How to reset the instrument panel on a PT cruiser

This video is a step-by-step process exclamation of how to reset your instrument panel on your PT cruiser

[@cissienall1856]

Wow. This was very informative. I just got my used 2007 Chrysler P.T. Cruiser & couldn't see where the mileage was listed in the dash. I'm confident that even I can do this, as a 69 year old woman. Thank You for this easy to follow video.

[@StansAuto83]

You welcome that why I make the videos to help those that don’t know about car.

[@cissienall1856]

I actually DO know a little bit about cars/vehicles... However, it's my 1st time owning a Chrysler P.T. Cruiser. People like YOU are a Godsend for those who just can't afford to get every little thing fixed by someone else. Thanks Again. We all appreciate the time you take to help others.

[@cissienall1856]

@@StansAuto83 How do I follow you on here ? I may have more questions as I get used to my "new", to me, USED P.T. Cruiser.

[@StansAuto83]

On the main page you hit subscribe button. And I think you can post questions via the community page on my channel

[@richardpatrick8346]

Thanks!! I found the problem. It was the electric fan

[@StansAuto83]

Thanks for the update

[@TheFerretsVarietyChannel]

Hi Stan i have no instrument function everything is dead. I have changed the ignition switch and checked fuses. Any advice please ?

[@Barriacade]

I have a 05 pt cruiser gt. I had both my rear bumper reflector lights go out.. where the heck is the fuse for those 2 lights that sit on the rear bumper?

[@stephanymccarthy9613]

How do I fix the cruiser not changing gears in the transmission when I'm driving it?

[@StansAuto83]

It could possibly be the input output sensor or the fluid pump if you have P 700 code you’ll need to have the transmission module scanned if that vehicle has one and it should be able to point you in the direction.

[@oscarorozco2130]

tks u stan for helping us garage mechanics i have a 2005 pt with p0032 and p0038 stalls and stop starts up ok then stalls what is the diff with the number i am going to replace both of these numbers thks again for your reply

[@StansAuto83]

Bank one in bank two oxygen sensors.

[@edgardh9359]

Hey Stan! I was watching that when the cluster starts to make the count down. It initially shows after this number (382964) My doubt is, what does that number represent? First I thought it was the mileage but it differs from the one shown at end of the reset (168782) Regards!

[@StansAuto83]

That’s a good question I have to look into it.

[@richardguerra5281]

@@StansAuto83 it might be the engine hours, just a thought.

[@StansAuto83]

Ya I am thinking so.

[@carolcomins524]

awesome

[@robertlaurain3094]

Hello Stan, I have an 05 pt .cruiser that I just bought, it had a bad battery when I bought it, and the only trouble light that was on is the abs light, so I changed the battery and since I did that it started flashing no bus on the odometer, also the check engine light, brake light, the solid red light is on in the middle, I believe its the security but not flashing, also the speedometer and tach aren't working, etc. OK, I've tried checking all fuses under hood, a soft reset, I tried resetting the cluster but it goes right back to the same thing after it runs thru the checks, do you think it needs a hard reset? or do you have any other ideas, but keep in mind I did not have this problem b4 I changed the battery, just the abs light was on!..Thank in advNe!

[@StansAuto83]

That issue I not ran into before. Are the grounds clean? These pt’s can be an electrical problem like a bmw.

[@Mc_Rc]

That's awesome ty

[@amyhendricks3627]

I don't know if you're going to see this, but I hope so!! I've done the key dance, and fuse check. Ultimately found that my error codes indicate cluster failure. My hope is to do this myself however, I can't find a good answer to the only remaining question. Where is the mileage stored in a 2008 PT Cruiser? Is it in the cluster itself, or in the vehicle's computer module? Am I going to end up with incorrect mileage by repairing with a used cluster? Or will the car's computer transfer the info to the used cluster?

[@StansAuto83]

In order to get the mileage to go in the used or new cluster you have to send it off to get programmed in there but the computer will always have the correct mileage and if you have a scan tool you will be able to read that but the scan tool has to be able to read that. Normally the dealerships can program a new cluster to read the correct mileage.

[@amyhendricks3627]

@@StansAuto83 can you tell me what I might expect to pay for that programming (after I install the cluster) at the dealership? I'd like to know what I'm in for...really appreciate your response; thanks so much!

