HOW TO REPLACED VALVE COVER GASKET MITSUBISHI LANCER

[@miguel24682468]

Followed your instructions the whole way took my time and everything came out flawlessly thank you!

[@oliverthemechanic8532]

I’m really happy mate that i help you on a simple way 😉 God Bless 😇

[@JakeMcGinn]

Thank you! You made it look easy, I'm going to try this on my mitsubishi

[@oliverthemechanic8532]

It’s not hard mate 😉 you can do it 😉

[@yanniesavaege3376]

What size tool or what kind of tool are you using to take the bolts off

[@oliverthemechanic8532]

Basic tools mate 10 , 12 etc

[@amonest]

i changed mine with the help of this video. thanks a lot😊

[@oliverthemechanic8532]

Thanks mate also for watching Im really happy that I help you on a small way 😉

[@sammyd901]

Oliver, what torque specs did you tighten the screws at and did you do a 2 step process or just followed the torque sequence?

[@oliverthemechanic8532]

Do the torque sequence mate and just check the rubber if already set properly just don’t over tighten it 😉

[@ADGamingCA]

thanks a lot im trying to do this on my own, already ordered the rubber seal let you know how it goes when im done

[@oliverthemechanic8532]

Thanks also mate for a positive feedback 😉 let me know how it’s goes ☺️ actually is not quite a hard job 😉

[@btherealbb]

It’s been 6 months. Still working on it?😂😂😂😂

[@keifuchan7265]

Really helpful video! May I ask what is the torque specs for the valve cover screws? Also the correct tightening sequence?

[@lilnml6988]

Same pls let us know not tryna break em or do i jus do it with the Milwaukee wrench😅

[@easyrider020]

thank you for posting .i have a question about this engine.which engine oil do you recommend?i live in west europe i used 0w20 im thinking to use 0w30?thank you

[@oliverthemechanic8532]

Thanks also mate for a positive response 😉 to tell you frankly I’m not quite sure what type of oil on a cold country it’s better ask mitsubishi dealer at your place 😉 I wish i leave at Europe 😅

[@easyrider020]

@@oliverthemechanic8532 each dealer uses different One 0w20 other for example 5w30

[@oliverthemechanic8532]

If you’re car is new Ow If it’s getting old already 5w 😉

[@mrcj8091]

Hi Oliver. What sypmtons did you experience that made you inspect the vc gasket?

[@oliverthemechanic8532]

There is no symptoms you can feel on the car mate just only oil leak 😉

[@heatseeker_]

Three bond way to go. 1217 good, but no gasket sealant or silicone needed at all?

[@oliverthemechanic8532]

I put a little bit mate on the gap i experience last time small leak on that side even a new gasket 😉

[@heatseeker_]

@@oliverthemechanic8532 ok gotcha. Great video. Super informative man 👍

[@oliverthemechanic8532]

@@heatseeker_ thanks also mate for watching 😉 God Bless

[@TheRivle]

Hi! Thanks for uploading. Question. Where can i get that sealer. I can't seem to find it. Or is any sealer ok

[@oliverthemechanic8532]

Thanks for watching also mate 😉 Auto Parts mate I highly recommend threebond mate 😉

[@Saric32]

Hii what kind of pistons does the lancer have, are they forged or ordinary. I'm asking about installing a turbo. I have a Mitsubishi lancer x 2009 1.8 petrol Thanky

[@oliverthemechanic8532]

Mate sorry im not quite sure 😬

[@Loseangeles]

Sir new gasket original or duplicate. My lancer me chnaged duplicate less than 10 k kilomeeter now leeking again.

[@oliverthemechanic8532]

Hnd po original yng kinabit ko aftermarket lng po 😉 hnd po normal na mag leak agad 😬 double check nyo po muna ang mga bolt at kng nakalapat po yong gasket 😉

[@Loseangeles]

@@oliverthemechanic8532 Thank u pari, im from india, watching video from Dubai.

[@oliverthemechanic8532]

Mate sorry I thought your Filipino just translate the one that I said 😅

[@jasonschroeder440]

Me to