For those of you that want to flush your engine but don't want to remove the oil pan try this. This method cost a little more, due to the type of chemical used, but works very Fast
Пікірлер: 443
@jerrymiles15585 жыл бұрын
I'm an old retired mechanic and I have seen people do stupid s@#% to an engine, but this is about as bad as I have seen.
@crazysexycool1804 жыл бұрын
like you said you are retired, for a reason so stay retired, or open your mind and learn some new tricks
@dee73314 жыл бұрын
More like “How to directly Murder the life of your innocent Car Engine in a fastest way😂
@funnydubby64014 жыл бұрын
Artistry Photography no ur just an idiot lol
@paulmannering38313 жыл бұрын
He is totally mental !!! Grining metal and grit into his engine!!)!))!)!)
@paulmannering38313 жыл бұрын
Omg never seen anything so bad. Blow out debris? Just blowing debris all over inside engine!!!
@gassanchaptini6184 жыл бұрын
So engine didn’t survive for part ( 2)😂😂😂
@joaopnascimento5 жыл бұрын
Reving the engine that has a oil pressure warning? And in top of that he says that the engine is starving for oil... That engine is gone from the beginning. I ask myself where did those debris go to... And the brush in the cam lobs... scaring... I wonder why there is no part 2 :-)
@fuzzymcuppets61675 жыл бұрын
Why the hell do customers wait until their instrument clusters lit up like a Christmas tree to have someone look at their car? I would guess oil pick up screen is clogged with sludge from lack of maintenance.
@JOHNPRESTON7824 жыл бұрын
All those ak-47s and 50 cal guns in Iraq are all coming back to me when he started the engine.
@baronvolkov61724 жыл бұрын
Damn that hurt to watch even on a kia! Metal brush straight to cam lobes LMAO that head is DONE! Gamee overr
@tylert65735 жыл бұрын
15:54 peice of gasket just flying off his thumb into the spark plug hole there
@willysoulbrotha4 жыл бұрын
WENT BACK TO 15:54 JUST TO LAUGH MY ASS OFF
@danh94424 жыл бұрын
Runs like a dream now - no doubt
@deecee56934 жыл бұрын
You got em coach! Great attention to detail.
@plastbestikk3 жыл бұрын
While he was saying "you do not want this in your engine!" But either way, this engine wont last another plug change by far.
@joaodoege31112 жыл бұрын
I see a lot of people criticising here but no one has better channel, making videos to teach people. easy said than done, if you can do better make a better video then
@wilsoncrocker5 жыл бұрын
a wire brush. on an air gun. directly onto the cams. i really, really hope this is just a trolling vid. 😮😬
@crazysexycool1804 жыл бұрын
wire brush is softer then the metal its cleaning, how do you think you would clean stuff like this?
@funnydubby64014 жыл бұрын
Artistry Photography no it’s not steel on steel is not good lmao, use scotch bright pads
@wilsoncrocker4 жыл бұрын
@@crazysexycool180 just because a metal alloy is softer than another doesnt mean that it cant damage it. when youre talking about tolerances of 1/10,000 of an inch as you do with cams & cranks, using a wire brush is one of the last things you want to contact lobe surfaces. might as well sandblast the crank while your at it. how would you properly clean a cam? hint: not with a wire brush spinning at a couple thousand rpm. with all the tiny metal shavings youve created just close it back up & run the engine. all that loose metal will clean everything nice & bright in no time...
@alanlo-5573 жыл бұрын
Look at the context. Cheap car. Well-used. Likely that the customer doesn't have a lot of money, right? So our guy is trying some unconventional methods (doesn't make them wrong) to save the customer from having to buy a new head+ many hours labor The results speak for themselves. This isn't a formula 1 car. If a cam lobe had a few microns wear from the brush (and that's even doubtful), but the car ran much improved than from when the customer brought it in, what difference does it make in the REAL world?