[@StansAuto83]

Don’t really know what you would pay. Since each dealership charges different. I say just call and ask for the service department.

[@TheOldie56]

Is there an oil change reset light on a pt cruiser particularly a 2006?

[@StansAuto83]

I don’t believe so if I remember right, you have to reset it via a scan tool

[@TheOldie56]

Hmm I've owned this one fer 7 years can't remember lol. Thought it might be the gas pedal to the floor several times. Like jeep wrangler?

[@StansAuto83]

@TheOldie56 it might be cus pt’s do have some jeep parts and ecu programs.

[@Mc_Rc]

Curious would you know how change the ball on the stick shift its a manual transmission

[@StansAuto83]

There should be an Allen screw somewhere on the ball. I’m thinking because it should be about the same as a ball on the automatic.

[@bandmjones677]

My pt cruiser and it does while driving it and now even with brand new battery there is a light directly in the middle of the temperature and fuel are and it's glowing red even after I followed your directions. What does it mean with that middle light being lot up red& brake lights on as well. It will not turn over at all

[@StansAuto83]

Break switch maybe? Not sure without codes

[@tamekiabottoms9553]

What do I do for mileage, my battery went dead and it no longer shows number of miles on vehicle

[@StansAuto83]

Check the The instrument cluster fuse

[@zeejimi4044]

Hi ! The complete instrument panel of my PT Cruiser CRD is “dead”. Should I try to reset it, or is that pointless ? Thank you !

[@StansAuto83]

It would not hurt.but it sounds dead.

[@zeejimi4044]

@@StansAuto83 I tried it, and it unfortunately did not work..🤷🏼‍♂️ I have now also changed the 10A fuse for the “cluster” but that did not work either. It looks like I need a new cluster..😳

[@StansAuto83]

@zeejimi4044 ya I would say so. There not to bad to change out. But unless you have the replacement cluster updated with the mileage on the vehicle you’ll have a mileage discrepancy and the only way to get the true mileage. You’ll have to scan the ECU.

[@zeejimi4044]

@@StansAuto83 Another youtuber reported that the fault may lie in the fuse box in the engine compartment..🚗🤷🏼‍♂️

[@CHATO629]

Will this also work for 2003 Chrysler Town & Country?

[@StansAuto83]

I should. As far as I know. It works on most Dodge and Chrysler vehicles.

[@Viking158]

Hey Stan, I have an 03' Pt cruiser base that stalls while driving, sitting at a red light, idling, or just driving around the neighborhood, randomly. no check engine light, no error codes. If you're thinking it right now, chances are it's already been replaced. Any outside the box thoughts would be appreciated.

[@StansAuto83]

Fuel pump

[@Viking158]

Brand new

[@Viking158]

Brand new fuel pump, knock sensor, cam shaft position sensor, idle air control valve, maf sensor, ignition switch, oil sending unit, I haven’t replaced the TIPM yet, but I’ve heard that can fix my problem.

[@savion8]

I have an 01 pt cruiser and my security light is blinking along with all my interior light and the lights on the dash. It won’t crank or start. New battery put in also but still have the same problem. I’ve seen people say it’s the ignition switch, started, alternator, fuses, etc. Any ideas or suggestions to help fix this?

[@StansAuto83]

Check the body grounds in the engine bay And see if you can get any codes.

[@cathyyoung3285]

My 2006 cruiser randomly stalls out while driving. Gives me one chime, then dies. Ive recently replaced all the sensors and PCM board. One week ago to the day. Ran great during that week, but is now dying again. Any ideas?

[@StansAuto83]

Any codes? How’s the body ground that runs from the neutral from the battery? Are the battery cables connected and clean? Does it happen when turning? Does it happen when giving it throttle?

[@powerofknowledge7771]

Does this just reset the instrument panel or does it reset the computer also?

[@StansAuto83]

Just the panel to rest the ecu remove both positive and negative cables and hold the together for 30 seconds

[@rainclouds1188]

Hi Stan I have a 2004 PT Cruiser and all of my instrument panel light up at night but it's in the daytime when everything is dark, help pls!

[@StansAuto83]

Normally during the day it’s hard to see if it lights up in the day. If it’s does at night it’s working fine. When you turn on the marker lights or headlights the dash will also come on and so will the light buttons on the radio and Havc control, And shift selector.

