How to Set Up Your Home Power Backup - FULL-LENGTH VIDEO

[@davesarmanian175]

Bought this great generator a little while ago. For the record I really like it! Works great and powers the entire house during a power outage. Obviously do the math and figure out what you want to use during a power outage. However, the only issue I want to report is you might need a bigger gas meter to use a natural gas connection to fuel your generator. Also recommend adding up all of the BTU's you plan to use during the Powe outage and then make sure your gas meeting can handle the additional 225K BTU's for the generator. So, if you buy the generator and it will not start on natural gas, call your gas company and get a bigger gas meter. Once I upgraded the meter the generator started up on the first crank. Best of luck!

[@DuroMaxPower]

That is great advice! Depending on the location/municipality a larger gas meter may be needed.

[@blh3741]

Great tutorial for all the required steps/trades needed to install. Actually, it's the best one I have seen to this date. Kudos!

[@DuroMaxPower]

Great to hear!

[@jasonhildebrand1574]

@@DuroMaxPower I'm only halfway thru the video, and YES, this is a great video that covers everything and it is well done. There are obviously a few minor things here and there, but those are just nitpicks, from an OCD guy !

[@rwstarke]

The cost is higher but using a soft starter is better than a hard start and will extend the life of the outside unit. Also turn off some of the high amperage breakers and turn them on gradually after the generator power is running into the panel.

[@DuroMaxPower]

Hi @rwstarke That is always good advice!

[@rrrr6863]

Lol was about to leave this comment. The in rush current is instantaneous and that meter he used is not able to detect the momentary current that the AC condenser actually pulls. I would guess it still has an instantaneous in rush of at least 40 amps, but it could be up to twice that. Micro Air East Start is the way to go and I have installed several, the other big bonus with soft start is that it will actually give your condenser a longer life as well 👍

[@jamesdavison6394]

yeah i dont understand why a start-assist is not a common feature of All ac units - would prevent the brown-out & system stress that happens several times a day in the hot months

[@jamesdavison6394]

@@rrrr6863 yup. that locked rotor amperage is probs closer top 70A

[@rrrr6863]

@@jamesdavison6394 Probably because the manufacturers don't want people's AC to last longer than they already do. Hell, a good system should last you between 10 and 15 years. That's not a lot of turnover 🤷‍♂️

[@Mr-Chris]

Wow, great video especially detailed on how to do the gas hook up. I did this install 3 years ago and wished this video existed. I know you're supposed to say call a professional, but it's totally a DIY job if you have the right tools and knowledge. This video did a great job explaining it. I have a xp12000eh modified for natural gas, a interlock 50amp inlet, quick disconnect on my gas meter, and a hard start kit on my hvac installed all by myself. I prefer this model generator as it's made for Tri-fuel out of the box vs modifying a Duel fuel to work as a Tri-fuel by installing a regulator.

[@harleybodden1938]

What tonnage hvac system do you have?

[@chuckv978]

I have the 13000eh and was looking into modifying it to Nat gas. Found a few websites...but...how did you do it? parts?

[@Mr-Chris]

@@chuckv978 I did a video on this a few years back, keep in mind the 12000 is different than 13000, but the concept is the same. kzbin.info/www/bejne/eX-9eqxsgtupZ5Y

[@DuroMaxPower]

That is awesome @mr-chris. Do you happen to have videos or photos you could share and tag us in?

[@Mr-Chris]

@@DuroMaxPower I sure do have Videos kzbin.info/www/bejne/l3jRoGmvfr5ogqs & kzbin.info/www/bejne/eX-9eqxsgtupZ5Y . I made sure to tag you in these videos

[@jeremyoliver6858]

Just added a microair flex start to my 4ton heat pump unit! Starting amps went from 79amps with a Klein multi meter down to 24.9

[@DuroMaxPower]

That is awesome! Allows for a lot more flexibility.

[@dudleypotter7491]

Great video,I'm going to purchase a stand-by gen for our home and this explained the installation perfectly. I'm not that handy , so I'll be contacting professionals to do the install.

[@DuroMaxPower]

Hi @dudleypotter7491 Make sure you send us a picture of your DuroMax setup!

[@yourmanstan]

very impressed with this video. whether hiring or diy, this helps home owners know exactly what is needed

[@DuroMaxPower]

Thank You!

[@TheYellowFlashLight]

Wow. Very complete video. Very useful. At least I know how it works (Still hiring professionals for this 🤣)

[@DuroMaxPower]

Glad you enjoyed it!

[@radiotvshop]

Perfectly mentioned steps for the whole procedure . Make sure you have the tools, materials and knowledge to attempt this modification

[@DuroMaxPower]

Well said! We always recommend consulting with a licensed tradesman or inspector to ensure everything is up to code.

