How to set timing on MegaSquirt

This video details how to set the timing with a basic trigger/edis setup and a toothed wheel.

[@michaelkarlsson5969]

This is the best tutorial on setting base timing i've seen yet Thank you

[@Grainsauce]

Fantastic video, I just wish you had more megasquirt videos, excellent teaching.

[@tricarbproductions8463]

Thank you!!… your description is great … you don't get bogged down showing a bunch of irrelevant material!...thanks!

[@BCaldwell]

Super informative stuff man! Good to see you uploading again...

[@Bville99gt]

Great info... Thanks for the videos

[@jasonlrusk]

Well detailed thankyou. I found trigger Wizard under tools

[@BlackFoxEFISupport]

You are likely using an older firmware then, be sure you are using the newest firmware for MS2 its 4.3.2 with a 4.3.3 in beta

[@robertelmo7736]

Well, my buddy with megasquirt experience said to get my car set to to 20 degrees...I had the intake off/distributor off (SBF 351W) and I put the distributor back in and got to getting the 20 marked on the balancer to set it to. IT WAS DEAD ON 20 without even loosening the distributor. Then I said I will try to do it then have him double check me, so I searched and got here and BFT says set it to 20. Then the trigger decoder opens and has "20" on it. Nice. Rather be lucky than good any day. Remember to set back to table or you will be stuck on 20 degrees lol. I have to say it would be a lot easier to be able to pull the spout and not have the timing jumping around at all when you set it. Could just plug the real base timing in and be done, but that might be a Foxbody thing. Anyways, I am pretty sure it won't run with the spout out anyways.

[@awhitness]

If I install a new distributor. Set Fixed timing at 20deg. With my trigger wizard at 0.00. Let’s say it reads 5deg at the balancer. I can’t just turn the distributor until I get 20deg? Then fine tune it with the trigger wizard? Thanks for all your knowledge and vids.

[@e34boat88]

so the first tooth after missing tooth is number one tooth, but i start counting on the tooth 2?

[@1489mustang]

Thank you for this tutorial. I wasn't aware I can adjust it like this. Can you help with warm up enrichment? My Mustang runs like garbage until it hits about 145 degrees.

[@BlackFoxEFISupport]

Of course, WUE is simple to tune. When the engine is cold it will need quite a bit more fuel, try and set the WUE so that the AFR is 1 to 1.5 AFR richer than your normal idle AFR. In order to give you a better response I will need to see exactly what the engine is doing. you can email me at [e-mail] with the tune and a datalog along with a description of the issue

[@justinlogue31]

I inherited the mega-squirt have learned a lot but still a lot to go. I have a now good running car but I had to remove the distributor to re-clock it to make room for the big fuel rails. While running the timing light is showing -10 and the computer screen was showing +15. So If I follow your steps to get these to numbers to align them selves again I am good to go with out worrying about turning the distributor any? Thanks!

[@BlackFoxEFISupport]

If you are reading -10 with an offset of 15 then you have 0* of mechanical advance.. assuming a locked timing value of 20* for every 1 degree of offset you get 2* on crankshaft. Larger offset values decrease timing at the crank. set your offset angle to 10 and adjust the distributor. However some prefer to run an offset value of 0*.

[@justinlogue31]

@@BlackFoxEFISupport When I got those readings I didn't know to lock it at 20*. Now I do so I am going to re-check it before I move anything.

[@406_chevelle8]

What's your knowledge on a small block chevy? I have a two wire dizzy locked out with a phasing rotor. I have it set with a base timing of 10, my trigger offset is 10. I turned the dizzy untill the fixed timing matched the balancer, any amount of throttle it pops out the exhaust. I cant find ANY information on how to do a simple sbc setup properly

[@stevenvanorder449]

Sounds like you have a rotor phasing issue.. check your trigger for proper edge. sounds like you may be triggering early and when the advance comes in its firing the previous cylinder. you can email me at [e-mail] for more help

[@mohdlx4025]

why you can not just copy the number comes from timing light into to the fixed field and discard the offset ?

[@stevenvanorder449]

In a basic trigger mode the offset cannot simply be discarded, that is what the base timing is set too. You also have to take rotor phasing into account, 360* of rotation /8 gives you 45* of rotor movement across the distributor per cylinder. We want to make sure we dont cross fire from one plug to another so we have to trim that down even further so we dont get scatterspark. lets say we have 35* of useful movement of the rotor but it is likely less. This is a narrow window to work in, The base timing is the lowest value that we can command. So if we discard the offset it will limit the amount of advance we can run or it can cause the maximum advance to be limited. You have to have the distributor somewhere in the 0-20* range for base timing, The ecu will accept this just fine. However with any installation the rotor phasing needs to be checked. by using a base timing in the 5-10* range you will fall safely in the range the distributor was designed for.

[@finalzodiac3622]

my timing for fixed advance is set at 12 in the software and i read 12 on the balancer i assume im good?

[@stevenvanorder449]

Yes you are good to go.

[@richardrockwall8879]

Hey black fox. Do you have an email or something. I have a couple of questions. If you're cool with that

[@stevenvanorder449]

[e-mail]