Very good, nice details here that I haven't seen elsewhere. 1.) SPIN pipe fitting to spread the flux around the pipe evenly. 2.) Form the end of the FLUX into a HOOK shape. 3.) If EXCESS FLUX RUNS DOWN a vertical pipe while heating it, I can carefully WIPE the excess FLUX OFF the copper pipe -> BEFORE applying solder. 4.) Copper turns whitish and flame turns green means it’s ready to accept solder.
@NickTaylorPlumbingLtd2 жыл бұрын
Hi Mika Tala, Love this! Check out our other videos and if you haven't already don't forget to like and subscribe!
@yorkrojas1452 Жыл бұрын
Thanks for the Highlight!!
@Vincerama7 ай бұрын
Another tip, if you are soldering 1/2" pipe, then bend the solder into an L shape at 1/2", solder until the L leg is gone. Same with 3/4". So I guess still use a hook shape, but make a small bend at 1/2" or 3/4" to approximate the correct amount of solder to use!
@FreeFinca2 жыл бұрын
I've been waiting nearly six months for the plumber to turn up, so now I find myself at the mercy of youtube. Found this/you and I'm already to put on my big boy pants. I hate plumbing, always avoided it, but now I'm all out of choices 🤦🏼♂️
@NickTaylorPlumbingLtd2 жыл бұрын
Hi FreeFinca, Love to hear you giving it a go! Honestly its not as hard as it looks, practice makes perfect and don't worry if you put too much solder on, remember the tip of your torch will be hot so don't put that down on the carpet or touch it! Hope that helps, let me know how you get on and if you haven't already don't forget to like and subscribe! 💪
@FreeFinca2 жыл бұрын
@@NickTaylorPlumbingLtd No carpets and I'm a dab hand at a bit of fire related activities 👍🏻
@jonathanevans10646 ай бұрын
Superb tutorial. Comfortably the clearest and most comprehensive that I've seen on KZbin. Great work.
@Timba-w7f4 ай бұрын
I have to change a few half-inch copper pipes. Is it possible to un-solder the elbows, clean and re-solder them? Or is that not practical?
@NickTaylorPlumbingLtd4 ай бұрын
You can clean the pipe / re-use the pipe but cleaning the elbows will be a nightmare so I would recommend just going down the local merchants and buying a couple for the sake of a couple of quid. Hope that helps :)
@richardscott81592 жыл бұрын
Number one thing is CLEAN, Clean, clean, I once seen someone use their finger to apply the flux and it didn't work out well! Yes!, it had pin hole leaks! The oil in your skin will contaminate the solder fitting! I always use a new acid brush on each job, they are not expensive. Also getting the fitting to hot will cause problem too!
@NickTaylorPlumbingLtd2 жыл бұрын
Thanks Richard Scott, USE FINGERS TO APPLY THE FLUX!??? What on earth!? Does he have any fingers left? Im not surprised it didn't work but interesting point about the oil in our skin, I think I'll use your comment in our top comment of the week for our next live chat and touch on these points.
@octaviojabali6981Ай бұрын
Excellent explication sir started using silver solder on refrigeration pipes your video helped me a lot thank you sir 👍👌
@NickTaylorPlumbingLtdАй бұрын
Thank you for the postivity 🤟
@Sgafify3 жыл бұрын
This is actually a great video. You should carry on
@yorkrojas1452 Жыл бұрын
Thanks Great Vid!! Very complete information. Most how to solder videos don't go into the flame adjustment and you fine Sir did!! Thanks
@NickTaylorPlumbingLtd9 ай бұрын
I love it! Thank you! Also thanks for taking the time to write a positive comment
@danoesq22 жыл бұрын
I'd put a little more solder on the pipes. Using an 1/8 of an inch won't cut it on 3/8+ pipes. I heard the rule is 1 inch pipe, 1 inch of solder and so on. Using that little can work, but I wouldn't risk it.
@goochgaming Жыл бұрын
Don't try that on larger pipe
@remodz638510 ай бұрын
That’s just a VERY loose estimation and in most cases will work for 1/2-1” pipe. But it’s really depends on how tight the pipe and fittings are, new vs. reused pipe ect.
