How to solve Ignition Problem In Gas Water Heater, fixing ignition problems of tankless geyser

[@ebrahimcarelse2670]

Thank you brother! This video was highly informative and helped me solve the issue! 👏🏾

[@Rehankhan_HVAC_TIPS]

Thanks

[@prateektambe150]

Hi, My gas geyser ignites when the tap is opened, but switches off automatically in 1-2 mins. There is a continuous sound of ignition until it is on. Water pressure is fine. Please advise what can be the issue.

[@harikrishnan-wr6ci]

Thanks for your video in English bro. I'm from South, difficult to find video in English.

[@Rehankhan_HVAC_TIPS]

Thanks bro

[@jamesbounsall5478]

Very well done mate!!!

[@Rehankhan_HVAC_TIPS]

Thanks

[@ZahoorTariq]

Great work ! I have the same problems in my singer Instant gas geyser .. I'll try to repair then give feed back. Keep sharing stay connected

[@Rehankhan_HVAC_TIPS]

Thank you so much, I am glad you like my video ☺️ Thanks for Appreciating, please keep supporting.

[@Rehankhan_HVAC_TIPS]

Is it repaired or not

[@ZahoorTariq]

I have tried, cleaned well with acid water, but the flow pressure of water has not been adequate. I think there is something stuck in his outlet. How can he get out?

[@Rehankhan_HVAC_TIPS]

Check thier will be iron net in the inlet valve may be chocked.... Does the unit getting ignition. Check the valve adjustment

[@razatahir5688]

Thanks for the video

[@anurodh1306]

How much did the magnetic sensor cost you?

[@azeemkhan-xr4qm]

hi thanks for a helpfull video.my problem is thatmy ignition is working , sparking with tik tik sound but only sound no flame

[@Rehankhan_HVAC_TIPS]

Check the solunate valve, I think gas is not passing through the valve.

[@yaveshdhondee3698]

@@Rehankhan_HVAC_TIPS can you show me where the valve is pleassseeee

[@Rehankhan_HVAC_TIPS]

If your ignition is working need to check solvent value, it's not allowing gas to pass

[@tipeneuriti5489]

that was my fix thanks ,the wire was ok but thfilter was full of stuff and had low water pressure so i removed the 2 screws and cleaned the shaft and valve spring ,1tap open ,bang degree reader turn cold on it clicked and then gas opened heat was instant up 2nd flame 58 degrees but 38 is more desired temp'

[@Rehankhan_HVAC_TIPS]

Great thanks for supporting

[@kermets]

Hello, we get the ignition and the gas ignites for half a second then goes out straight away the box has been inside for 7 years but early morning when it seems colder it will not stay lite... do you have a idea please? Brett

[@Rehankhan_HVAC_TIPS]

Sir need to change solvent valve or check the water pressure

[@varunthakar3308]

Greaat man I found my fault after waching your video..but you can use hindi language also sonthat other people ccan understand

[@rkstudio9869]

OK thanks

[@Rehankhan_HVAC_TIPS]

Thanks you sir

[@ASHISHPATEL-bv8ez]

Can we do electric spark instead of battery cell in gas geyser please let me know

[@saeedptcl]

G bilkul, just purchase the 4.2 to 4.5 VOLT Charger (Plus Socket if possible) from market. Cell wali dabbi kholain just 2 (or some have 1) screw remove kar ke, + - per connect karain and enjoy karain. Check this kzbin.info/www/bejne/rZe1hKamlKaUd8k

[@purushothamp1222]

Where can we get the magnet sensor sir, thanks in advance

[@Rehankhan_HVAC_TIPS]

Sir it depends on region and make.

[@BlueBull998]

Hi. Do you know what current(amps) is needed to start the gas geyser? Approx

[@Rehankhan_HVAC_TIPS]

All geyser has different amps give me specification

[@BlueBull998]

@@Rehankhan_HVAC_TIPS hi. i have 12liter Totai Gas Heater. it used 2 "D" cell batteries. total 3 volt. thanks

[@manupmech2989]

In our geyser after ignition sparking not getting off. Can you please tell me the reason and solution

[@Rehankhan_HVAC_TIPS]

Check the magnet particle inside the water inlet valve,,,, please make it free by using lubricant.

[@manupmech2989]

Sir am getting hot water but spark coming continuously along with flame. Any chance of flame sensor got bad....