[@zeke1mikey1]

Mine foesn't have the button

[@StansAuto83]

That is odd no trip button?

[@nathanshawjr8757]

I bought a used 01 Pt Cruiser and only part of the instrument cluster light up. I took it apart and checked all the bulbs and checked the fuses put it back in and now none of the lights work on the instrument cluster? Any suggestions. Also the fog lights quit working via the turn signal switch. Yes I do have the lights on the right setting on the turn signal switch.

[@StansAuto83]

Check the body ground that by the battery. Follow the negative cable from the battery to the body.

[@nathanshawjr8757]

@@StansAuto83 do you think I should replace the turn signal switch first

[@StansAuto83]

Ya if you can take it apart to see if it Corroded if it is you can clean it up in reapply contact grease sometimes it fixes it and that could save you some money.

[@nathanshawjr8757]

@@StansAuto83 I bought the new switch installed it and still they aren't working. Besides the body ground what else can you suggest.

[@StansAuto83]

I would go though the fuses make sure all are good. Also make sure the plugs on the cluster are snapped in and no wires are broke

[@darrenbennett1053]

Hey Stan . My 07 pt cruiser is having a issue with no running lights . Brake lights , backup lights , turn signal and headlights all work . But no taillights unless I hit my brakes . I’ve changed out the signal switch , bulbs and the sockets to the brake lights but nothing has changed . I’ve also checked all the related fuses but they are all good . What else can I check ? Any help would be greatly appreciated.

[@StansAuto83]

The switch may be bad or check the body ground right Next to the air box that runs from the negative line to the battery

[@StansAuto83]

Oh and some models have a relay built in to the switch.

[@StansAuto83]

It is possible it could be the brakes switch you could manually have somebody push it where are you look to see if the brake lights come on it’s located a little bit up from the brake pedal.

[@user-kf5ds1bq3d]

My 2001 ptcruiser stalls after driving for about 40 to 45 min and it takes starter fluid to get it started again i replaced oxygen sensor cleaned the throttle body only thing else would be fuel injectors and fuel pump dont think its fuel pump because it re s up fine not sluggish hss good power just stalls can take up to an hour to restart

[@StansAuto83]

The fuel pump could be going out. Does the vehicle have any codes?

[@levilee-vystubbs8774]

Hello. My 02 PT cruiser instrument cluster does not work when I turn on my headlights? Any answers to that?

[@StansAuto83]

Like the light? Or does the whole cluster stop working?

[@levilee-vystubbs8774]

@@StansAuto83 the light is not coming on. I changed the bulbs and the the lights aren't coming on

[@StansAuto83]

The switch that controls the brightness of the lights when you turn that you know to dim them or brighten them that does nothing or when you click it to turn on the dome light manually and turn it off does the dome light also turn on and off if that’s not working, it could be the switch that controls. The instrument cluster lights so you would need to get, a whole new one, which I believe it’s all integrated in the turn signals and the headlight switch

[@johnbonett5585]

Need fix for code 0440 for 2004 pt cruiser

[@StansAuto83]

The cause of code P0440 can be a loose gas cap which is the very common reason. P0440 is also set if any component within the fuel vapor system is leaking as in a gas cap vent, vent valve, carbon canister, fuel filler neck, or any of the many fuel vapor recovery components.

[@Rinizzlexo]

My 2008 pt cruiser oil light keeps beeping and flashing on and off whether it's parked or I'm driving. It just goes off and on and it's starting to drive me nuts. I've had my oil and all my fluids checked. Would this work to reset that?

[@StansAuto83]

Rhionna Gaal the oil presser sensor is going out

[@Rinizzlexo]

DODGE NEON RACING LLC. THANK YOU

[@verdellcunningham2749]

Rhionna Gaal photo

[@Rinizzlexo]

Verdell Cunningham no longer an issue. The timing belt and alternator went out on it. I had to get rid of it. Sorry!

[@Carlos-ms8zh]

Rhionna Gaal what was the reason for the light going off?

[@Seadweller451D]

Können Sie empfehlen Medikamente für Furz und Durchfall?

[@StansAuto83]

Nein, tut mir leid, ich bin Autotechniker und Sie müssen einem Arzt diese Frage stellen.

