The Ultimate Tutorial for Setting Up PRV Audio DSP Features/Crossovers For the Best Sound Quality 🔊

[@williejones8977]

Man this actually helped me even tho the taramps dsp is slightly different but the same I was able to figure my sound out

[@kayone8571]

When you come out of the dsp Do you use one pair of rca or one single lead rca and the n split lead off

[@Gonzy1122]

Hi. Just a question. On the prv for power it says to use atleast a 13 gauge wire with a 1 amp fuse. Where would you pull power from for the prv aside from a fused distribution block?

[@Countryboy8270]

Either directly from the battery itself, or could probably tap into a fuse from the fuse panel on have it come on with the car

[@SlamryCamry19]

Ok so this is the area of my build where I'm currently at and can't figure out what type of DSP I need 4 or 8 channel I am going to have two amps a sub amp and mids and highs amp four door speakers and either two or four tweeters just to start with and learn this being my first build I'm told it's better to have an independent amp for the tweeters but to save money for more expensive things I'm going to piggyback the tweeters like the OEM setup but anyway with just two amps wouldn't I just need a 4 channel like the one in the video I have had a few people say I need a channel for every speaker that can't be right can it

[@Countryboy8270]

So you really don't have to have an independent amp for your tweeters and mids, it definitely helps, but you could just run mids on Channels 1/2 and tweeters on 3/4 you'd just have them on two different channels on the DSP. That way you could control sub amp, mids on one channel, and tweeters on one channel. I always recommend to get the 8 channel just in case you ever want to add an amp. Never know when you want to have more audio 🤣

[@c0uchsl0uch]

I could use this with the 4 outs going to a 4 channel amp powering 4 door speakers, or the same with 2.8 then I would have 2 outs for the sub amp? Well that would be 6 but I didn't see the 2.6 so I just said 2.8, is all this correct ❓ Thanks

[@Countryboy8270]

@@c0uchsl0uch yes!

[@ericshaw7859]

Always go with more channels when investing in a dsp. Four doors = 4 channels when inactive, 6 channels if rears are not components and running active in the front, 8 if rears are components and running active. Then leave 1-2 channels for subs and possibly leave one channel for center depending on the install.

[@zoonthabeat6869]

Get 8 and don’t worry about upgrading.

[@herbwash3139]

Does it really help sub frequencies? I want to just use it for 6-8 high mid speakers only.

[@Countryboy8270]

It does help control your subs but I use it for my door speakers

[@keithmonthy2699]

hey bro sorry to disturb you I need your help to set my DSP... I have a ( DSP Crossover & Equalizer 8 Channel Full Digital Signal Processor (Sequencer).. and I have 4 speaker 225rms 4ohm and Bridge to 2ohm.. can you explain to me how to set my DSP properly please

[@SpinningwrencheswithJ]

Do you have to set all the adjustments again when you remove the battery? Or if the vehicle’s battery dies?

[@Countryboy8270]

@@SpinningwrencheswithJ if you go to save on the DSP, it'll let you save everything, and if you remove the battery or something happens you just go to the load feature and load everything up

[@SpinningwrencheswithJ]

@@Countryboy8270 got it thank you 🙏🏽

[@SpinningwrencheswithJ]

So if you leave your presets on flat on dsp, how do you adjust your settings on your radio? Smiley face 😊 ?

[@FinsleysCustomCarAudio]

I might make a video showing and explaining the “limiter” part of the DSP. Seems as if nobody talks about that feature when doing a review. It’s a great feature to use once you understand. Great video though :~) Cheers from, Ohio.

[@jonseeley8263]

limiters are only needed by people who dont know how to set up amp gains/levels , which is a lot of people unfortunately ............recorded music is already "limited" , only really need limiters in live music , with live microphones and instruments etc................. prv is the only company (car audio) to put limiters on there audio equipment , its to correct/protect people who dont know what they are doing............thats about only use for it

[@JoseMartinez-b1k]

Can you still run an equalizer ?

[@Th1sCantBeReal]

hey good video, but it would be amazing if you went into more depth. I just had the PRV Audio DSP 2.8 installed, but the only change I was able to make was switching it from mono to stereo output, which is a little better but not the massive improvement I was hoping for. Whenever I adjust the Graphic EQ, no matter what settings I change it to, I cannot detect a difference in the audio whatsoever, I'm wondering if I need to have knowledge about my amp and how much power is being used and all this, but I just had all my components installed for me and I dont know anything about my setup. Right now hip hop music sounds passable/good but rock/hardcore or anything with atmospheric guitars is clearly not as crisp as it needs to be.

[@Countryboy8270]

@@Th1sCantBeReal so I have a gain setting video on page, and I'm about to do a crossover video also later this week. Just gotta play around with the presets and really find out which one you like the best. But setting your gains and crossovers correctly will definitely help improve sound quality

[@Th1sCantBeReal]

@@Countryboy8270 Thank you.

[@VenganzaCayey]

Equalizer does a lot more to this

[@islandbikers8027]

What’s up, bro? I have PRV. DSP having a little trouble how to tune it. Can you help me please Twitter 6 1/2 speaker two 10 all PRV speaker

[@VenganzaCayey]

What 10” mids are you running in 10k htz

[@Countryboy8270]

Ds18 neos

[@austinxb]

How did you run your bass knob with a dsp did you run rca to dsp then amp to knob?

[@focused313]

depends on the type of bass knob. If it's inline (with RCA), then put it in line between the DSP and the sub amp. If it's an RJ11 (I think that's what it's called -- the telephone type connector), that plugs straight into the amp, nothing changes.

