How to select the right Spray Tip Size and Type

[@TScott-vp9zv]

Mannnn, your videos are so thorough but yet succinct! Thanks for the info. Cheers from Houston, Texas!🙏🏾✊🏾

[@stevetryit]

Very good! I've been spraying houses since 1979 but I've gotten rusty over the years. These videos are very helpful and I really enjoyed them !

[@swordfish1120]

Do u have a video that shows different tip sizes shot through the same sprayer using the same paint (to show the amount of paint through different orifices and the speed needed to use these tips)? If not, it would make a good video.

[@grubbetuchus]

Excellent exposition, especially on how to decipher tip numbers

[@Garciamrcool]

Thanks, I’m thinking of buying a sprayer and this info is very helpful

[@Alive761]

Thank you! Great information in a tidy package!

[@Gaddman01]

Hey Josh, I've just purchased a Graco 390 and very new to spraying. Would love to know more on spaying. What types of paint ie satinwood, can I use small amounts for doing trim etc. using emulsions and masking up

[@nikolaygrigorchuk5335]

Thank you for information. I have CRACO Magnum X5 TRUEAIRLESS, which tip I should use to paint kitchen cabinets?

[@mikelawwwrie]

If I'm spraying spindles that need priming, what tip would I use for the primer?

[@saudinhodzic3672]

What is the best tip to use for kitchen cabinets using emerald urethane trim enamel ?

[@swiss300173]

Great channel 👍🏻 maybe stupid question but do any make tip fit any machine? Thanks

[@marchandford7787]

Thanks again very helpful. Do I have to different spray caps for the different tips due to the tip seals in the cap? Or is there an easy way to swap them out. Also can you use a FF LP tip to spray emulotion paint on to the walls?

[@alanmcgrath2009]

Josh, can you use a Wagner HEA tip on a graco unit?

[@fernandosalas8589]

The paint manufacturer suggests a tip between .025-.036 which tip I should get I already have 515. Iam new at this thanks.

[@SprayDirect]

Fernando Salas that sounds like a fairly thick product?! Essentially the paint manufacturer is saying you need a tip that ends in at least 25, so a 525 for example. With a tip size that big or bigger, should you need it, you would need to check whether your machine would actually pump this product. What machine do you have?

[@fernandosalas8589]

Spray Direct graco x7

[@SprayDirect]

Fernando Salas the Graco Magnum X7 will support a maximum tip size of .017. I don’t think it will pump the paint you are looking at.

[@fernandosalas8589]

Spray Direct OK thanks

[@fernandosalas8589]

Spray Direct one more thing the paint manufacturer also says a psi of 1500-2000 the x7 has up to 3000psi.

[@djremedy1517]

I have a question, I have some paint that states 0.19 thou minimum for airless sprayer. Can I go lower to let’s say a 317 tip? I’m new to this so just trying to get my head around it 😂

[@roystonpaulmckenzie3878]

Wht is 413 tip good for??

[@tribulationprepper787]

CAN I APPLY THICK DECK PAINT using an X19 and an available spray tip? Thanks

[@Добродій29]

Thank you for information

[@davemedley3128]

Nicely presented. I'm spraying kem aqua waterborne laquer with a 310 fflp tip. Graco. 495.Does 1400 psi sound about right for cabinets? The data sheet says to use 12 to 15 tip but I was afraid of a rougher orange Peel look. What do u say? Thanks.

[@SprayDirect]

Dave Medley thank you, really hard to say as there are still a lot of variables. What I’d do is get a bit of scrap to practice on. If you haven’t check out the video on setting up an airless unit 👍 hope this helps- How to setup your Airless Paint Sprayer kzbin.info/www/bejne/ooW4i6prhd2bmLc

[@PedroHernandez-ou5wy]

What tip I should use for paint the walls of my room I just got the TC PRO sprayer cordless your advice will help !!

[@stevetryit]

5-15 is the most standard

[@dsbelanger]

Well done!

[@alextrading3856]

thank you

[@ProfessionalPainterDecorator]

nice video: Question. if using the 414 tip you mention and its too big and you go to a 210 (not a 214). would you thin the material a little bit more to aid in the flow of paint through the smaller orifice?

[@SprayDirect]

Philip Beckwith yes quite possibly, If you want to spray it neat I would try that first but you may have to thin.

[@_Common_Logic_]

I'm looking to reduce (control) my paint output in order to spray the INSIDE of kitchen cabinetry without sagging the crevices and corners... I'm using an industrial waterborne clear over a previously applied tinted primer. My titan sprayer shoots at 1700lbs max but I'm hoping to choke that down a bit. What tip would you recommend?

[@17N.]

309 I believe would do the job just fine.

[@TheJpassarella]

What tip would you recommend for a stain instead of paint

[@SprayDirect]

TheJpassarella what are you spraying on to?

[@christopherwilson8473]

What tip to spray a door and trim

[@ThekiBoran]

What are you spraying?

[@franklingrebbo]

awesome info, thank you

[@Puppygirl-hj1tn]

Awesome tips. Pardon the pun

[@jabaralanzi9849]

👍👍👍👌❤️

[@LiaqatAli-ro5dm]

We need just tip size number not only sambal

[@mikimiki195]

My F(king head is pinning sounds like they’re all the same 🤯

[@zeetrain9625]

They should give these to all of us who own and extension, not have to pay over $100 for a damn valve..

[@RajeshKumar-gm9ee]

Rajesh