[@richardpatrick8346]

My 2001 pt cruiser is running warm. It’s running 3/4 way up and I changed thermostat. Is it suppose to run that warm?

[@StansAuto83]

I will make a video of the normal operation temperature area for the PT.

[@StansAuto83]

Correct operating temperature for your PT Cursierkzbin.info/www/bejne/ap28q5qNZtZooKs

[@flex-jsteve540]

May have fixed my problem will see soon thank you

[@StansAuto83]

Good hope it works!!!

[@richardguerra5281]

Mine said airbag, at the end of the test. Any idea why?

[@StansAuto83]

It’s possible the clock spring could have an issue or one of the airbag wires or plugs or fuse

[@derekwells7516]

My 08 PT cluster blinks 5 times then goes black. The gauges still function properly. What i have discovered is it turns off my tail lights. Headlights and brake lights work just fine but no tail lights. Tried the reset but still occurs. Any help will be appreciated! Thank you!

[@StansAuto83]

I would check grounds and also check the wires there may be a short.

[@jakuboziebo4118]

Hello, i have problem with abs and track light. It flash but mechanic told me that it is electric problem. Can i restart it? It sometimes flashing sometimes No

[@StansAuto83]

I would go to a different mechanic and have the Abs system looked at and the traction control. This reset only works for needle issues. But also check the fuses for the abs and traction control. Also make sure the brakes are good and the alignment is good.

[@Madnezzmonroux]

My horn isn’t working on my 05 pt Cruiser. Horn pad feels like nothing is there

[@StansAuto83]

Could be clock spring is going bad.

[@audreygivens3464]

too many problems since i bought my 2003 pt cruiser , engine light on second day i bought it , checked with my OBD it says p0441 last time i checked it was p0440 , two days later the check engine disappeared from the dashboard even i still get it in my OBD !! went to change the oil after i got change oil light in my dashboard , second day i started to hear some kind of noisy sound coming from the exhaust and the car struggling while driving it on uphills , my car inspection is about to expire !

[@StansAuto83]

That could be a bad cat. Also the oil pressure sensor.

[@riooproductions9227]

Pt 2001 it cranks but won’t start. I get error codes of P1193 and P1684 any suggestions?

[@StansAuto83]

Faulty Inlet Air Temperature (IAT) Sensor. Or P1193 P1684 is TCM (Transmission Control Module) is disconnected from the battery power B+ or ground.. The inlet air temperature sensor is located in between your airbox and your throttlebody. And make sure your battery has enough power and cranking amps to be able to give enough voltage to your TCM.

[@pkelso05]

Im guessing this wont help my cluster lighting flashing off and on mostly while driving, at times the car shutting off altogether. It starts right back up. Any suggestions would be appreciated

[@StansAuto83]

I would check the battery connection. Make sure there not lose or have lots of corrosion.

[@pkelso05]

That has been checked numerous times...even new battery. New alt and fuel pump.

[@StansAuto83]

Has the ignition been looked at?

[@pkelso05]

No. My son and I did try to tighten up the wires on the left side of the steering column

[@StansAuto83]

Ok look at the grounds make sure the right and clean of corrosion. Also it could be the neutral safety sensor. Can u sift out of park without the key in or pressing the break pedal?

[@klsrecords]

I have a 05. Oil light won't go off...any suggestions?

[@StansAuto83]

If you oil level is right. Then it’s eather the oil pressure sensor or the oil pump. But more than likely it’s the oil pressure sensor.

[@klsrecords]

@@StansAuto83 I'm going to try another half quart of oil if not... oil pressure sensor. Any idea if this is a do-it-yourself job? I have mechanic experience but not many tools. (In Hawaii) I really appreciate the reply

[@StansAuto83]

2002 Pt Cursier Oil Pressure Sensor kzbin.info/www/bejne/h53ReXhpp8pjkMU

[@ozmarwolf]

what is it for ?

[@StansAuto83]

If a needle gets stuck or doesn’t set properly.

[@javierrivera5635]

My pt 2006 cruiser the speedometer don't work what the miles I'm going it shows different will this method work

[@StansAuto83]

Probably not. I would replace the input output sensors on the transmission. If there is a code as in a 700 code. Or the cluster is bad. But more than likely it is the sensors.