[@Rehankhan_HVAC_TIPS]

Sir the main box may be faulty

[@agarwoodnursuryraisinginpa8590]

Sir g mera gas heater b yahi masla ker raha he kia ap muje online guide ker sakte hen

[@Rehankhan_HVAC_TIPS]

Yes aap ka issue Kiya ha

[@kirankumar-ki3ci]

Bro my geyser won't turn off even I stop water flow so I have to close gas connection and if I just put battery ignition starts without turning on tap so what could be the reason.. plz help

[@Rehankhan_HVAC_TIPS]

OK boss Steps to follow. 1] Check water inlet of your geyser, inside this we have one small object. When you put water on at that time it moves upwards and give signals to magnetic sensor to start the ignition and solvent value to open the gas to light the geyser. Check if its stuck, if stuck make it free using little oil. 2] Need to check main pcb if it's reading proper signals or not. 3] Check the solvent value. If again your getting same issues please contact professionals near you. Give me updates.

[@kirankumar-ki3ci]

@@Rehankhan_HVAC_TIPS I will try number 1 - I will let you know tomorrow and thanks for the help

[@kirankumar-ki3ci]

Just tried number 1 and the issue is fixed now thanks - the magnet was stuck inside, thanks again really helpful in lockdown timw

[@Rehankhan_HVAC_TIPS]

Keep supporting my channel, THANKS

[@jagannadharaokandala3488]

Where can i get this magnetic sensor ? Pleaze tell me

[@Rehankhan_HVAC_TIPS]

Check the supplier near your place.

[@tusharpatel9447]

What is the price of magnetic sensor??

[@varunthakar3308]

Tushar Patel 200/-

[@tusharpatel9447]

@@varunthakar3308 ok thanks

[@munafpatel3014]

sr jo ger ki andir ges aata hi vo dairic aata hi lain kaa botal nahi hi to kyaa kar na cahyi .. berner ko kyaa kar nas cahyi

[@Rehankhan_HVAC_TIPS]

Can you write in English please

[@mahadevbiradar2661]

Gas is not flowing burnar

[@fahadtariq.]

@@Rehankhan_HVAC_TIPS magnet is ok But gyser is not working ?

[@fahadtariq.]

@@Rehankhan_HVAC_TIPS help me plzz

[@tipeneuriti5489]

Magnetic sensor does it lift the valve jet ?

[@Rehankhan_HVAC_TIPS]

Magnetic sensor is used to start the ignition only.

[@ZahoorTariq]

I am trying to repair, ignition is happening but burner not getting fire ? Let me know the correct position of magnetic slender, as well as the position of locking spring, placing at inlets pipe?

[@Rehankhan_HVAC_TIPS]

2 inch above the threat, you can check thier magnetic slender is inside the valve... Try to do lubrication to make it free... Each model have different locking spring....

[@ZahoorTariq]

OK, thank you I'll try tomorrow

[@zainasif3510]

sir ignition is not turning off as long as the geyser is running , ignition is continuously there.

[@Rehankhan_HVAC_TIPS]

Ok, check the water inlet valve, inside the value thier is one small iron bar need to make it free . Use small amount of oil to make it free . Than easily you can get solution.

[@anupkhatri6204]

Hi my geyser is not getting started. Geyser switch is not working . Thanks

[@umapathipk4402]

Bro my gas geaser is fire sparks is not coming how to rectified Ignition change Or any changes pls tell me bro

[@Rehankhan_HVAC_TIPS]

1 check the battery , clean the point of sparker & check the connection of Sparker. 2 check the wire if it's cut or damage. 3 ignition box is not working,need to change.

[@Rehankhan_HVAC_TIPS]

Thank you so much, I am glad you like my video ☺️ Thanks for Appreciating, please keep supporting.

[@radham2032]

Hiii gas gresar for falt but not sollution sir

[@Rehankhan_HVAC_TIPS]

Tell me the fault

[@javahharreddivanga1949]

Can you make same video again without background music which is irritating.

[@tipeneuriti5489]

My one did strike all the time the 12 volt switch was turned on but no gas was going to the ignition switch!

[@regrangihuna5089]

Hi, my gas califont runs too hot, when i try to adjust it with the dials, it turns off, its 12v with batteries

[@captainkatsura8628]

Water heater sparks but burner won't turn on. what could be the problem?..Tnx in advanc3

[@Rehankhan_HVAC_TIPS]

Check the solvent valve ,which is defective. Not allowing gas to pass

[@captainkatsura8628]

@@Rehankhan_HVAC_TIPS wht is solvent valve? sir the product is new. it lit before somehow when the technician shaked the outlet tube but stopped burning after some hours.