@wilsoncrocker3 жыл бұрын
@@alanlo-557 tell you what, dont take my word on it, go to your nearest machine shop & show them this vid and see what they say, or tell them youre going to clean your cam lobes with a high speed wire brush because you think thats fine. youll get laughed out of the shop. "jus because its unconventional dosnt mean its wrong" well pal, cleaning the cam lobes of your cars engine is not only unconventional & wrong, its fcuking stupid. if you cant afford to do a job right, you sure as hell cant afford to do it wrong. eta: im ASE cert in engines, im not just some yahoo trolling on youtube
@jeffreysheldrake79434 жыл бұрын
Use an oil suitable for your engine. Some oils do sludge but if you have a low oil pressure drop the sump and check the oil pump.Modern oils will keep your engine clean if changed hot and regular
@sungn45125 жыл бұрын
hard cooked on sludge is an indicator of oil burning / infrequent oil changesyour before & after cleaning valve cover provided a NICE clean polishthanks for showing 2 different ways you clean: chemicals & abrasion
@Mk5_Life6 жыл бұрын
PEOPLE JUST CHANGE YOUR DAMN OIL TAKE CARE OF YOUR CAR AND IT WILL LAST
@Unknown-jl7mg5 жыл бұрын
looks like mega LL intervals to me... which is the root cause
@tardeliesmagic5 жыл бұрын
Just would'e used a good engine flush,change oil,remove top cover n just clean it,drop oil pan,clean oil pan,run it for 20 mins and change the oil again!
@igotajopamerica30404 жыл бұрын
Its a Kia. Change your oil everyday and it's still junk.
@davidgomes79464 жыл бұрын
Yeah sure...try this extended oil change with a koenigsegg and see if stays alive. Maintain a car with militairy precision and any car will get to a million miles.
@chrisao19872 жыл бұрын
Piece falls down in the spark plug hole lol 16:00
@MFahad-uy7ci4 жыл бұрын
Its suppose to be washed by diesel and the tool you can use is hand brush which does not have chances to break a part its threads inside the engine,(eg tooth brush) unlike wire scrubber with machine, it breaks alot of its particals here and there. drop down pan should be washed as well. also throttle should be washed same way.. done that in many cars and it worked always, but you need to use flushing oil twice aswell.. later put new engine oil and oil filter..
@skynetsworld4 жыл бұрын
there is an old saying: "you can't put enough brake cleaner into an engine" or was it "you should't put brake cleaner into an engine"? ... i'm confused
@JayzBeerz5 жыл бұрын
This is a prime example of not changing your oil at proper intervals.
@ttank946 жыл бұрын
There probably isn't a part 2 because the engine spun a bearing and died and wouldn't look good on his channel. Any time the oil light is on you need to drop the pan and clean out the pickup if you expect the engine to live. You're a hack if you expect to just pour shit in the engine and expect it to clean itself when it gets that bad.
@calvinjames56824 жыл бұрын
Lmao Cracked me the f**k up this comment
@joaodoege31112 жыл бұрын
And nobody is watching your content because there's none. If you think you know better then stop being lazy and post better videos
@crazysexycool1808 ай бұрын
2023 car still running. Thank you please like, share, and subscribe, also please check out my other channel Salem Taxi, on KZbin for more material on a different level.
@trevormangus78326 жыл бұрын
If you want cheap dump a gallon of diesel in the oil at least its oil based and won’t damage the cam timing gears and seals brake cleaner BAD Don’t use inside an engine unless its dissembled which is what this one needs. A tear down and rebuild
@paulbricklayer44914 жыл бұрын
Trevor Mangus or atf
@scotthart62372 жыл бұрын
Or just drain and run kerosene at idol.
@elgroso8066 жыл бұрын
how "not" to flush your engine !
@erinarnold66975 жыл бұрын
The blue lid oven cleaner works the best on that caked oil try it, it's way cheaper. I wash the outside of my engines with it. And I use it on the inside of the engine when I'm rebuilding them to make everything look like new again
@mr.mrs.keesee1169 Жыл бұрын
I concur it’s the best but yellow can is marvelous!!!!