[@smithn.wesson495]

A very good general overview of the process to convert a home for using a tri-fuel generator. Of course, every state, local and city building codes will be different. Considering this work requires multiple utilities (gas, electrical, etc...) hire a professional contractor to complete this work. This video used 3 different men all from different contractors for a reason. This is not a do-it-yourself job for most people. Be safe, be smart and do it the right way.

[@DuroMaxPower]

Hi Smith! That is great advice - thanks for the input!

[@alangarcia4411]

I agree! I work for a gas utility and know just enough to be truly dangerous - lol. I would never attempt this as a DIY project. Think of the contractor cost as insurance to help you safely manage a power outage.

[@richlikeg3722]

Paid a plumber to do all the connections and I can tell they ripped me off. I was doubting if I could do it but I did not see any videos at the time showing the process such as this. Seems very doable as I’m very handy. Good to know.

[@markgutierrez9295]

Don’t feel bad. Doesn’t a licensed plumber have to do the job? Mind if I ask how much they charged you? I need to get this done too.

[@rhpham2]

@@markgutierrez9295 ran bout 50ft mainly straight run and was given a bill of $1300. Should had just told plumber to tap to gas line and add a valve then I can handle rest but all hindsight now

[@markgutierrez9295]

@@rhpham2 got it. Thanks for the update.

[@DuroMaxPower]

Thanks! If there is every any other questions we are always happy to help

[@rwstarke]

When I bought my new house, I had the builder add a natural gas line to the back porch which I use for my tri-fuel generator/BBQ. During the Texas Freeze I was running the generator, gas furnace and gas cooktop without a problem.

[@azimsunesara7240]

I'm an HVAC business owner in houston. You need a soft start kit for your AC. Hard start kit helps but Soft start will dramatically decrease your starting amperage.

[@DuroMaxPower]

Thank you for the feedback!

[@phucung2678]

What is the difference between Hard start and Soft start ,which it save energy To reduce the cost of electricity bill during a summer month

[@azimsunesara7240]

@@phucung2678 hard start kit is like a jump for you compressor. it helps you compressor turn on. I usually install this on weak compressors that are having trouble starting up. Soft start kit slowly starts you compressor giving you reduced starting amps. Therefore you can connect a Generator when needed and run your AC.

[@mitchmintz111]

Great video! I wouldn’t put the generator on the curb for easy pickup. It might walk away in the middle of the night. REM to derate wattage output when running on nat gas or propane.

[@DuroMaxPower]

Great point!

[@johnherrera7551]

It was just for this video. It was going to the backyard.

[@Willy12927]

Great video. Tri-Fuel generators are the only way to go.

[@DuroMaxPower]

Yes they are!

[@tdyrkacz]

Why no tri-fuel inverter generator yet?

[@blackphenomenon]

I have a Duromax Dual Fuel 12000 W - I'd not used it until Hurricane Beryl hit Houston. It was brand new, and followed the start up instructions. When I plugged it into my house's interlock kit, and I started turning on a few breakers, inside I could smell burning. It fried many of the electronics on the lines I turned on. After the hurricane I had everything tested. It turned out the Generator was only putting out 153 when it should have been 240, causing the surge I'd experienced, frying many of the items in my house. Please test these before hooking it up to your house. Now I have a huge paperweight because I won't cause tens of thousands in damage to my house again.

[@DuroMaxPower]

Hi There We would like to hear more about this. Can you please reach out to us at [e-mail]

[@grb3748]

Excellent video. Very professional yet easy to understand. Thank you.

[@DuroMaxPower]

Glad you enjoyed it!

[@nate.leal.]

Great video. Well done. Priceless.

[@DuroMaxPower]

Glad you enjoyed it

[@donaldpreston8256]

A very good and a very informative video thank you very much for taking the time to produce it

[@DuroMaxPower]

Glad you enjoyed it!

[@carlcapello9956]

These professionals make the job of installing the gas line hook up and the electrical 50 amp breaker hook up look very easy but, in actuality, it's not as easy as it looks. You have to know how to do it correctly and that takes some knowledge know how to do it properly. If you think you can do the job, give it a try but, remember to have it inspected before you actually try running it. If you run into trouble, you can always call in the professional.

[@DuroMaxPower]

Hi Carl! They definitely make it look easy with their experience. We agree that an inspection is a great way to have peace of mind.

[@patrickmitchell4134]

I agree. It is irresponsible for a amateur to do this

[@mixalis11111]

The AC service tech did an excellent job explaining - very clear, detailed and organized on his thoughts. The other two guys were agonizing to try follow their sayings. Other than knowing why and how to install a hard start kit, the rest is not comprehended. The electrical section was the worst - I have no idea what he was doing because he did not explain anything!