@terrythomas79023 күн бұрын
I was thinking the same. Just a tap of solder might look nice, but Id like to see that joint with water pressure inside it. Or better yet, slice the test joint in half and see the fitting wont be completely covered with solder inside
@greenbeginner922111 ай бұрын
Is there any way to know whether it's a solid, leak free joint before applying water pressure?
@Rambojopie5563 ай бұрын
Not really just experience. If you follow al these steps it’s difficult to mess up
@johnphillips53892 ай бұрын
Air test
@terrythomas79023 күн бұрын
Id say his joint in the video will leak. A "tap" or 1/8" of solder isnt enough under pressure
@moeenahmed68532 жыл бұрын
Hi pal. Is best use a damp cloth to cool down pipe after soldering or some plumbers I've seen,, tend to use flux with a brush and cool it down.... What's you opinion on that? with
@NickTaylorPlumbingLtd2 жыл бұрын
Hi Moeen Ahmed, thanks for the comment, In college they teach you not to do this, the reason is because if you cool the solder down too quickly it will fracture and when pressurised it will leak. For me in the experienced world where we need to get on the job, I find leaving the pipe to cool itself for around 2 minutes then putting a damp cloth on works fine, but always be prepared when pressuring the system. Lastly I would not use flux on a brush to cool it down, flux is corrosive and will eat away at the copper over time if not 100% cleaned off properly. Hope that helps and don't forget to like and subscribe if you haven't already.
@RedRupert64 Жыл бұрын
Shouldn't you clean the inside if the fittings as well? How about using flux with tin, it will provide a proper join with minimal solder?
@duracellplus998 ай бұрын
Great video - thank you for uploading. I will be attempting this myself in the next couple of weeks as I am taking on a bit of DIY and having never done this, I now feel a little more confident. Just a quick question - I noticed you dabbed a small amount of solder on the joint - does it easily flow round the pipe and create the seal? Are you able to see the solder? I was going to buy some excess pipe and fittings and do a couple of test runs in the garage to make sure I can get it right.
@Vincerama7 ай бұрын
Thanks for the video! Seems like many plumbers today are turning to ProPress fittings now and abandoning soldering!
@rioboy413 ай бұрын
Nothing like creating future work for yourself! 😂
@lodollar23Ай бұрын
Are the elbows and tees a little loose before you solder? I bought some fittings that feel to lose to me.
@AdamSithebe8 ай бұрын
Good evening, very informative.
@NickTaylorPlumbingLtd8 ай бұрын
Thanks AdamSithebe. Thanks for taking the time to write a positive feedback 🌟🤩❤️
@Ojeramup12 Жыл бұрын
CLEAN soldering, I like that!
@Marky.H4 жыл бұрын
Thank you so much for this tutorial. Your tips have improved my work no end. Im a carpenter so an amateur plumber at best
@NickTaylorPlumbingLtd2 жыл бұрын
Hi Marky, Love comments like this, thanks for the positivity and good work on the carpentry, any trade is difficult to master so good for you, Ive got loads of videos planned so if you havnt already, don't forget to like and subscribe 👍
@Marky.H2 жыл бұрын
@@NickTaylorPlumbingLtd already subscribed my friend... 😊
@stevesteve58342 жыл бұрын
@@Marky.H f
@EonJanseVanVuuren Жыл бұрын
Brilliant demo mate, thanks
@diljitjedi2 жыл бұрын
The number one video to watch I am now ready to start learning to solder going out and buying all the kid after watching this particular KZbin video well done mate absolutely in-depth
@BillTangy Жыл бұрын
So you apply solder to only one spot and that spreads it around the whole diameter of the pipe?
@thegreatergood66482 ай бұрын
Yes capillary attraction makes it run around the joint
@thedurbec9591 Жыл бұрын
Move the flame around the pipe soo you don't have to burn it so bad
@bojack27402 жыл бұрын
Good stuff. I've been doing this for years and never knew this.
@sixehs10 ай бұрын
Great video thank you so much
@NickTaylorPlumbingLtd9 ай бұрын
I love it! Thank you! Also thanks for taking the time to write a positive comment
@electrolatif Жыл бұрын
Oatey 95/5 solder, is it good for soldering aircon piping?
@shawnsmith9512 Жыл бұрын
Tin antimony 95/5? Too weak for high pressure lines. I like to use a fluxless silver solder and have had perfect results for 30 years now.