@MrBennyGonzalez5 жыл бұрын
That bird at 4:51 made me pause the video and looked at the tree i was underneath of. LOL
@kevina46744 жыл бұрын
My mk4 turbo makes the same sound when you pull dipstick and try to pull oil cap. Cause I have the pcv valve touted through the catch can with a few one way check valves. So it acts like a Venturi sucking out any air and blow by.
@glenndavis27625 жыл бұрын
why even do this??? the three cans of brake clean cost more than the motor is worth.
@AikidoTubeSock5 жыл бұрын
A piece of the old brittle valve cover gasket drops into the spark plug well at around 16:00
@DesertSnow12 жыл бұрын
You’ll also see it in there around 19:08 lol
@harisyoung4110 Жыл бұрын
And it will be drop into the combustion chamber during the next spark plug change.
@deanjet5 жыл бұрын
You power flush yesterday's burrito, not your engine!
@dean54853 жыл бұрын
if ya poured a little oil on the crank and chain you would avoid all that clacking and metal on metal chance of more damage
@scotthart62372 жыл бұрын
IS that steal wool or a metal scouring pad??? Wouldn’t that leave huge swirl marks in the cover and then lead to worse build up in those crevices?
@toonmag505 жыл бұрын
In the UK I've used lots of dodgy garages and so-called mechanics, bandit garages are around everywhere. I have learned through experience to use certified garages recommended by the RAC and AA, which are national breakdown organisations. Always quality work, and my cars became hand-me-downs for my adult children. I recommend to everyone to trust your major breakdown companies . I wonder if this bloke is accredited?
@donfrancis13755 жыл бұрын
this is the whole reason i learnt to do my own cars. everybody is a cowboy especially around Birmingham lol. That and being Lexus it gets kinda pricey...saved myself 500 quid doing cambelt and waterpump myself...the cowboys quoted more than the dealer lol.
@gary1962miller2 жыл бұрын
Only on air tools
@crazysexycool1808 ай бұрын
update years later this car runs great, have a nice day Thank you please like, share, and subscribe, also please check out my other channel Salem Taxi, on KZbin for more material on a different level.
@jamesbowen31685 жыл бұрын
people do not use a wire brush on an air tool, because at high rmp's the wire can come off the brush and into the engine. you get just one of those wire's between the bearing and the crankshaft you're in big trouble, that wire will eat into the bearing and the crank.lay down paper towel's to stop anything from going down into the engine. then take your time and clean it, use a toothbrush or a wire brush by hand, and watch than no wire is getting into the engine.alway clean both side's of the valve cover, when it's off the engine is better.when working no a engine fast cleaning is not always better, take your time do it right.
@pfoxhound4 жыл бұрын
Are you a relative of Scotty Kilmer?
@exilemike3 жыл бұрын
Scotty Kilmer is much more intelligent
@frankie22346 жыл бұрын
Hate to bother you, but where is pt 2 of this video. I was looking forward to seeing the other valve cover taken off and the results. Thanks for the video.
@michaelrohandodds18506 жыл бұрын
So have you not remove every oil film leaving no lubrication with brake cleaner? Would that not cause scoring on start up ??????? I want to know
@Lilmiket1000 Жыл бұрын
Probably will. But this is a well abused car that already has some scoring. Not a brand new engine. This engine is so abused it will probably die soon regardless of what he does to it. Anything he can do here is an improvement to what it was before lol. I do believe hes taken all that into account. I'm pretty sure he wouldn't do any of this to a new engine.
@stevenmckinlay44784 жыл бұрын
Good job, As for the know it all about the wire brush on cam lobes...... Get a grip. No way will the wire brush damage the lobes. Maybe if the wire brush was on surface for ten minutes even then minimal damage. This guy knows his stuff, gets the job DONE RIGHT. Top end clean, bottom end clean. Change oil filter, new oil, engine flush, dump oil, change oil filter, new oil, engine flush, dump oil, change oil filter, new oil. Internally engine pristine. Very good Job.