[@DuroMaxPower]

Hi! Thanks for the feedback!

[@alexromo9091]

I agree the electrical part of it was vague but there are other diy videos that explain that portion a whole lot better.

[@darrylmarsh8252]

Does anyone know what brand hard start he used??

[@bobbygene8274]

Get a soft start. Not a hard start. @@darrylmarsh8252

[@benbohannon]

First time I’ve ever seen wirenuts used in a breaker box (by an electrician). Wooo

[@fillie37d.71]

Great video ! Very impressed with the detail of this step by step video. Can you please share a link to all items used in the process of making this video. Thanks

[@DuroMaxPower]

Hi There! Please check the description for the items shown as well as guideline on other accessories.

[@hienaz723]

Thats great video. Its explain everything i need to know

[@DuroMaxPower]

Thank you! I'm glad the video explained everything you needed to know. If you have any more questions or need further assistance, feel free to ask! Call us at 1-844-DUROMAX.

[@wisdomandknowledge9361]

Thank you for this good and informative video.

[@DuroMaxPower]

Let us know if there is any other way we can help!

[@Angeloduarte86]

It's a great informative video! I just bought a Duromax XP9500iH. My electrical panel has bonded neutral and ground wires. Should I make any electrical alterations to install a 50-amp outlet?

[@DuroMaxPower]

Please consult with a qualified electrician. We do not advise making any alterations to your generator.

[@roxanaquintana8620]

Easy to assemble. Started on the very first pull!!

[@DuroMaxPower]

That is always good to hear - thank you for choosing DuroMax Power Equipment!

[@huttone]

dielectric couplers between brass and galvanized steel?

[@TXMURF]

More then just a few things missing. A 5 ton unit does NOT draw 34 amps at start up. My 3 ton draws 102 amps LRA (Locked Rotor Amps) so I paused the video when you put the cover back on the A/C unit and can see LRA is 131 amps. Yes this is momentary, but the generator is going to see it. Your reduced power supply running on natural gas may not run it.

[@mauriceDur]

My 5 ton draws 48-52 with micro-air soft start

[@DuroMaxPower]

That is what the soft start decreases the LRA down to and is shown.

[@ducare7218]

​@@DuroMaxPowerWell he said it's a hard start not soft start

[@Texanfirst727]

Because you need a soft start on your AC.

[@BRENTMESSINA-x1l]

Regardless of the interlock, you should always turn off your main breaker before ever hooking up your generator, its just best practice!

[@DuroMaxPower]

Agreed, but that is what the interlock reinforces.

[@j.p.4541]

Brilliant video, concise and easy to understand. I do have a question, how much should I expect to pay for an install like this?

[@DuroMaxPower]

It will vary by location however on the high side we would say budget for $2,000 but should definitely come in under that.

[@j.p.4541]

@@DuroMaxPower Great thank you!

[@tabithafranklin8750]

EXCELLENT video!!! Thanks guys!

[@DuroMaxPower]

Glad you enjoyed it!

[@bayt0wn281]

You mentioned its runs in a raceway, after you drilled the hole, what did u insert for the wire to go through, and/or whats the connector on the panel where the wire first went through also, looked like a bushing?

[@DuroMaxPower]

There was a conduit raceway already in the wall.

[@oilhammer04]

Excellent video. Thanks for sharing.

[@DuroMaxPower]

Thank you too!

[@Moondoggy1941]

7:41 The quick and easy way to measure that. 1) Measure from the half way into the threads to the wall and subtract 3" that will put the ell against the wall. 2) If using a bracket measure the bracket subtract 3" from the wall and subtract the thickness of the bracket. The second valve is redundant, remove it, it will cause a flow issue.

[@DuroMaxPower]

Thanks for the feedback!

[@joef1159]

Awesome video learned a lot 👍thanks for video 🙏🙏

[@DuroMaxPower]

Glad to hear that

[@frankm2588]

How come 10 or so years ago I went to to the expense of having a transfer switch next to the breaker box put in when all you have to do is have that interlock on the box? What are the advantages and disadvantages of each?

[@DuroMaxPower]

Interlock advantages are more cost friendly, easier to utilize and allow for the entire home to be ran.

[@mcofield490]

Isn't an inverter generator necessary to protect electronic devices? Almost every product in a home today has a computer board. How is a Westinghouse generator safe without an inverter and does Westinghouse sell a tri fuel inverter generator? Thank look forward to your response.

[@DuroMaxPower]

They are not necessary for electronic devices. While putting out a cleaner signal todays portable, open-frame Generators are safe for most electronics.

