In this video is what I do almost every day and that is polish metals. I am sharing my way of polishing, what products I use and a bunch of tips and tricks.
Пікірлер: 23
@bencandal7663 Жыл бұрын
One of the best In the business!!!👏👏🔥🔥
@thejelletouch Жыл бұрын
😎😎
@lindseyliddic8845 ай бұрын
Great content. Can you do a video on polishing over various rivots?
@thejelletouch4 ай бұрын
when I do a trailer rail I'll make one!
@stevenjamieson5461 Жыл бұрын
I just became a fan
@thejelletouch Жыл бұрын
😎😎
@barreltwist5466 Жыл бұрын
What is the recommended RPM for sanding?
@thejelletouch Жыл бұрын
I usually sand between 3500 and 5000 rpm. Beginners I would recommend not to go over 3500 until you master it.
@justinedmondson35018 ай бұрын
When u have them to that point how do you maintain the shine?
@TheRoadhammer3794 ай бұрын
Hand polish to maintain or buy some aluminum sealer like SHINESEAL.
@thejelletouch4 ай бұрын
@@TheRoadhammer379 I like to hand polish it to maintain.
@Warren.Boychuk11 ай бұрын
How much do you charge per hour for work like that?
@thejelletouch4 ай бұрын
charge by the piece
@peted5205 Жыл бұрын
How much is something like that cost? I have 150 tanks
@thejelletouch Жыл бұрын
The average tank goes for 180. Tanks all the way around off the truck start at 275 It includes 2 steps sanding and 3 steps polishing every additional step that's needed 20 extra. If you legitimately have 150 tanks I will give you a better price. You can always give me a call for more info. 506-961-5616 thanks and have a great day!
@Gonzalez78711 ай бұрын
How much u would charge on a job like that?
@thejelletouch11 ай бұрын
Tanks start at 180.
@Josiah_Harder11 ай бұрын
Im having the hardest time getting a clean look and clarity on my tanks. I have hazey streaks left by the wheel that will buff out if i use lots of compound but the wheel will just leave more streaks somewhere else then. I took a short video if you wouldn't mind watching and giving me your opinion. Im almost ready to give up it's very frustrating. kzbin.info/www/bejne/fZTQfYN5rtZspMk I sanded beginning from 120 up to 800 and then I use my orange wheel and brown compound at 3200 rpm. It seems no matter how hard or many times i go over a section it will leave hazy marks or streaks. My yellow wheel with green compound will leave marks and even my white wheel with purple even leaves marks that i have to fix by trying to go over with my cuts again!
@thejelletouch11 ай бұрын
It sounds like you going to need to use some more speed like a 6000rpm grinder for cutting. It's a bit more dangerous and the grinder is heavy! But of you sanded down from 120 to 800 I'm sure you can use a 6k it will give more heat so also more shine
@Josiah_Harder11 ай бұрын
@@thejelletouch thanks for the tip! Maybe that's the issue cus Ive gone over these cap ends so many times. It's always the end caps of the fuel tanks that give me trouble
@Josiah_Harder11 ай бұрын
@@thejelletouch and I realized that my yellow and white wheels aren't leaving marks they're just revealing the improper cut
@ChrisMoss-xd7kx11 ай бұрын
Why are the pads that i have so hard
@Gonzalez78711 ай бұрын
Cuz u need to soften them with the wood tool withe the metal teeth he is using.