@williamdevitt78667 ай бұрын
steel wire brush will damage the gasket surface of the aluminum head and cover as for this guy knowing his stuff he know jack shit dry started that engine with no lube on cam bearing yea he knows his stuff my ass
@potatohamlin52422 жыл бұрын
Can you use a plastic brush,scotch bright, and a vacuum
@axenz16 жыл бұрын
I've try this before cleaning using screwdriver then blow it using air compressor... then refill new oil and filter... start the engine more worse...the valve ticking very loud... until I remove the out the oil pan, found out all the gunk debris clog the oil pump filter and more on oil pan... So I remove the oil pump filter a clean with kerosene and blow with air pressure.. install everything and engine back to normal
@Sarin-Dan5 жыл бұрын
Haha starved of oil... When i rev the valves make more noise... Haha no mate that's your bottom end nocking!!!!
@raephellbenham87816 жыл бұрын
What about the other side of this v6?
@HowardJrFord5 жыл бұрын
When an engine has no oil pressure you're not supposed to run it until the problem is resolved. It's especially stupid to rev it or drive it with no oil pressure. This engine was already toasted before you flushed it.
@crazysexycool1808 ай бұрын
2023 engine still running great Thank you, please like, share, and subscribe, also check out my other channel Salem Taxi on KZbin
@daisybeagle62594 жыл бұрын
What about ungluing the piston rings?
@johnbailey96514 жыл бұрын
Oh My Goodness. I cannot believe what I have just seen and I had to watch it all the way through to make sure. Whatever you do fellow KZbinrs - do not follow one single word of the "advice" given in this video. Read all the comments below - I heartily concur with them. One telling point, the guy changed the cover gaskets which were old, true, but would have continued to work just fine provided they weren't messed about with - and ignored the broken cam chain guide?? In all honesty, which do you think is more important? Also, when started up after the rebuild I nearly leapt off my seat with the racket the engine was making!! And when the oil was dropped? I'm no chemist but it looked like 50% oil, 50% crank bearing material coming out!! I feel sorry for the current and any future owners of this poor Kia.
@Trenscendent2 жыл бұрын
Did you not hear him address the broken timing chain guide around 30:35-31:00?
@crazysexycool1808 ай бұрын
update this car still runs great. have a good day 2023
@crazysexycool1808 ай бұрын
Thank you please like, share, and subscribe, also please check out my other channel Salem Taxi, on KZbin for more material on a different level.
@quintonmuna4 жыл бұрын
I bet if you drop the oil pan and look at the oil pick up tube it will definitely be clogged.
@tonyradca12355 жыл бұрын
Rev it a little harder. I want to see that rod rocket itself out the side of the engine. Your garage should have a parts cleaner or a dip tank.
@armyblouvet546 жыл бұрын
Omg. Good bye cam lobes and bearings! Do not do this people
@InetaGphotography6 жыл бұрын
i used simple dish soup and metal conton to clean main part and modeling tool to do smakest corners and got it spotles
@nsrracing16 жыл бұрын
Mongo the Mechanic that car was gone from the beginning. Anything he did to it was an improvement. It's a Kia and a taxi at that. Not a ferrari.
@theconquera105 жыл бұрын
U forgot about the crankshaft
@IBISMK14 жыл бұрын
So I have been a slob about changing my oil. 350 5.7v. Should I just change the oil a few times back to back after running for a few mins between changes? Wondering if the detergents will help if they are fresh..
@derekanderson686 жыл бұрын
How much do you charge to do something like this?
@tchrisou8125 жыл бұрын
This might be a crazy idea but what if you were to totally fill up the engine with the "awesome" or MMO and let it sit for a couple of days? drain and refill with the proper oil level ? thoughts?
