How to set crossover's and install PRV audio DSP 2.8x

[@chase3cm]

the 6.5 has a built-in tweeter, thanks again for the response

[@txddyfarquh69]

Okay im confused now, so is a Digi.Signal.Processor actually an Active Crossover or is this a DSP with basic Crossover & Eq functions?

[@Countryboy8270]

This PRV DSP is an actual active crossover.

[@chase3cm]

the Frequency Response is 65Hz-22KHz for the 6.5 should i use LPF and if so, around what should it be set at and thanks so much

[@Countryboy8270]

If I was you, id just turn LPF off and it'll be just fine. Unless you have some tweeters I'd just turn it off.

[@GameDrop23]

Nice, I learned a lot . Just one question what’s pink noise for? Does it help with ground loop? I am currently having an issue with that.

[@Countryboy8270]

Pink noise is just a calibration tool, I don't really use it at all, I'm having some ground loop issues as well. Could try running a ground loop isolator, or reground the DSP straight to the battery. You will notice when you turn the gain down on your amplifiers the noise will decrease, you could try lowering the gain on the amp and increasing the gain through the DSP also and see if that helps any. Let me know if any of those options help!

[@crandallsolomon469]

​@@Countryboy8270hey I need a lil help to tune minds

[@littlebastardsracing49]

I have a factory head unit using a PAC loc inline converter I'll need to keep that for the DSP ?And what will control cab speakers? PAC or DSP bass knob won't work on the DSP after word ik that using DSP just for driver amp 1 amp

[@leegriffin9717]

What is the b 124 in the cross over sanction

[@c0uchsl0uch]

Can you go out of DSP to a bass processor or would the processor not be used anymore❓

[@kjata77]

Caleb, does it do time alignment? I've seen contradictory information on that. Thanks in advance.

[@Countryboy8270]

If I'm not mistaken I think it does do time alignment

[@kjata77]

@Countryboy8270 Thx, I found where it does in a round about way but that's the biggy.

[@lirishfokeerah2055]

What if i have a stereo that could push 4V RCA output , could i use the PRV dsp to match 6V input of my amps?

[@Countryboy8270]

If I'm not mistaken you would use a line output converter for that not a DSP

[@lirishfokeerah2055]

I was wondering if it does have this feature in it like audiocontrol ?

[@Countryboy8270]

​@@lirishfokeerah2055the audio control is a line driver and a DSP, and a line drive is made to boost the signal. I would get a line driver if you want to match voltage to your amps

[@jeffgendron1959]

If I unplug the battery does it automatically start back up again with the settings as they were or do I need to load them?

[@jeffgendron1959]

I'm thinking of using this in a boat where the 12v will be shut off for weeks and then turned on on weekends its being used.

[@Countryboy8270]

As long as you hit the save option before you turn it off, you should be able to load the options back up yes

[@keatin1063]

@@Countryboy8270so that’s what happened to my system, duh.

[@santanabori]

How you set up your parametric eq?

[@Clippinispimpin]

6:12 am , install starts will update in a hours or so ☺️

[@Countryboy8270]

@@Clippinispimpin hell yeah

[@Clippinispimpin]

@@Countryboy8270 little late finished a hour and half after this comment . You did the job on makin sure it’s usable for my show ahhh !!! Much love bro would love to show you the build prossecc

[@chase3cm]

what hpf setting should 6.5 midrange speakers be set at

[@Countryboy8270]

I would set it at 120

[@angelnoguera1209]

I don't understand how to set graphic EQ. Input and output EQ I just have my HPF set ......

[@Countryboy8270]

Honestly I would just set your hpf and lpf and use whichever preset you like the most. I use the hip hop preset for graphic EQ, it can get confusing but that's what I would recommend doing.

[@mrkitty3849]

Give me a 7 band inline eq out to 3way xover im old school that thing say to much can go wrong.

[@Countryboy8270]

Yeah I'm about the same way I don't like all the extra stuff

[@johnnybhageloe8904]

Hello cant I use this DSP for subwoofer

[@Countryboy8270]

Yes you can!

[@delroypatrice1011]

How is the bass on the subwoofer

[@Countryboy8270]

Good I don't run the subs on this but you can

[@delroypatrice1011]

@@Countryboy8270 how you did you sub setup

[@vidalfernandezwtb9003]

@@delroypatrice1011u don’t really need this for a sub setup, i recommend an lc2i pro if you’re only adding subs to your system. this is more to tune your vocals and mids

[@delroypatrice1011]

@@vidalfernandezwtb9003 ok thanks bro

[@kalebfreeman0939]

How do u install this?

[@Kid617]

So if I'm understanding correctly how this DSP this eliminates having the need to have a equalizer and a crossover for each amps this replaces everything

[@Countryboy8270]

Yes this will help you get your crossovers and equalizers perfect!

[@Kid617]

@@Countryboy8270 so I still need all that lol i figure I wouldnt need all that thank saved me from buying something more

[@Countryboy8270]

@@Kid617 basically this allows you to set crossovers, equalizers, and gain on the amp without actually having to do it on the radio or actually do it on the amplifier. Allows for more accuracy and is normally easier than trying to do it on a amplifier

[@Kid617]

@@Countryboy8270 this is new I'm under getting a new for each amp and a crossover I thought this would get rid of the need for all that

[@Countryboy8270]

@@Kid617 This does get rid of the need for that, but you only need one of these. This can control up to 8 amps at one time

[@hustlehousemarv3625]

Hey buddy how do you take the bass out the midrange speakers with this dsp I’m use a Taramp Ts 800x4 it doesn’t have a crossover

[@Countryboy8270]

Turn your HPF up, I normally set mine at 100-160hz, the higher the less bass it plays, the lower the more bass it plays.

[@hustlehousemarv3625]

@@Countryboy8270 so I need to turn off the Lpf

[@Countryboy8270]

@@hustlehousemarv3625 no LPF should be set between 6,000-10,000 just depends on the speakers recommendations

[@destineal]

SSP 2.8 looks the same

[@305chevyboysp6]

Hey sit da horns?