How to scrap an electric motor out of a furnace. COPPER TREASURES.
Пікірлер: 43
@vibesmom5 ай бұрын
Holy cow I have one of these just sitting waiting for me I just haven’t attacked it yet. Thank you!!
@JimboScrapper5 ай бұрын
Your welcome
@mamanzanares Жыл бұрын
12:35 oooooo! Could you please tell me where you take them to and how to micro scrap it. Thanks for the awesome videos, Jimbo!!
@scrappingonthefly77 Жыл бұрын
Nice little bit of copper under the cap on the gas valve
@JimboScrapper Жыл бұрын
Hell yeah
@scrappingonthefly77 Жыл бұрын
Done several of them in my life, some of them aren't easy, depending on how easy the shaft comes out of the swirl cage !! Good job jimbo !! #3 sheet copper here. My local yard sucks
@ScrappingwithGrandpa Жыл бұрын
Glad to rewatch. I have a few to do
@SilverScorpion3 жыл бұрын
Wow Sheet copper for free! That is nice! Im going to try your way of taking those blowers apart! Thanks for the tip!
@JimboScrapper3 жыл бұрын
There normally alot easier than that, that would be good copper to make a skeleton key
@silverunicorn26453 жыл бұрын
Yay! I made a new friend😃👍❤️🦄
@JimboScrapper3 жыл бұрын
@@silverunicorn2645 thank you for watching
@maritimescrapper11 ай бұрын
Awesome video! SUBSCRIBED!!!
@JimboScrapper11 ай бұрын
Awesome! Thank you!
@godisgreat84623 жыл бұрын
Hello from the rising sun Japan I am a new subscriber
@JimboScrapper3 жыл бұрын
I appreciate the subscription thanks for watching
@hipolitozamorano2214Ай бұрын
Its always a daymaker when its gold color inside and a sad day when its majority all silver color insides why do they use aluminum and other times copper ?
@SMKay3 жыл бұрын
Silver Scorpion sent me, nice to meet you Jimbo!
@JimboScrapper3 жыл бұрын
Nice to meet you my new friend.
@cuscrapping3 жыл бұрын
#1 for sheet copper?!?! WOW!! Sheet copper is #3 over here! Congrats!!
@JimboScrapper3 жыл бұрын
Yes sir #1 my yard is really good to me with certain items.
@thensh1tguy Жыл бұрын
I cut the blower fins with sheet metal cutters, then cut the shaft with a Sawzall. Works a lot better.
@tomitstube2 жыл бұрын
those blower motors... some are easy as pie, others a real pain. recently had one that was a pain in the ass, then the motor windings turned out to be al. 35 lbs of sheet copper, nice, that's a lot of stripped wire... i'll find some nice copper tubing once in a while, usually all green and dirty, i'm guessing they don't know it's copper and toss it, but the trained eye one day i saw a bunch of copper tubing sticking out of a garbage can... it was a copper colored garden hose. one night i saw what looked like a couple pieces of plywood leaning on a garbage can, checked anyway, it was two thick metal plates, about 200 lbs of clean steal.
@JimboScrapper2 жыл бұрын
That's awesome, thank you for watching
@mikeburke8656 Жыл бұрын
I did one and treated the shaft with penetrating oil and it allowed it to slide off.
@ScrappingwithGrandpa Жыл бұрын
it works for me that way also
@ScrappingwithGrandpa3 жыл бұрын
Nice
@Wade-LS12 ай бұрын
Spray some lubricant on that motor shaft then use sand paper to remove the rust then rotate the shaft to break it free
@louisrichards3702 Жыл бұрын
i dont even try to get the shaft out,, i remove the 4 long bolts, usually a impact will do it while u hold onto nut with other hand,, if not angle grind the top of bolt off, real quick ,, hammer the AL end off,remove the 3 bolts holding motor to blower and remove motor, it usually slides right off leaving armature in side,, the AL end is easy to clean up, i use a 20 inch long flat screwdriver to pry off inside steel cap ,then a piece of rebar sliding through to knock off the dirty end cap, and a 10mm socket to hammer out sintered bearing, then u have clean AL casting.if you must remove shaft they make 8 point sockets for square headed bolts, or use a open end of a combination wrench of the right size,i save oil from ac compressors, u can use that to lube up shaft let it sit , then use a 5 pound sledge to slam against end of shaft , i should fly right out , but i would remove AL end cap opposite shaft first.
@JimboScrapper Жыл бұрын
👊👍
@ScrappingwithGrandpa Жыл бұрын
I learned from the best
@JimboScrapper Жыл бұрын
Lol thanks buddy
@DeanG552 жыл бұрын
Dang Jimbo, you gettin' old or something? It sure took a long time to bust out the copper in that squirrel cage!! 😉
@JimboScrapper2 жыл бұрын
Lol
@scrappingonthefly77 Жыл бұрын
🤣
@markb2007 Жыл бұрын
For stubborn nuts a 90 degree long reach needle nose works great.
@JimboScrapper Жыл бұрын
I'll have to try that, thank you.
@gulfcoastacrscrapper65233 жыл бұрын
Stainless steel pole I would list it for sale or make flag pole and resale. Sheet copper WOW!
@JimboScrapper3 жыл бұрын
I don't know how much the stainless is worth
@ScrappingwithGrandpa2 жыл бұрын
I’m getting ready to do one now off camera and then if it turns out OK I’ll try it on camera lol I’m cheating.