[@alanrodgers4156]

I live in Houston with a detached garage and natural gas. My gas meter is located on the front of the house to the left side and my electric meter located on the rear right outside side of the garage. My breaker box is located on the adjacent side of the electric meter inside the garage. My question is do I have to run a solid gas line underground, towards the rear of my house, where I need to locate my generator or can I use a quick connect and connect only when needed?

[@DuroMaxPower]

A licensed Electrician should be able to run an inlet toward the side of the house where the fuel supply would be to save the hassle.

[@moblack5883]

@@DuroMaxPoweryep my electrician told me that today

[@VS-wq4sy]

Great video and very helpful installation of my inlet box

[@DuroMaxPower]

Glad you enjoyed it!

[@hd16539]

I didn’t catch where the white wire was connected to on the breaker box

[@sergetorres611]

what size is the gas hose 3/4?.. I have a 30 amp set up and was going to change to 50 amp set up.. I have a soft start on my ac( awesome) but I have to go to a bigger generator and also a natural gas generator.. I'm writing this while on my 30 amp set up in Htown on day 3 without power from Hurricane Beryl!! Thanks for the video!! all the gas pipes are 3/4 for the hose and set up.. 1x3/4x3/4,?

[@DuroMaxPower]

all 3/4" from the utility to the included DuroMax NG hose.

[@dlpaez2714]

where i can buy the hose and the quick conector ??? i live in houston tx thank you

[@everss02]

I'd prefer a soft start assist on the AC, but I guess a hard start works and is cheaper.

[@DuroMaxPower]

There is always more than one way to get to the finish line whether its hard-start or soft-start, Transfer Switch vs Interlock.

[@bobbygene8274]

Soft start is the way to go.

[@JetFire9]

Why no sediment trap at the quick connect? Seems like it would be a good idea since the generator will potentially run for days and you won't always be out there to look after it.

[@DuroMaxPower]

We always recommend it but unfortunately some places dont make it a requirement

[@JetFire9]

@@DuroMaxPower Well, that's good enough for me. I am definitely going to put one on my upcoming install. I haven't seen any sediment traps at the quick connect at the meter on any of these KZbinr's videos. It's just an extra $10 in parts for peace of mind.

[@jeffnash8537]

Is a 250cfm meter and 125 ft of gas line from the meter at the road to the house enough volume for this generator? Mine is hard to start up but once running it’s ok. Only gas appliance is the kitchen stove.

[@DuroMaxPower]

For the XP13000HXT Generator the required fuel pressure at all load ranges are 6.0 - 9.0 inches of water column for Natural Gas. The BTU requirements are 225,000 BTU at full load.

[@stormyoung713]

Wish they would have shown that in the video.

[@am20093]

This is a fantastic video - thank you!

[@DuroMaxPower]

Glad you enjoyed it!

[@vicentemederos1378]

I am at fort bend county your company can do the installation

[@DuroMaxPower]

Check out www.duromaxpower.com/pages/installer-locator to find an installer near you.

[@vicentemederos1378]

@@DuroMaxPower thank you 👍

[@gspot525]

Excellent video! We'll done!

[@DuroMaxPower]

Thank you! Cheers!

[@ericmartinez5051]

Any recommendations for these services in the north side of Houston meaning Kingwood/Humble area?

[@DuroMaxPower]

Hi There! We recommend checking out our installer locator at: www.duromaxpower.com/pages/installer-locator

[@alangarcia4411]

​ @DuroMax Power Equipment Great video - thank you! Question: at 11:34, the plumber describes a quick connect safety valve - it prevents gas flow even if the ball valve is open unless the hose is attached. I've searched online for that sort of connector but am coming up short. Can you post names of manufacturers and any model numbers? Thanks!

[@DuroMaxPower]

Hi There! We recommend checking Century Fuel Products or MB Sturgis such as this one: amazon.com/M-B-Sturgis-Inc-Generator-Disconnect/dp/B01N6NLDB6?th=1 Please ensure appropriate sizing based off your application. Thanks!

[@michaelh7770]

All the needed quick connect couplings are included with the generator. The female couplings have a poppet that is closed until the mating connection is made.

[@rickymejia48]

Hello where Can I buy the gas hose and the quick connect fittings in the Houston area ? Please advise

[@DuroMaxPower]

Hello... These are included with the purchase of a DuroMax Tri Fuel Generator. However if needed to purchase, please call us at 844-DUROMAX and we can get you hooked up!

[@dlpaez2714]

@@DuroMaxPowerhow long are this hose that came whit the generator???

[@EdwinAragon-n7x]

What natural gas hose is that and where can we buy it

[@DuroMaxPower]

It is available from us at DuroMax by calling 844-DUROMAX.