@Lilmiket1000 Жыл бұрын
I did that with my 200k prius. Except I used Berrymans chem dip. I let it idle for 15mins. let it sit a week. Then came back and idled it again for 15mins. Then I did the oil and filter change. Cleaned it out very well. but not completely. Ive gone another 20k miles and no issues yet. Runs better actually.
@tchrisou812 Жыл бұрын
@@Lilmiket1000 That Berrymans is good stuff. The Prius is a great car. Thanks for taking the time to tell about your knowledge, I appreciate it
@secalcavazos32044 жыл бұрын
He really should have poured some assembly Lube over those cams and everything before you put that valve cover on so you wouldn't have such a horrible dry start
@TheSiegeGaming5 жыл бұрын
We just watched a murder
@fastlaneautos23184 жыл бұрын
WaveyBoy hahaha...I want my 3 min back
@bbarnett76673 жыл бұрын
They were driving it that way so he isn’t hurting it trying to remove the gunk and varnish that’s already clogging the journals
@chrisrogan39555 жыл бұрын
How often can you flush a engine with LA
@GeorgeAusters3 жыл бұрын
I would have gave it 1-2 oil changes and flushes prior to taking off the valve cover
@Hazeyone79773 жыл бұрын
That was a DRY start! That hurt! Folks this is a video of WHAT NOT TO DO! Those cam bearings had to get damaged. If the chain had that much slack that it was slapping the cover, its time for a new chain. Im sure now thus engine is DEAD. Also invest in a tripod! Most of the video is you trying to talk over your air tool.
@ejaydc81982 жыл бұрын
I am battling in my camry because of oil pressure indicator keeps coming on and off..i thought its only the sending unit sensor is broken..but the only solution is drain the oil, clean the clogged oil pick up tube and the oil pan..saves my engine a lot..
@Jazzy9165156 жыл бұрын
1) Brake cleaner has chloride in it. If you use it to clean your mating surfaces before assembly then the chloride will eat up the gasket. 2) proper torque on rubber valve cover gaskets will cause then to wear prematurely and leak--use a torque wrench.
@crazysexycool1806 жыл бұрын
well said, but you forgot, they make non chloride brake cleaner. also your correct about the torque wrench, but there again the new-style of gaskets that are sold aftermarket for the valve covers are non torque gaskets.There type gaskets have metal shims to avoid over torqing on the gasket.
@williamcampbell65896 жыл бұрын
It said non chloride on the can.
@robertmaybeth34342 жыл бұрын
Brake cleaner's fine for cleaning gasket surfaces. What you don't wipe off from the cleaning, it just tends to evaporate. I used it a thousand times and never had a problem. By the time you go to put on the gasket all the brake cleaner's long gone.
@1995dresser2 жыл бұрын
29:58 the engine sending out Morse code. Decoded it says I am dying
@crazysexycool1808 ай бұрын
car still runs years later Thank you please like, share, and subscribe, also please check out my other channel Salem Taxi, on KZbin for more material on a different level.
@MrPanetela4 жыл бұрын
la totally awesome contains 2-butoxy ethanol i get it, its a solvent, and a good one for oil and sludge. the only thing i would do differently is to not run the engine, but to use a pump instead; to push it thru the system. Sort of a dialysis machine for cars in which the adapter would screws into the automobile oil filter hole.
@tonychambers92284 жыл бұрын
i guess you didnt look up the other ingredients being 88-95% water. Yeah lets put water in your crankcase. Shit is retarded
@crazysexycool1808 ай бұрын
cost of machine? Thank you please like, share, and subscribe, also please check out my other channel Salem Taxi, on KZbin for more material on a different level.
@SUPERNVA-gr4sr2 жыл бұрын
That noice when he started
@rononeal9794 жыл бұрын
Car do u have any last words? 😆
@jadywong42495 жыл бұрын
so much cringe in this video
@ericsontuliao13976 жыл бұрын
Wtf..........
@mcmadlyns5 жыл бұрын
Can you use rocket fuel i was told it well clean your car engine like brand new and increase horsepower
@TheBadpav5 жыл бұрын
Jet A fuel is just Kerosene. just go to walmart and buy a couple of gallons.