[@Rehankhan_HVAC_TIPS]

Check from where the gas is passing in the inlet tube , above that one part is installed is call solvent valve. Check this part if the gas is passing from that or not.

[@ZahoorTariq]

I tried, and another arose, now gas is not getting on ... please make a video to resolve this issue

[@Rehankhan_HVAC_TIPS]

Brother sorry to say ,I don't have that product now. It will be difficult for me to make video.

[@deepakdotia4549]

Thanks sir , for making such informative video. I m i Mumbai and using an racold gas geyser on mahanagar gas pipeline (cng) connection, my problem is that when I insert new batteries in gas geyser it starts and works properly and perfectly, but approx 20 days after it doesn't start unless and until I ignite my stove (kitchen burner). This process continuous, for another 25 days and then it stops working completely, then again I insert new batteries and the whole process repeats, Kindly reply

[@Rehankhan_HVAC_TIPS]

Total how many days it's working continuously....

[@Rehankhan_HVAC_TIPS]

Gas inlet valve should be cleaned time to time...

[@Rehankhan_HVAC_TIPS]

Does the ignition light continuosly? ( Spark)

[@philipfeghaly4210]

Bro my geyser won't turn on by itself , the lcd is always on and showing that the water is open , i get hot water only if i switch it OFF then ON, flame will stay lit until i turn off the water & if i turn on the water again the flame wont turn on automatically , i need to turn the switch OFF then On again . Please help

[@Rehankhan_HVAC_TIPS]

1st check if the gas supply is ok or not. 2nd check the switch 3rd check the water inlet valve, inside that thier is a magnet if the magnet is getting stuck apply some oil & make it free . Let me know later if it's ok or not

[@philipfeghaly4210]

@@Rehankhan_HVAC_TIPS 1: gas supply is ok, when i turn off then on the flame works well untill i turn off the water, 2: ON OFF switch is OK since the geyser work fine manually, 3: my magnetic sensor is always On, i removed the plug and the lcd turned off, i reconnected the plug (without opening the water or gas ) and the LCD turned on with ignition & showing me that i have running water. any video showing how to check the water inlet valve or its magnetic sensor faulty ? ? (sensor always on, 6 months ago it was working fine )

[@philipfeghaly4210]

OK i understand now i think the magnet is getting stuck like u said, can i tap it from the outside without unhooking everything & OILING ? will it get loose ? because i have bad Direct installation

[@Rehankhan_HVAC_TIPS]

Sir you can remove only the water inlet Valve connection host & apply some lubricant,no need of removing hole system. If you tap the value can get break ...

[@philipfeghaly4210]

@@Rehankhan_HVAC_TIPS its fixed thank you good sir, i had to unhook everything and shaking it and tapping the the inlet valve for the magnet to drop, it was stuck very hard .

[@alzaghir]

thanks

[@Rehankhan_HVAC_TIPS]

No problem

[@nishanthnl18]

Hello, my gas geyser magnet is working properly , i am getting the spark but gas is not igniting. please help

[@Rehankhan_HVAC_TIPS]

Hlw sir please check the solonet valve, its not allowing gas to pass . Or the main pcb box is faulty.

[@radham2032]

Help me

[@Rehankhan_HVAC_TIPS]

Tell me the fault first

[@radham2032]

@@Rehankhan_HVAC_TIPSGeyser sparking Sound is coming but it is not sufficient to get Hot water.

[@Rehankhan_HVAC_TIPS]

Check the flame of heater

[@Rehankhan_HVAC_TIPS]

If the flame is low than adjust the gas inlet nob

[@radham2032]

Same problem sir

[@suvamswain1285]

What was not happening

[@Rehankhan_HVAC_TIPS]

Sorry

[@umapathipk4402]

In Ignition is working but fire is not coming

[@suvamswain1285]

No ignition at all. No spark sound. Tick tick sound is not there...

[@Rehankhan_HVAC_TIPS]

Ok

[@Rehankhan_HVAC_TIPS]

Check the battery Check the ignition board And let me know

[@VANGOOD-Water-Heater]

Thanks for your video

[@Hukum1]

Thnk you