This video is a informative video on what entails in resizing 5.3 ls rods with ARP bolts these are cracked cap rods. I will take you through the ins and outs on properly resizing these rods.
Пікірлер: 18
@cobrasvt3476 ай бұрын
Same here. Would like to see how the rod hone works. 👍
@doggettsoldironrodscustoms93764 жыл бұрын
I didn't know you shouldn't grind these caps , good to know, not all rods created equal
@doggettsoldironrodscustoms93763 жыл бұрын
@Oscar Johan You lost me? who and what are you talking about ? Please an Thank you
@doggettsoldironrodscustoms93763 жыл бұрын
@Beau Landon What are you two talking about. This is a video about rods?
@forcefedturbine Жыл бұрын
800hp turbo junkyard motor enters chat: 😳
@olduhfguyАй бұрын
Watching your techniques. What's the grit of the hones ? I take it that the eccentric movement is normal. Just used my dial bore indicator on a cracked 4.7 Chrusler rod that spun, and now measures .003 out of round, so paperweight ?
@TwinTurboLsx Жыл бұрын
Have to disagree with the power ratings. I’d say 600-700 with decent tune is about the cut off where you’re not rolling the dice. But plenty making more than that for a long time. Crank is good for far more than that. Although it will start to flex around 1000+. Which isn’t good.
@whiplashmachine3 жыл бұрын
I learned how to resize on a hone like this👍
@kermets4 жыл бұрын
Thanks so much for the great video .....if it was a Gen 1 Chevy before the resize do you have to face the Caps before re sizing ? ......also are there other books you can download to give us specs for say cranks , bore size, lifter bore size etc etc? Brett
@doggettsautomotivemachinin6754 жыл бұрын
Thanks Brett we appreciate the support man! Yes traditionally we would surface the caps in our cap grinder and then re-torque and hone to size. As far as books to download im not sure on. How ever if you contact Mahle Clevite and request a catalog there bearing books have all the specs in them for various vehicles and also supply alot of torque specs. Hit us up on Facebook if have any questions or need any info thanks!
@nextgen19393 жыл бұрын
Never seen the kwik way hone before. I have always ran Sunnen. Will it run Sunnen mandurals?
@DELTRANIO99 Жыл бұрын
Great vid just wondering after resizing do you still use the stock size bearing ?
@m.a.p.4hp73711 ай бұрын
The outside diameter of the bearings is the stock size. The inside diameter of the bearing depends on the crankshaft journal size.
@lazaromarino92004 жыл бұрын
Great video! Time to start new ways to machine these rods. Incidentally some of the correct 350 engines also use powdered metal cracked cap rods. What do you charge to resize those??
@lazaromarino92004 жыл бұрын
Stupid spell check I meant Vortec 350
@doggettsautomotivemachinin6754 жыл бұрын
Thank you Lazaro! We appreciate the support from our fans. We charge $24 dollars to resize the big ends of the rods $28 if we are changing rod bolts. Check us out on Facebook and shoot us a message if you need any machine work done!
@jjmccloud2 жыл бұрын
I don't like these rods lol but im a gen1 guy still so.... 😆
@mathewhoffer4541 Жыл бұрын
Why bother to spend the money for the bolts and then also pay the labor to install them and re size them ? wouldn't it be better to just buy a forged set of rods ? I mean if you were the machinist and just your time or a buddy doing you a favor the cost of a set of bolts is a no brainer but SHIT who wants to pay machinist labor rates for a marginal upgrade that is vastly inferior to just getting a low cost set of 4340 rods ? Now I can see where a shady machinist would push this upgrade because its mostly labor and if it fails he gets a repeat customer that needs a lot of expensive engine work done. This is like telling a crewman on a nuclear submarine that sinks to the bottom of the ocean to simply take a deep breath and swim to the surface .. no worries