@ianwilds31395 жыл бұрын
Instead of brake cleaner buy a quart of KREEN and put in a spray bottle and wet top end down then lay valve covers back on to reduce evaporation. Repeat a couple times let soak overnight if able, next day reinstall valve covers start engine let idle for 15 minutes then change oil. I had amazing results doing this.
@1Corinthians15.1-45 жыл бұрын
Do you have a video on that? I have sludge in my engine and I'm looking at different options.
@crazysexycool1808 ай бұрын
so this process you mentioned sound time consuming,
@chriscoralAloha4 жыл бұрын
This was hilarious. Thanks for making me laugh so hard.
@JINGLESFASHION3 жыл бұрын
could i use some chemical and a pressure washer to do that job ???????
@gabrielel-kharraz92216 жыл бұрын
What is the reason that makes the engine creates suction
@Sci-Mon14 жыл бұрын
Vacuum leak
@gabrielel-kharraz92214 жыл бұрын
@@Sci-Mon1 tnk u
@Sci-Mon14 жыл бұрын
Gabriel El-kharraz but this leak is pretty bad is it’s that noticeable.
@rrmorris673 жыл бұрын
I wonder if he cares for pets like he cares for cars? That dog has no shot
@donzizx2075 жыл бұрын
What about the rear bank, you clean that part or you only do half a job. And far as blowing brake clean and blowing oil sludge into the block is really not smart
@AzizAkbiyik3 жыл бұрын
Easily cleaned with cellulosic thinner and hard brush. Brake pad cleaners will ruin the valve tires.
@crazysexycool1803 жыл бұрын
no it will not.
@Sci-Mon14 жыл бұрын
This was hard to watch. Can’t believe you ran the car with all that break cleaner in it.
@TuningCustomUpgradeCarParts6 жыл бұрын
really a great job boss
@kelsycunningham84522 жыл бұрын
Mind you, on Hyundai you can change oil every 1,000 k. Engine still will fail 120,000 k or 75,000 miles
@mcericx2 жыл бұрын
thats some kind of wear protection if the cams arent even able to scrape away the old crud
@cme31722 жыл бұрын
A portion of the video you skip over what did you use to get the gunk out?? Off the cams
@chrisoliveira69413 жыл бұрын
Wow, just wow. This has to be a joke, right? 😳
@eskon123455 жыл бұрын
My 03 Open Vectra had some small knocking noise(lifters maybe), i just added little bit of ATF to the oil, drove the car for like 1tkm (or 620 miles) and changed the oil/filter. Oil was quite black and there was small chuncks. The noise was mostly gone and gonna do the same again soon, gonna remove the oil pan aswell next time (maybe should have done it during the 1st time but whatever)
@DKSE1238 ай бұрын
What's an open vectra ?
@ledwysdelgado73042 жыл бұрын
But what about the oil passages?
@barenekid9695 Жыл бұрын
That Noise (with No Oil pressure) is not the valves rattling ... Rather it's the Rod bearings pounding out. You are destroying what's left of that engine
@crazysexycool1808 ай бұрын
engine still runs years later, looks like i added life.
@sammyhiers45092 жыл бұрын
the odometer read 12,00- miles, why not go to dealer for warranty work
@johnh85464 жыл бұрын
This comment section has partly restored my faith in KZbin comment sections. Do not!!!! Use a wire brush in your engine. That’s a great way to leave a bunch of small metal bits of death in your engine.
@precisiont5188 Жыл бұрын
I wouldn't let this guy even touch my vehicles.
@crazysexycool1808 ай бұрын
this one is still running, years later how yours running?
@FastEddy53 жыл бұрын
Holy shit! Did this still run after
@crazysexycool1803 жыл бұрын
runs great
@vernonbosshard9317 Жыл бұрын
I'm working on the exact same engine, you are pissing in the wind. there is SO much area inside this motor. I got this van for cheap, it was overheated, all 3 rear cyls were breached. Sludge, the whole nine yards, the cyls sat for 3 yrs with plain water in them.