[@saolelejrsaolele7271]

Do u need 3 fuse?

[@briannash7960]

So can u set the hrtzs to say 20hrtz, and it'll make the subs play that low?

[@Countryboy8270]

@@briannash7960 honestly it just depends on your box how low your subwoofers play. I would turn off HPF for subs, I play mine down to 18hz no problem

[@briannash7960]

@Countryboy8270 thanks brother, I built a box that was in the owners manual that came with the subs that they recommended gave all the sizes and deminsions so I went with that and it says that particular box is tuned at 30hrtz

[@Countryboy8270]

@@briannash7960 yeah it should play down in the 20s and into the 30s well, I would have recommended around 30hz tuning

[@KorawitKaewyom]

Hi i have a question. does dsp remember setting if remove it from battery for all day?

[@Countryboy8270]

Not 100 percent sure, but there is that save feature you can use and it saves your settings and just load them just in case

[@KorawitKaewyom]

@@Countryboy8270 Thanks a lot sir 🙏🏻

[@angelnoguera1209]

So you're suppose to set HPF and LPF for each speaker? Wouldnt you only set HPF?

[@Countryboy8270]

If you want it to sound the best yes, most radios only let you set HPF, you can get away with no LPF but I'd recommend setting both.

[@angelnoguera1209]

@Countryboy8270 can you please explain how to set graphic EQ, input output paragram. I get it's to cutt out or boost frequency but I'm not 100% sure what to set the frequency too...

[@jonseeley8263]

@@angelnoguera1209 ..........you just set it to what ever sounds good to you..................unless you have an rta freq measuring device , which nobody has now-a-days............its all hobby grade audio equipment.............just play with it until it sound good ..............only thing you can do wrong is have clipping (distortion) (red lights flashing)

[@jonseeley8263]

say you have a subwoofer that can play 30-100hz............. set your HPF at 30 , LPF at 100...........if you set at 20 and 200...........its just wasting power because subwoofer cant PLAY BELOW 20 OR ABOVE 200......understand................same with midrange............HPF=100 and LPF=3000 (example)...................same with tweeter HPF=3000 and LPF=18,000 (example)............look at your speaker specs to get the idea

[@Countryboy8270]

@@jonseeley8263 bro subs play below 20 Hz what are you talking about 🤣

[@saolelejrsaolele7271]

How you connect your dsp to the back??

[@Countryboy8270]

Just run positive, negative and remote wire. You can use a fuse if you would like

[@1sthawaiian11]

Bro i wonder how you set your subwoofer?

[@Countryboy8270]

I would just set your LPF at 60 or 80hz and it should be perfect

[@puertorockboxinggym5771]

💯💯💯💯

[@jasondeak8667]

I was excited when I seen this video because there isn't much out there. after watching I was disappointed, you didn't really explain much, you show what you have your set on but for example the gain, you can't just petit on 10 and expect it to work with everyones system< how did yogurt to the -10 setting, by ear? or by using a tool as oscilloscope or and meter? you have to set baed off where does your system clip, and maybe I'm wrong but you didn't even sy where its set on the amp itself, all the way up and then use your dsp? you need to st it on your amp using such tool I motion and then fine tune it on dsp or, for this you need to find where your headhunt clips, then you can set your gain on amp, then make sure it not clipping when your turn uo to volume on head unit at your lipping point< if you are then adjust gain on dsp, I was really hoping you went into detail on what someone the setting are like the perimeter input and out put, limiter because I can't find video on that info and I don't know, id like to know what its actually doing when I change settings. oh and if you use the presets on dsp then you don't need mess with anything because it just did it for you don't go and adjust everything then pick a preset as all your custom setting go away. dsp and using preset is silly to me but I'm not professional ,I'm just self taught from installing my own system after paying to have it done wrong. not trying to hate thanks forsaking your time to do video, just be more educated on it or do better explaining stuff if you are educated, sound like a dick but not trying to be

[@Countryboy8270]

@@jasondeak8667 I understand bro, I should have went into more detail but I honestly just wanted this video to be a overview of the DSP before you actually buy it. I can make a follow up going into detail with the gains, and limiter and some of the other features. I honestly set the gains really low because the mids and highs are to loud for me each door is on a 5000 watt amp 😂

[@jonseeley8263]

worst explanation and set up of this device.................."para" means parametric eq filter , not parameter............the remote outs are for turning on your amps "in-sequence" to avoid popping noise........................on and on...............this guy is a beginner....................dont listen to him.................read the manual you will learn 1000x more ........................BT24 means "butterworth" 24db/octave................butterworth was the electrical designer who invented the filter ................this guy should not be doing videos ......................he learned from the street , which is wrong............50% wrong info sprinkled with a little BS

[@Countryboy8270]

Bro don't come on my page posting negative Shit, you can make videos too but you choose to comment on other peoples stuff. Most people will never use the majority of the things that a DSP is needed for. I use my knowledge to help people and learn everyday, I don't know everything but I also could care less about mids/highs

[@jonseeley8263]

@@Countryboy8270 ..........its not negative.......im just telling the truth........you dont really know what you are talking about...............maybe you should go read the manual.............countryboy

[@justinhaire7888]

Not understanding those filters can burn things up quickly. Don’t take it as being negative. Use it as constructive criticism and improve your knowledge to help your viewers. There was a few definitions between this video and the 2.8 video that could go the wrong direction for people. The more you learn the more they learn equaling better and broader fan base

[@angelnoguera1209]

​@@jonseeley8263what should you set it too? I need help