@electrolatif Жыл бұрын
@@shawnsmith9512 thank you very much for your reply
@bewseybill36913 жыл бұрын
Excellent. Very professional.
@londonmick86452 жыл бұрын
Absolutely brilliant 👏 great video mate first time watching your content, very well explained and very detailed keep them comeing 😊😊
@NickTaylorPlumbingLtd2 жыл бұрын
Hi London Mick, thanks for your kind words and taking the time to write a nice comment. If you haven't already please like and subscribe to my page as it really helps.
@wemcal3 ай бұрын
Great video and great information
@shawnsmith50282 жыл бұрын
Hi Nick! When you do the professional solder, it looked like you used just a very small amount of solder (less than 1/2 inch). Is this true? Curious because the rule-of-thumb is to use 1/2 inch solder on 1/2 inch pipe. Which is more important: 1. Create ring of solder around joint with minimum solder (less than 1/2 inch), or 2. Create ring of solder around joint using full 1/2 inch of solder? Tia!
@dontcomply50082 жыл бұрын
I noticed this little bit of solder as well. I'm an apprentice plumber and the plumber I work for, and every other plumber I've seen solder copper, use more solder than that. I mean it isn't much more but I would say its about a half inch or so for each joint. And a little more for 3/4" pipe and so on.
@shawnsmith50282 жыл бұрын
@@dontcomply5008 - thanks for the info! I'm a DIYer and I can't afford any mistakes as I live on the 2nd floor of a condo.
@dontcomply50082 жыл бұрын
@@shawnsmith5028 damn! Well just remember to cut the water off to the building !!!
@truthseeker77942 жыл бұрын
Yes this is the professional way to solder. I often watch so called professional plumbers on YT and it's amazing how many of them totally plaster the joint with solder. Many of them also plunge the solder into the flame so as to melt it. You heat the joint and then offer the solder up to the joint. This guy is rare.
@robertmay5392 жыл бұрын
@@dontcomply5008 p
@williamprice59703 жыл бұрын
I have been really struggling with soldering but as soon as I kept the heat gun strong rather than the recommended low heat it was easy. Why is this? I started a plumbing course a month ago and they recommend a low heat.
@dontcomply50082 жыл бұрын
Maybe you just learn different bubba. My grandmother used to cook everything on the highest heat on the stove and still her food was better than everyone else, and no one knew why!
@davidgregory3643 Жыл бұрын
I thought your ment to deburr the inner part of pipe
@JayEm75162 жыл бұрын
Thank you, this was really helpful for improving my technique 👍🏼
@ScottyDog3452 жыл бұрын
I use laco.only ever used that flux once before
@Benzknees2 жыл бұрын
Why don't most plumbers use solder ring fittings? Is it just down to cost?
@ScottyDog3452 жыл бұрын
I start on my pipped first to make sure that pipe inside that fitting is hot enough to take the solder.Then I apply the heat to the opposite side of the fitting that I am applying the solder to.This my friend guarantees that when that solder goes up that pipe and up the fitting everything is hot enough for that solder to equally go both on pipe and fitting in a u inform manner .one drop of solder one snotty drop I had to rip my pipework out.Park lane 1 job .Ask any plumber on there.
@missismiggins73292 жыл бұрын
A+ for the audio! Didn't notice anything about deburring either.
@NickTaylorPlumbingLtd2 жыл бұрын
Thanks Missis Miggins for the comment, I’ve since upgraded my Camera to an 4K ultra HD just for your viewing pleasure so check out my other videos and if you havnt already, don’t forget to like and subscriiiiibe! 👍
@virlanionut2 жыл бұрын
once you put hot water in the fittings they will leak from expansion, you need way more solder
@NickTaylorPlumbingLtd2 жыл бұрын
Hi Lonut Virlan, thanks for the comment, I’m pleased to see your thinking ‘outside the box’ when it comes to expansion and contraction, I’ve been doing it this way everyday for the last 9 years and never had a problem.
@steviedickson47362 жыл бұрын
You almost lost me because the volume too low. Went back and watched with my volume wayyy up high so I could hear. NICE INFORMATIVE CONTENT!