[@napoguevara6450]

Air Conditioner Soft Starter ICM Controls ICM870-16A Soft Start Controls, Built-in Start the best no no hart star

[@DuroMaxPower]

Yes using soft start and hard start with air conditioners are the way to go!

[@ghyo1]

@@DuroMaxPower OK, but which should be used- soft start or hard start?

[@stephenbrown2054]

Very informative. You didn't ground the generator. I assume that is because it it grounded to the house through the extension cord. Is that correct?

[@avflyguy]

Dependes on whether the generator is a floating neutral or a bonded neutral. Most need to be bonded neutral. Should be a sticker somewhere on the generator that will tell you bonded or neutral bonding. If neutral bonded it is very easy to convert it to bonded with a $5 part and short piece of 12 ga wire from any home improvement center, or you can look online an search _bonding plug for generator_ (not likely to find one of those at home improvement store)

[@DuroMaxPower]

Correct, when using the 50 or 30 Amp Outlet on the Generator with an appropriate Generator Cord the unit does not need to be grounded as it utilizes the Home Power Panel ground.

[@smacleod69]

This hurt my eyes. You are better off with a soft start kit for the air conditioner and is there an internal regulator for the natural gas in the generator ?Because I don't see one on the gas pipe itself.

[@DuroMaxPower]

DuroMax Tri Fuel Generators have a built-in regulator for Propane and NG. They do not require an external regulator for NG.

[@harry_hands]

Love the video but not the irritating looping background sound the editors call "music" but I call NOISE.

[@DuroMaxPower]

Thank you for watching!

[@JDEC1]

Nice setup but since that generator is bonded to the frame don't you need a ground rod at the generator when connecting to the service panel though your inlet box?

[@DuroMaxPower]

Hard to speak in generality, however most applications for inlet to panel do not require bonding as the panel is bonded.

[@cdurkinz]

This was excellent thanks.

[@DuroMaxPower]

Glad you enjoyed it!

[@shawnhicks369]

Great video

[@DuroMaxPower]

Thanks!

[@devavilluri]

Hello, thanks for great video. I see you used gas valve "matco norca 600 wog-150 swp" can you please post links to where I can purchase this but more importantly the gas pipe that connects to this valve and then in turn to the generator Natural Gas inlet. Appreciate if you can point me to right place to buy so I can avoid buying wrong items. Thanks

[@DuroMaxPower]

Hi There Here is the link to the valve: www.grainger.com/category/plumbing/plumbing-valves/shut-off-valves/ball-valves/manual-ball-valves?attrs=Max.+Pressure%7C600+psi+WOG&filters=attrs. The above valve and pipe will need to be sized to your specific meter so please measure and then the pipe will be available at most local hardware/plumbing store.

[@devavilluri]

@@DuroMaxPower Thank you for quick reply - in the video there is specific call out to make sure to buy the hose that matches with valve, can you please list the hose that goes with that - as it was stated only those hose inlet nozzle can open the valve and hence a compatible hose should be brought with the item together

[@southernoutdoors1862]

Great video I wish I had seen this before!!! Would have saved me money trying to use a portable for whole house backup power! I have gone through inverter route because of the clean power and sensitive electronics ie computers routers tv etc! So serious question I think the DuoMax XP16000IH inverter is my solution to whole house back up clean power with out having to parallel 2 9k is there a way to convert the XP16000IH from propane to LPG? If there is I will order asap thanks again for this informative video!!!!!

[@southernoutdoors1862]

Sorry for the confusion is there a way to convert the XP16000IH from LPG to Natural gas

[@DuroMaxPower]

There will be a 16,000 Watt Tri Fuel Inverter coming soon.

[@awesomedee5421]

If the generator turns off from too much load, will it automatically stop the gas flow or will that be an explosion ready to happen?

[@DuroMaxPower]

The regulator system in the generator is a "Zero Flow" regulator that will turn off the flow of gas into the engine if it is not running or shuts off unexepectedly. As always, for safety purposes it is suggested to turn off the natural gas supply at the valve installed by the plumber when the generator is not running.

[@boby115]

Not bad but let’s address a few things that may not have been mentioned or overlooked #1 now that a load is being added to the system let’s calculate the total BTUs, including the new generator and determine if the gas meter can handle the total load (this may include a call to the local gas utility to let them know your intentions on adding a load; especially if their computer system is set up for spike load readings). #2 those things on top of the meter are not called unions they are referred to as meter nuts. #3 let’s try to use an adjustable wrench on those service valves, pipe wrenches tend to marr the brass lugs on service valves. # 4 let’s try to incorporate a sediment trap at the generator and hose connection. And #5 it’s recommended that you take gas pressure readings (lock up & working) , this would involve all the gas appliances in the house plus your newly installed generator (running all at once for working pressure).Hope some of this information helps and stay safe out there.

