Transform your #HappyModel #Mobula6 by soldering an #ExpressLRS EP2 Receiver
Пікірлер: 38
@peternguyen37322 жыл бұрын
Yes just in time. My FRSKY was starting to annoy me with range !
@user-df8gs6qi3x2 ай бұрын
Здравствуйте, а как забиндить с радиомастер поккет с этим приёмником, спасибо
@paulm16062 жыл бұрын
Great video buddy, i will use this as a base to start replacing my xm+ receiver on my old quads like tinyhawk 2 freestyle, iflight cinebee75 hd etc👍. Thanks again
@CostaFPV2 жыл бұрын
Thanks dude 🙂👍
@oneRella10 ай бұрын
Thank you!
@mariofpvbr27142 жыл бұрын
Ótimas instruções...uma pena q não consigo soldar 😬
@emmanuelmenenedez67372 жыл бұрын
Hi. I tried installing a happymodel ep2 express lrs external rx in mine and cant get the Serial Rx to save in ports on betaflight. When I set it, it just reverts to disabled every time . I have set the Receiver to Serial and Crossfire in the receiver section. Any ideas? I cant even get the soft serial that I want to use to have VTX smart audio on to save either.
@Romanian_Productions Жыл бұрын
The switch to ExpressLRS receiver was a success, but now the video range is crappie. Do you have any idea why this can be? Thank you for the video, was helping me a lot!
@CostaFPV Жыл бұрын
Probably because of the way the board manages the power distribution. Over the years that the mobula6 has been around, happymodel has released some crazybee lite updates, mine is version 2.1 and I had no range problems after soldering the receiver. Maybe your case is one of the old versions. Sorry I can't be of more help than that.
@FPV-Catonsville Жыл бұрын
I'm about to attempt this in a few days. What size wire do you use to make these connections?
@Dimensas9 ай бұрын
Successfully?
@miaowzerz7 ай бұрын
What aio is this I’m planning on getting a mobula and aparantly they swapped the aio to a crazybee is it still compatible with this?
@CostaFPV7 ай бұрын
This is the crazybee from the old mobula 6, the first one released. Crazybee f4 frsky
@miaowzerz6 ай бұрын
ouh ok thanks @@CostaFPV
@rcaddict9558 Жыл бұрын
Hi mate, thanks for vid, i have inverted 1 IR1 , do i ignore that and just use RX1 im sure my elrs is non inverted, happymodel
@CostaFPV Жыл бұрын
Use rx1 for crossfire and ELRS, left the inverted for frsky receivers and any other sbus protocol
@rcaddict9558 Жыл бұрын
@@CostaFPV love to all ,thanks
@Dimensas9 ай бұрын
How did you bind ? For some reason, I'm unable to do that
@CostaFPV9 ай бұрын
Sorry, I dont use the bind Button. I prefer the passphrase
@Romanian_Productions Жыл бұрын
Why you are doing so fast? Thanks for the video!
@CostaFPV Жыл бұрын
Tried timelapse. But you can pause 🙂
@balajiprasad9046 Жыл бұрын
Hi I have difficulty making the solder stick to the pads on FC...what could be the issue?
@ryanjones6837 Жыл бұрын
Make sure your iron is hot enough and try leaded solder as I used to use unleaded and nothing would go to pads or anything. Did you manage to get it working?
@balajiprasad9046 Жыл бұрын
@@ryanjones6837 yes.
@gregdavidd11 ай бұрын
ON the FC Manual it says RX1 and IR1. I assume IR1 is the TX1 pad?
@CostaFPV11 ай бұрын
Nope, use tx-rx, rx-tx, and avoid inverted pads
@gregdavidd11 ай бұрын
@@CostaFPV OK but on the diagram you show there is no TX1 on the FC. Which pad is the TX1 pad on the FC?
@CostaFPV11 ай бұрын
@@gregdavidd look again, ir1 e tx1 are very close each other
Kkkk. Tem q calibrar isso aí. O meu estava marcando mais de 1000 hj. 🤣😬🤣
@Roadking013 Жыл бұрын
What was the little black piece you set the Rx into?
@CostaFPV Жыл бұрын
Dude, I am no longer using that because is too heavy. Using double sided tape. I dont remember where I found 😕
@Roadking013 Жыл бұрын
@@CostaFPV right on. wasn't sure if it was a 3D print part or something. I was gonna use double tape but thought you had something better thanks though!