@NickTaylorPlumbingLtd2 жыл бұрын
Mr Dickson, Thanks for the constructive advice, Ive recently upgraded my KZbin studio and have much better quality 4K HD camera with far superior sound quality, Just for you I'll do a new video about this in a few weeks time! Check out my channel and If you haven't already, don't forget to like and subscribe!
@pashtoons2970 Жыл бұрын
excellent video. thanks for the tips.
@honolulu14762 жыл бұрын
What kind of brush do you use to flux ?
@NickTaylorPlumbingLtd2 жыл бұрын
Hi Honolulu 147, thanks for watching the video and taking the time to comment. Realistically you can use any type of brush depending on whether your a DIY’er or a professional aslong as you get the flux on the copper pipe. Try searching flux brush and this will give you some suggestions. Hope that helps and if you haven’t already don’t forget to Like and Subscriiiiibbe!
@Ste20232 жыл бұрын
Great video. And advice
@Rocket-x9v2 ай бұрын
Completely wrong, that's not enough solder at all. First thing they teach you at the plumbers pipe fitting union is you should use 1/2" worth of solder for 1/2" pipe and 3/4" solder 3/4" pipe ECT. I love it when people watch these plumbing videos and do what the person tells them on the video and then they call me out and it ends up costing them double. Because they have a leak at every joint.
@NickTaylorPlumbingLtd2 ай бұрын
😂😂😂 thanks for your opinion. Works fine for me over the last 10 years
@bravobravoh1344 Жыл бұрын
I like the steel wool, that's better than using sandpaper.
@mikefardellАй бұрын
Thank you
@garyclark3483 Жыл бұрын
Great job.
@culebrasty2 жыл бұрын
Thank you very much !Nick!
@NickTaylorPlumbingLtd2 жыл бұрын
My pleasure! If you haven't already don't forget to like and subscribe :)
@dreadpirateroberts4052 Жыл бұрын
I wouldn’t be too bothered about that “splodge” of solder on the fitting, it’s the 3” run of solder running down from the vertical fitting which is bad to see.
@thedeplorable78672 жыл бұрын
Damn I thought you were supposed to apply enough solder that it runs down all over the place. I have been using way too much solder. Thanks for the video.
@Juantouch123 Жыл бұрын
I'm not sure if this video would work , because it look like he applied not enough solder.
@stepheneurosailor162310 ай бұрын
Brilliant.
@NickTaylorPlumbingLtd9 ай бұрын
I love it! Thank you!
@goochgaming Жыл бұрын
Way too hot!! Heated the fitting first, which is why it was a cold solder joint. Tip was too big and when you saw the flux running, it was really to solder, after you heat the PIPE first!!!
@2011Maynard8 ай бұрын
MAPP gas as we know/knew it doesn’t exist anymore, at least in the states.
@NickTaylorPlumbingLtd8 ай бұрын
Wowza so what do you use? Propane?
@Chop7572 ай бұрын
@@NickTaylorPlumbingLtdyes it’s Propane basically or butane. Depends on what area of the US you are in. Good Video Mate!! 🙏🏽🙌🏼
@foppo100 Жыл бұрын
Just checked my copper pipes out side my boiler.A few big blops and running solder.Crap work by a so called plumber.
@bethtp15 ай бұрын
You forgot to mention cleaning inside of ffitting and always have respirator with map it is a cause of prostate cancer
@tanako982 жыл бұрын
great vid
@NickTaylorPlumbingLtd2 жыл бұрын
Hi Jay, thanks for your kind words and taking the time to write a nice comment. If you haven't already please like and subscribe to my page as it really helps.
@howyg1013 жыл бұрын
Shouldn't you clean the fitting too?
@markpipenko9883 жыл бұрын
Yes you should
@colinfleming22443 жыл бұрын
Things you should be taught by yer journeyman wiping excess flux off b4 soldering first thing told. Saying that we used yorkies wi the solder in not the cheap end feeds. Boss wanted some to be sure no leaks. Used to get end feeds on bg jobs str in scrap bag🤣🤣🤣
@sunflowerbadger Жыл бұрын
This video is really quiet. Not a massive problem for most people, but for people with hearing loss, like moi, too quiet to hear. Looks like a cool vid though.
@Kurt19683 жыл бұрын
You forgot to deburr the pipe
@doctorboy58922 жыл бұрын
He didn't cut it. It was new from Bunnings.