[@DuroMaxPower]

Hi Bob! Thanks for the input and we encourage homeowners to consult with their gas utility company to ensure adequate natural gas delivery.

[@boby115]

@@DuroMaxPower , developing a customer/installing contractor checklist is one of the best ways to stay consistent and put an end to all the “ I thought” comments. Having worked for a full service gas utility for 35 years and now consult from time to time in my retirement, I can assure you keeping all the affected people on the same page is one of the best things you can do. I’m always amazed when I am gathering information for a claims report or sitting at a deposition table, people make statements like “ we never thought to contact the utility“ or “ we don’t have a set procedure, we only have the installation manual“ . Believe me there’s a reason why Airline pilots have a checklist ✅.

[@robsapplianceplus6071]

#6 That is not an inverter generator and therefore not the correct type generator if you plan on using any electronics.

[@boby115]

@@robsapplianceplus6071 , you are correct 👍 and should be another thing added to the checklist. With all the different circuit boards on appliances today I believe these types of generators will be become obsolete one day.

[@JohnCap523]

Actually, when adding gas load, it’s mandatory to inform the utility. That meter is not rated for that load assuming there’s heating equipment already attached. Additionally, the utility should install the takeoff point (tee), not a contractor, at the time they replace the meter (assuming the gas service is sufficient for the added load). Other comments: never apply pipe dope (sealant) to the first two threads; never wrench a close nipple like he did which damages the threads (and yea, that nipple leaked); never turn off the gas supply before closing all inside valves (and turning off any appliances with power to them such as a furnace or boiler or power vented water heater) or else any operating appliances will suck the gas out of the pipes requiring a lot more purging once the supply is restored. Lastly, the “coupler” to the right of the tee Tony installed, is not actually a coupler, but a pipe end protector, and while Tony didn’t install it, it should not be used as a coupler.

[@PhoeNix-gr2vz]

When relocating breakers, it is obvious the wires are cut to the place it wire was set to. (What does 9ne do if the breaker wires are to short at the re location of the breaker?)

[@DuroMaxPower]

Hi There! Since every jurisdiction is slightly different you would need to consult with a local electrician to confirm what would be code compliant.

[@PhoeNix-gr2vz]

@@DuroMaxPower Thank you for you reply. It does make since and since I am not an electrician I will contact a certified one in my region before playing with such dangerous thing. Thanks again

[@jrvane11]

Do you need to cut the neutral wire on the generator in order to go from a bonded neutral to floated neutral condition?

[@DuroMaxPower]

No - we do not recommend altering the neutral on the Generator.

[@datboired832]

My gas is on the opposite side of my house. Im guessing over 100ft, if i wanted to use NG, is there a limit on how long the coord connection can be?

[@DuroMaxPower]

It isnt recommended over 100 ft but you would need to calculate voltage drop on the length of the run you are looking at.

[@joemooskie4444]

Good video, but i installed a transfer switch next to my breaker panel . I can control which room i want powered. I am on propane , so i want to power certain rooms this will conserve on propane.

[@DuroMaxPower]

Glad you chose the option that works best for you! There is definitely more than one way to achieve power independence. Thanks for choosing DuroMax Power Equipment!

[@carmenlena2010]

I never saw where the plumber used the uchannel bracket. Does anyone know?

[@DuroMaxPower]

Thanks for the catch! It is shown at 26:14 as a brace and support for the gas line.

[@bobbygene8274]

He used a section of 7/8" unistrut with a 3/4" "strut strap" to secure the pipe with.

[@marvin6148]

Does your 3/4 inch inside diameter natural gas hose hook up to that generator via a 3/8 inch male flare On the generator? In the video I saw an elbow piece on the generator with a quick disconnect to that three-quarter inch natural gas hose. Where did you get that please?

[@DuroMaxPower]

Hi There! That elbow is included with the DuroMax Tri Fuel Generator.

[@OMY2FYB]

my electrical box does not have a main disconnect, will this be an issue? can i get one added in order to install the interlock kit?

[@DuroMaxPower]

Yes, we recommend consulting with a local licensed Electrician.

[@carmenlena2010]

Where did you find the Start Assist (Hard Start Kit)? The link on Amazon shows a different device with more than 2 cables.

[@DuroMaxPower]

Yes on Amazon, however the model will vary based on the AC unit you are using.

[@desl.1153]

question i have a Druomax hybrid Elite DS 1300 EH DUAL FUEL. If i convert it to natural gas would it power up my Central air and refrigerator, TV and some lights????