[@javierrivera5635]

DNR Stan’ Auto Repair ok thanks

[@StansAuto83]

You are welcome

[@ryanwatts4194]

my cluster panel stopped working on my 2006 pt cruiser today. turned off the car to go into the bank and when i came back out nothing working and the interior light won’t work either. checked the fuses and they seem to be okay. i still have the headlights breaklights and turn signals but nothing on the dash. radio works as well. any suggestions?

[@simplelifewithsarah]

xofrnkiero andthe cellabration mine does the exact same thing! Let me know if you find out how to fix the problem

[@ryanwatts4194]

Sarah Chaney i actually figures it out. it’s the hot wire that lead into the fuse box. take the terminals off the battery before you mess with it though or you’ll get shocked.

[@StansAuto83]

Ya you are on the right track. Good job!

[@georgetait3530]

@@StansAuto83 Do you have a video showing this fix?

[@StansAuto83]

No I do not. I not had a PT come in with this issue.

[@queenshirley2801]

How do u know that yr cruiser has a lectrical promblem

[@StansAuto83]

Normally the lights will short out. Fuses will blow left and right. But most times it’s bad grounds.

[@dannyboy74]

Will this help a “No Fuse” code on a 2002? Thank u.

[@StansAuto83]

No is the dome light working

[@dannyboy74]

Stan’s Auto Repair no dome, door locks, or radio.

[@StansAuto83]

Ok then check the fuses and change the dome light

[@Diamonddog59]

Thanks, I managed to put the wrong radio code into my 2004 PT Cruiser and it is locked, after just one attempt. Any idea how to reset the radio so I can put the right code in? Thanks

[@StansAuto83]

I hate to say I don’t know sorry

[@Diamonddog59]

thanks for getting back to me , you have to leave the radio on for 30 minutes and it resets.

[@StansAuto83]

Diamonddog59 oh ok that’s great to know 🏁🏁

[@johnbonett5585]

Need fix for code0440 for 2004 pt cruiser

[@johnbonett5585]

Need response please

[@johnbonett5585]

Please give a response to my question

[@StansAuto83]

The cause of code P0440 can be a loose gas cap which is the very common reason. P0440 is also set if any component within the fuel vapor system is leaking as in a gas cap vent, vent valve, carbon canister, fuel filler neck, or any of the many fuel vapor recovery components.

[@lisaperryman1268]

Hi can someone help me ?? I have a 2002 Chrysler pt cruiser dream &only dashboard light won't light up or glow when I turn my lights on the dash light fuel & temp dashboard circle won't light up so what can I do ??

[@StansAuto83]

Lisa Perryman check the fuse for the instrument cluster.

[@robynmaini9819]

My 2007 PT was in storage with a flat battery. on charging the battery and subsequent starting of the car the display is now in a foreign language. How do I change this?

[@StansAuto83]

I never heard of that. I did not even know this could happen. I will see what I can find out.

[@StansAuto83]

If you can get into settings and find the language settings change it there. Or you will need to plug it up to a computer system to get in the ECU to change the language

[@luisjimenez8258]

My speedometer hand will go almost all the way down and when I start it up, the hand will stay at 0. Any tips?

[@StansAuto83]

The speed sensor could be bad. Or the speed hand is broke.

[@luisjimenez8258]

Stan’s Auto Repair Thank you. What would I have to do if the speed hand is broken?

[@luciendebeer5574]

At 1.20 sec 1 light does work- do not know if it is trunk open

[@StansAuto83]

Not sure there.

[@j.18wheeler17]

How does one fix the light for the speedometer?

[@StansAuto83]

To fix the lights that are out on the cluster you’ll need to remove the cluster then remove the mini bulbs and replace those if the whole cluster doesn’t light up then that would be your switch that is located on the same switch that turns the headlights on where you can turn the lights brighter or dimmer or turn on your dome light

[@j.18wheeler17]

@@StansAuto83 hey thanks for replying

[@StansAuto83]

Your welcome

[@get-onskopje3510]

Pt cruiser p1490 any help over here? :)

[@StansAuto83]

It’s the cooling fan. The fan motor may lost low or high side or both or the relay (s) are blown.