@jeztickles43612 жыл бұрын
Too hot… discolouration on copper Too much flux… running everywhere
@NickTaylorPlumbingLtd2 жыл бұрын
Hi Jez Tickles, Thanks for the comment, Years in the trade and its never let me down and never flooded anyones house either 🤣, there is some truth in your comment, if you over heat the joint the flux will burn out, no flux = no solder being sucked in = flooded house 😂, what I would suggest to anyone learning the trade is when heating the joint, keep touching the solder to the opposite side of the joint to where the flame is heating, do this every 5 seconds or so and when the solder melts and sucks into the joint = perfect temperature for soldering, keep doing this and overtime you'll perfect the technique. If you haven't already don't forget to like and subscribe 👍
@terrythomas79023 күн бұрын
@@NickTaylorPlumbingLtd Yes, but on tap of solder on the top pipe , as in the video, isnt enough. That roll of solder will last you a lifetime
@lxmzhg2 жыл бұрын
forgot to deburr the pipes
@moto55132 жыл бұрын
Volume so low can't hear.
@NickTaylorPlumbingLtd2 жыл бұрын
Hi Moto55, thanks for taking the time to to give me constructive feedback, may I ask what device your listening from? I’m finding on a whole this video is fine but having some issues with volume which I need to resolve. I’ve recently upgraded my camera, sound and even have my own KZbin studio so check out my recent videos and if you haven’t already, don’t forget to like ans subscribe! 🙌
@PanamaSticks3 жыл бұрын
very weak audio
@dontcomply50082 жыл бұрын
Headphones.
@ScottyDog3452 жыл бұрын
I don't loke leeks
@lxmzhg2 жыл бұрын
The 'L' in 'solder' is silent, i.e., 'solder' is pronounced sŏd′ər (sodder).
@daveshegedin25762 жыл бұрын
Hi,I have watched American soldering videos and initially couldn't work out what they were saying..sodder.. In the UK , Australia and here in New Zealand we pronounce it as solder not sodder. There are probably more Commonwealth countries too where it is pronounced the same way it is spelt. Cheers. Dave.
@KendalMike Жыл бұрын
@lxmzhg, You must be an American because that's the only country I know that does NOT pronounce the L! Please don't tell us how to speak out own language. And don't get me started on herbs!
@jeffcochran77212 жыл бұрын
REALLY GOOD TEACHING. MY VOLUME SOUND WAS DIALED ALL THE WAY UP ON HIGH. BUT I COULD BARELY HEAR YOU. PEACE SHALOM ADONIA!
@iceman846 Жыл бұрын
Totally over heated the joint
@daleon962 жыл бұрын
No disrespect, but that's not how you want to solder a pipe...
@NickTaylorPlumbingLtd2 жыл бұрын
Hi Daleon96, thanks for the comment and no disrespect taken, everyone has an opinion, in my defence I’ve been doing it this way everyday for 9 years and never had a problem.
@buddyrevell5114 ай бұрын
No disrespect, but anyone can say/write that, and you were either too lazy or too ignorant to actually tell us the correct way. In other words, your post is worth... phųk all.
@jsoul3282 ай бұрын
Love the example giving with comment😅😅 tfoh
@x-ray-automatic9 күн бұрын
'Two types of people,' situation - some only want to try and help others - our dear friend in this video; others just complain and make no useful contribution to the conversation.
@x-ray-automatic9 күн бұрын
@daleon96 No disrespect, but could you help us out here - a video from you would really help, but stopping short of that could you expand on your comment so we can learn from you too, please?
@DYIIdeas3 ай бұрын
Very good, nice details here that I haven't seen elsewhere. 1.) SPIN pipe fitting to spread the flux around the pipe evenly. 2.) Form the end of the FLUX into a HOOK shape. 3.) If EXCESS FLUX RUNS DOWN a vertical pipe while heating it, I can carefully WIPE the excess FLUX OFF the copper pipe -> BEFORE applying solder. 4.) Copper turns whitish and flame turns green means it’s ready to accept solder.
@DYIIdeas3 ай бұрын
Thanks Great Vid!! Very complete information. Most how to solder videos don't go into the flame adjustment and you fine Sir did!! Thanks