pump to keep it from ratcheting tight? You didn't show it on the video. If you don't use the tool the water pump will have a whine noise while the engine is running. The noise is destroying the water pump gear, putting metal shavings in your motor.

[@spencersayo2374]

Where do I get the gasket for the thermostat housing/water outlet?

[@TRQ]

+@spencersayo2374 Thanks for watching. Buy the part in this video on 1AAuto.com: 1aau.to/m/Shop-TRQ

[@ogreckless3254]

Lol did u show the 3 bolt take with trucks its fine i mostly used this video

[@daemonsilver3304]

Not so helpful. Doesn't address the issue of holes in drive wheel of water pump not being properly aligned to bolt holes in timing socket.

[@300bhp]

Is this water pump beeing lubricated by the engine oil?

[@MrLibertyordeath]

👍🏻

[@d21dusty72]

Very shitty engineering on this one