[@DuroMaxPower]

We do not recommend converting or altering the fuel system.

[@rickyc6673]

Is it necessary to replace the regulator at the meter by gas company? I heard when u use generator and use natural gas it needs a bigger regulator.

[@DuroMaxPower]

It will dependent on your service line.

[@milesfromthemidwest]

I bought the generator in this video, does it require a pressure regulator on the natural gas supply line?

[@DuroMaxPower]

This Generator includes the pressure regulator.

[@aholmes6612]

Which is better for an inverter generator, hard start or soft start?

[@DuroMaxPower]

Hi There! That will be dependent on your Central A/C. Please check the manufacturer specs to confirm the best unit for your application.

[@johnwilliamson4511]

Soft start. With soft start inrush current to compressor is filtered through a potential relay before it starts compressor

[@johnwilliamson4511]

Thus controlled. With hard start assist additional torque is added inline straight to compressor capacitor to start compressor. It's forced or a "hard" assist and not "soft" or controlled. I'm and HVAC specialist 20 plus years trade in.

[@ljs2001]

Does this generator have bonded neutral? Is that something of a concern?

[@DuroMaxPower]

DuroMax open frame Generators are considered Floating Neutral Generators. This means that they do not have a bond from the Generator frame to the neutral. The ground and neutral are connected together in the stator housing, but since the stator housing is on rubber motor mounts there is no continuity from the Generator to the frame.

[@jbhobbyist9372]

Does your gas disconnect need to be in the horizontal position or can it be in the vertical position?

[@DuroMaxPower]

Either direction will work.

[@ibeecarefree]

What happens if I tap off of the other line and bypass the meter? The meter is such a nuisance 😅

[@DuroMaxPower]

Probably will get a visit from the local authorities soon.

[@HyperSin]

What about the thd damaging sensitive electronics, is there something i can use that wont cost an arm and a leg

[@DuroMaxPower]

With almost a million Generators sold, THD issues are nearly non-existent.

[@porschenut5610]

Why was the start assist used instead of a soft start device?

[@DuroMaxPower]

Same type of device with different name.

[@romanaxle]

No wire clamp on the panel for the 6/3 NM? 🫣

[@nateitscake88]

I have gas but not sure if it puts out enough pressure for the 15000HTX... Anyone know what pressure in inches of water is normal for a gas meter?

[@DuroMaxPower]

It will vary by location and utility however for DuroMax Generators you would want about 6-9 inches of water column.

[@justinhighdesertkeeper9251]

Nice vid. Where is the Capasder kit found?

[@DuroMaxPower]

Hi Justin, They are available from micro-air.com as well as other online retailers.

[@Gergm7991]

The correct web address is micro-air.com 😊

[@DuroMaxPower]

@@Gergm7991 Correct - thanks for the correction Greg!

[@pettypendergrass8596]

I know everything, but i never heard of a start assist. that is the 'coolest' modification.

[@DuroMaxPower]

We think your comment was even cooler!

[@Threedog1963]

Hard start kits help a home AC system even without a generator. We had one installed on a system after the first compressor failed within 5 years. After installing it, the next AC system lasted 15 years.

[@gary-gilbert]

Some videos say that style quick connect restricts the gas flow and will cause your generator not to run properly. I'm not sure if that is true or not.

[@DuroMaxPower]

Ours were all tested with this style and are designed to operate with it. No restriction issues whatsoever.

[@bobbygene8274]

You purchase the quick connect that will support the required BTU flow for your unit at full load.

[@TheBucktowncrazy]

Question I just bought and received my new tri-fuel 13000 generator. Regarding the soft start, I have a 3.5 ton American Standard ac unit. Is the soft start a universal product, or do i need to purchase a soft start that is made by American Standard? Of course, I'm going to consult with an ac tech to install it. Just asking so i can purchase it. Thanks

[@DuroMaxPower]

It will be made by an aftermarket company - usually Microair. It does need to be compatible with your AC unit, but not the same brand as the soft start manufacturer-wise.

[@TheBucktowncrazy]

@DuroMaxPower I have another question. I just purchased and received my 13000 TRI-Fuel generator from yall. I see that the 15000 tri-fuel is being advertised. My 13000 is still in the box with the band wrapped around the box. If I want to send the new one back and pay the difference for the 15000 tri-fuel is that possible??? Thanks

[@craigharrison715]

is a start assist and a soft start the same thing?

[@DuroMaxPower]

Different manufacturers call it different things but yes. We recommend the Micro Air soft start for use with our Generators.

[@terrae3579]

What does all this cost with installation?

[@DuroMaxPower]

It will vary by area however on average we would recommend budgeting $1500 - $2000

[@ronaldnaeyaert3653]

What size gas connection was used, 1/2 or 3/4?