[@get-onskopje3510]

@@StansAuto83 thx stan for the fast answer did changed the relays both of them now the high speed fan kicks in and doesnt turn off till i shut down the car

[@thwayne901]

My diagnostic trouble shooting codes. PT cruiser 2001 P1684 Battery disconnected in the last 50 starts The battery has been disconnected within the last 50 starts. P0320 No crankshaft reference signal at PCM No reference signal (crankshaft position sensor) detected during engine cranking. P1391(M) Intermittent Loss of CMP or CKP Lost of the cam position sensor or crank position sensor has occurred. P0340 (M) No cam Signal at PCM. No fuel sync P0442(M) Evap Leak Monitor Medium (0.040) Leak Detected. A small leak has been detected in the evaporative system. P0455(M) Evap Leak Monitor Large Leak Detected A large leak has been detected in the evaporative system.

[@StansAuto83]

Crankshaft sensor may need to be replaced also check your evap system for the fuel

[@shannonharris2073]

What's that got to do with the gages getting stuck? You started to tell us how to get them unstuck then u started talking about something else.

[@enriquepulido5768]

My 2005 pt crusier has P 1604 code how can I fixed

[@StansAuto83]

Ok try this first. Remove the positive and negative cable from the battery. Touch them together for 30 seconds. Then set them aside for 5 minutes. Clean the cables if needed nd the battery. If the code comes back. The PCM may be failing. You need to then take it to the dealership and have the do a diagnosis. Some time if that’s the issue an update to the pcm or a reprogramming will fix it. But try the battery cable first. What it does is drains the power from the PCM. The the 5 minute wait resets the PCM. Hope this helps.

[@enriquepulido5768]

Thank you

[@MexicanoenUs]

p1604 how fixed?

[@StansAuto83]

Does the starter turn over? When you turn the key? Or does it do nothing?

[@Jrodz53]

PT Cruiser...What Year?

[@StansAuto83]

The one in the video a 2002 the one with the issue is a 2007

[@beguma8868]

Espñol?

[@StansAuto83]

no español, pero puedo usar el traductor de Google para responder a los comentarios

[@joanramos4666]

Im having some problems with my 2004 pt cruiser. Dought I had a starter and replaced it. Ok still having the same problem.I have power all over the car but won't turn over nothing at all .anyone with this problem

[@StansAuto83]

+gary rossy does your PT have a chip key (security system)?

[@joanramos4666]

DODGE NEON RACING no sir.

[@joanramos4666]

DODGE NEON RACING got rid of it champ I appreciate your response

[@johntravisstevens6062]

gary rossy Check your IOD fuse under hood. It'll have a black clip over it,you'll need a very small screwdriver to pop it out. I had this problem and replaced inexpensive fuse and radio door locks and overhead light works now.

[@mysticrootsdivinations1825]

That wont mess with the miles and the airbag/seat belt will go off

[@StansAuto83]

No it won’t rest the odometer or reset any errors with an airbag light. You’ll need a scan tool that does airbags to see what the airbag light is on for.

[@mysticrootsdivinations1825]

Okay thank you i think its my seat belt bc when a passenger buckles in it goes away its a 2007 touring

[@StansAuto83]

Ok. The 2007 models can be a headache! I have one now I am working on for the famous no start!

[@YU5CF-sv2cq]

This way is no good for my pt cruiser it doesn't work 👎

[@Jeaniesunshine-fb5rk]

Little lic. Of engine

[@burnnotice5086]

My speedometer shows 5 mph faster than actual speed. Inaccurate speedometer.

[@StansAuto83]

That could be the input and output sensors on the transmission

[@leedelany2832]

Well it didn't work for my '06 PT, neither did the rapid pressing of the accelerator on another youtube vid.

[@StansAuto83]

That odd it should.

[@alansmith5816]

What is the object of resetting the instrument panel?

[@StansAuto83]

Alan Smith it helps reset the needles if they get stuck. Also if the mph needle is off it helps rest the needle. It is also used to make sure the cluster works and all the warning lights.

[@alansmith5816]

Thank you, I'm going to try it for my fuel gauge. It never goes to full when the tank is full.

[@StansAuto83]

Alan Smith ok if that does not work the floater in the tanks may need replacement or reset

[@alansmith5816]

Ok, how would I reset the floater in the tank?

[@StansAuto83]

Alan Smith you would have to pull the fuel pump