Must say though.... I have thought that your series is the most complete! I personally just ripped my gen 2 apart and i reference your vids very often. Excellent work mate!
@DIYwithMichaelBorders2 жыл бұрын
If interested in purchasing this product, visit our Amazon affiliate link below. I earn from qualifying purchases. amzn.to/3G1aDLl 1. CDI inch pound torque wrench tutorial review kzbin.info/www/bejne/Y3m5optqd6xjr7c 2. Separate Mercruiser outdrive upper from lower unit kzbin.info/www/bejne/qYurdYyracqYbNE 3. Remove U-joint gear bearing assembly from upper unit kzbin.info/www/bejne/fIDIqoeIZp6Gjrc 4. Build assemble outdrive upper unit stand kzbin.info/www/bejne/nX2lgqmgnr6Ue80 5. Best outdrive lower unit stand - assemble review kzbin.info/www/bejne/i3bTqIWkntKApcU 6. How to assemble 6ft Craftsman workbench kzbin.info/www/bejne/oF6ofn-qYr9kebM 7. Adding drawers to workbench kzbin.info/www/bejne/mJScnYGkjbqfqaM 8. How to install Swivel Vise onto workbench kzbin.info/www/bejne/aKW2fouCqr6Jodk
@kidrocking79 Жыл бұрын
Hey Mike... I think you may have overloaded the bearings with 61 in-lbs of force. That wrench you are using is newton meters.
@golfwins1974 Жыл бұрын
I wonder if he saw this comment. Seems like you are correct.
@BradCook-fe7nu Жыл бұрын
I was about to order this torque wrench and realized yes he is referring to inch pounds but the dial is showing newton meters. This would not be a good wrench for this project.
@richardtucker5425 Жыл бұрын
You mentioned on the slip fit that the nut gets torqued to 80 pounds. Is that foot pound, or inch pounds? If this is the procedure, then why even buy the special nut and washer if the old bearings and gears are being reused?
@steveingram27732 жыл бұрын
Great Vid Thanks
@MikeSsuncoasttrains2 жыл бұрын
I installed a used good set if bearings and gears in my alpha one 1988. Now it whines . I did not do this preload. I did not use a torque wrench . I could turn the shaft with my hand prior to installing. Can'timagine it's too loose??.
@DIYwithMichaelBorders2 жыл бұрын
Thanks for watching. It’s possible that it’s due to the preload being slightly off. Improper re-shimming for the change in gears and bearing can cause this.
@MikeSsuncoasttrains2 жыл бұрын
@@DIYwithMichaelBorders I used the shims that were in it already. Gonna pull the drive.
@DIYwithMichaelBorders2 жыл бұрын
@@MikeSsuncoasttrains Keep us posted. Do you plan on performing preload procedure?
@MikeSsuncoasttrains2 жыл бұрын
@@DIYwithMichaelBorders I think It's coming from the gear set. The lash looks good and it doesn't even get warm.
@DIYwithMichaelBorders2 жыл бұрын
@@MikeSsuncoasttrains Awesome, looking forward to hearing back from you. 👍
@dhrarend-janvanbulzen8468 Жыл бұрын
Jou forget the clamp in the middele of the bearing 🤦🏻♂️
@DIYwithMichaelBorders Жыл бұрын
Thanks for watching, it’s recommended to do so however we didn’t have a clamp readily accessible. Keep us posted on your project. 😎👍