[@DuroMaxPower]

DuroMax Tri Fuel Generators use a 3/4" Natural Gas Hose

[@equinn2005]

Did the generator come with the remote start kit, im looking to put one on mine but cant seem to find one

[@DuroMaxPower]

The only DuroMax Generators that currently come with remote start are our Inverter line of Generators.

[@equinn2005]

So what is the inverter inline type? I have the XP13000HX and I would like to have a remote start for it.

[@jerryvandyke9216]

Are duromax generators available in Canada?

[@DuroMaxPower]

Please check our Where to Buy: www.duromaxpower.com/pages/see-retailers

[@m9ovich785]

The only flaw I saw in this video is the Cable from outside is not properly secured to the back of the Panel Box. The Inlet box on the outside is big enough to allow a Hole in the wall to accommodate a Cable Clamp. Thanks. Mike M.

[@DuroMaxPower]

Hi Mike! You are not the only one - we also caught this on the final walk through. Rest assured it was cleaned up with a clamp.

[@jamesdavison6394]

Lol i noticed right away - i even said out loud "hey man you gonna secure that thing" lololol

[@jasonhildebrand1574]

21:20 For some reason, I thought that this looked like Houston. And then I saw the 832 area code on the electrician's shirt. Go figure !

[@TXMURF]

I was thinking the same looks like Houston, googled Tony's Plumbing, it came up but I'm always worried about a company that I can't find a physical address for.

[@DuroMaxPower]

We highly recommend Tonys Plumbing out of Houston - Their address can be found here: tonysplumbingtx.com/contact-us/

[@Spaceballs30]

Where is the part of the video that shows the required pressure you need at your natural gas connection, testing to verify the pressure is adequate, and then adjusting as needed? That's SUPER important in this application.

[@DuroMaxPower]

Yes those are all valuable steps you mentioned.

[@bobbygene8274]

They didn't cover that step.....

[@ImYourHucklebery117]

In my area, you cannot use galvanized piping as it flakes on the inside clogging any orifice or gas control valve, you need to use black iron pipe and paint it. When you paint the gas pipe, use some painters tape or old newspaper to pritect the exterior wall from paint, not like this plumber. You also never unthread a nipple like that, you can see he deformed it. It is always reccomended to change the gas meter gaskets once they become loose, you may need 10lt, 20lt or 30lt.

[@DuroMaxPower]

Thanks for the feedback!

[@thomasaccuntius9946]

In my area you cant use galvinized pipe for any gas work, it's black iron or others.

[@DuroMaxPower]

Oh thats rough! Whereabouts are you located?

[@VHP7044]

Galvanized pipe should not be used with Nat Gas, Propane, Gasoline, Oil or Diesel Fuel. Only use carbon steel pipe.

[@fearlessfreep]

Is there a link to the hard-start AC kit?

[@DuroMaxPower]

Hi There! Yes all of the items are listed in the description and here is the Micro-Air Easystart www.amazon.com/stores/page/56795066-0CB3-4DDA-8245-9DEFACD860F4?ingress=2&visitId=48e2611b-83be-4fb6-9594-7e18df2d49c2&ref_=ast_bln You will need to confirm compatibility with your AC unit.

[@ghyo1]

@@DuroMaxPower The hard start capacitor described, installed, and tested is not linked anywhere. Was that part of the video a mistake?

[@rupe53]

fairly straight forward production but fails to mention the size of the gas meter, which will be too small about 80% of the time. You'd be amazed at how much gas a gen set needs.

[@DuroMaxPower]

Thanks for watching! Due to the different applications and regions, customers are always advised to check with their local municipality for the most accurate information regarding their utility service capabilites.

[@shaunmccarron8475]

Is that pre meter ?

[@DuroMaxPower]

Never pre-meter

[@donhgr]

First thing to turn off by utility company is electricity and second is the gas when a disaster happens LOL

[@herewegoagain4041]

U do know about the on/off valve at the place matural gas pipe come out the ground. Also there is a main breaker to turn off power feed from power line😊

[@DuroMaxPower]

NG managed to stay on for all affected by Beryl. We do agree power is first.

[@pf5658]

I need this done at my house. How much is this particular unit?

[@DuroMaxPower]

Hi There! The DuroMax XP13000HXT Tri Fuel Generator currently goes for about $2,499 and is available from many of your favorite retailers. Check out our site for more info.

[@terrae3579]

What does this cost with installation

[@DuroMaxPower]

It will vary by area however on average we would recommend budgeting $1500 - $2000

[@mafosa9563]

"Impressive!"

[@DuroMaxPower]

Thank you!