As a new unimat owner, this will be useful information. Thank you for sharing
@s.b.martin95326 күн бұрын
Very clear instructions. Thanks to you I got it right the first try.
@gyrogearloose1345 Жыл бұрын
Thanks for this useful information . . . I just saw an ad for Unimat 3 lathe in my city, and thinking about 'upgrading' from Taig.
@olivvapor4873 Жыл бұрын
Thanks, you will save my life when I need to reverse the jaws ! 😊👍🏻
@machinist_matt Жыл бұрын
Thanks for watching. 🙂
@LANCEPOLYMER2 жыл бұрын
Many thanks Matt! That was as clear a set of instructions as you could get.
@karlthroup32779 ай бұрын
Great stuff, spent two hours before I thought of KZbin ,very helpful.👍
@colvinator16112 жыл бұрын
Thanks a lot for that information. I'm just waiting for my lathe to arrive.
@fail_fast7 ай бұрын
Thank you!!
@colemine70082 жыл бұрын
This was a great video. Thank you.
@adrianplummer85032 жыл бұрын
Very helpful thanks 😊
@AHTiraq4 ай бұрын
Can the EMCO S L lathe make a wheel of fafon or aluminum with a total diameter of 10 cm? I hope to get the answer.
@JohnKoppan-hv1di Жыл бұрын
Thank you _ for that information - You are superman.
@DavidPlass2 жыл бұрын
On my SL I kept 2 in the same place and swapped 1 & 3
@paultrimble93902 жыл бұрын
Nice
@machinistmikethetinkerer48272 жыл бұрын
Hey thanks! I haven't had to switch out the jaws yet and knew there was a sequence for them but this explains it and makes it memorable. At my age, that's golden! Thanks for the tip👉👉👍👏
@machinist_matt2 жыл бұрын
I remember the first time I tried switching them around. I think I tried every combination possible before getting it right! 😭🤣
@machinistmikethetinkerer48272 жыл бұрын
Yeah in the manual they mention it real quick with the number sequence. Your hack is way better.
@justinahmann9482 Жыл бұрын
So I'm confused. So number 1 jaw is supposed too go with numberr one slot but what if the sequence of the teeth do not.match the numbers via the slots?
@machinist_matt Жыл бұрын
In the normal position the numbers on the jaws should match the numbers on the chuck. No need to worry about the teeth spacing/sequence. In the reversed position ignore the numbers as they won't match. Identify the teeth spacing as shown and insert them in order.
@justinahmann9482 Жыл бұрын
@@machinist_matt thank you my brain was fried like a bad perm. I honestly thought for a minute I was going crazy. I never think outside the box it's always adjacent or perpendicular or hell even just insides sometimes 😅😁 I now have it together and I am now turning and facing a plug for my stripped mounting plate. U the best.
@justinahmann9482 Жыл бұрын
@@machinist_matt wow. Now I feel even more stupid because you even said it in the video. I guess I wasn't paying enough attention. Perhaps the wife 🤔
@machinist_matt Жыл бұрын
@@justinahmann9482 No worries, glad to help! Good luck with your project. 🙂
@justinahmann9482 Жыл бұрын
@@machinist_matt thank you, so far everything is swell just need a tap 🥺 one worth tapping with anyways, would hate too have a harbor freight tap break in the beautiful piece I just made 😅
@robertvanetten90910 ай бұрын
Do you know safe way to remove dead center from tailstock
@machinist_matt10 ай бұрын
If it has become stuck I would disassemble the tailstock and push it out from the rear of the barrel. 🙂