@tombruce6398 Жыл бұрын
I agree with the old mechnic
@jamieb95565 жыл бұрын
How you suppose to drive it with a broke guide
@heavymechanic26 жыл бұрын
Its no surprise to see a Taxi Cab wanting a cheap fix to years of neglect. These companies wring every penny out of their equipment and cry at the repair cost... Whats your opinion of the ATF flush I see online?
@stevebellen86746 жыл бұрын
heavymechanic2 tranny fluid work I add a quart to my oil like 3 days before I change it 30 year mechanic
@z31rider245 жыл бұрын
You can also run ATF on idle. Next oil change, drain oil, change oil filter and fill up with ATF. Run on idle and idle only for 15 minutes. Drain add oil and new oil filter. Next oil change should be @ 1000 miles since you will have had ATF residue inside engine. You can also add half quart of ATF on new oil. Run it for no more than couple hundred miles. To keep things Cost effective. Buy Oil, ATF and oil filter @ Walmart/ Supertech brand. You get quality @ a very low price. Note: ATF has detergents and does an excellent job @ cleaning.
@ricks.85226 жыл бұрын
I use Auto-RX for sludge removal ... I have treated many engines and transmissions with it ... honestly it has worked great each time. It is really good for transmissions as well .....
@Memphian10005 жыл бұрын
Lol! The auto rx scam.
@dennisking1555 Жыл бұрын
This is crazy,brakes all the basic rule of servicing and engine with oil pressure problems
@infinitybandofkent4 жыл бұрын
why are you wire wheeling aluminum
@jopisano675 жыл бұрын
This guy barely changed his oil. That valve cover looks like he missed one too many oil changes lol.
@Specialized19936 жыл бұрын
Ohhh snap, my eye twitched when he used a grinder brush on that cam. lol wanna be mechanics these days crack me up.
@crazysexycool1806 жыл бұрын
the brush bristles are softer than the harden metal of the cam, lol Wanna Be Critics that don't know Shit, and too dumb to open their minds to learn new things, cracks me up.
@williamcampbell65896 жыл бұрын
@@crazysexycool180 then where is part 2 of this video?
@jopisano675 жыл бұрын
@@williamcampbell6589 Part 2 is at the junkyard.
@dominiquestephenson1954 жыл бұрын
Joey O - LOL!!!
@JohnDoe-gz8dw4 жыл бұрын
It's not at the junkyard, been long enough that engine has been melted down/recycled into something else 🤪
@youandiryan4 жыл бұрын
Oh my GOD!!!!!!! Did you really start the motor with brake cleaner in the crankcase and oil pan 🤦🤦🤦🤦🤦🤦. This destroys the motor, and brake cleaner renders the oil that's already in the engine useless because it's a solvent. so you're basically using the brake cleaner to lubricate the motor. You're right that flushes the engine alright .. flushes the engine of any life it had remaining. Also there are seals deep inside the engine. Brake cleaner destroys those seals. you should never ever ever ever ever ever ever ever ever ever ever flush an engine with brake clean. Hahahaha. Is this is a troll?
@crazysexycool1808 ай бұрын
update 2023 car is still running great, Sooooooooooooooooooo, what was you saying? Thank you please like, share, and subscribe, also please check out my other channel Salem Taxi, on KZbin for more material on a different level.
@Ezamm87 Жыл бұрын
thanks man you save me a thousand bucks!
@crazysexycool1808 ай бұрын
Thanks for watching , please like, share, and subscribe
@boanerges57234 жыл бұрын
How to get a return customer: step 1 ruin the engine, step 2 wait for them to return with broken vehicle.
@crazysexycool1804 жыл бұрын
step 1, change the oil , take care of the car. it came broke, left fixed, now whats your issue?
@boanerges57234 жыл бұрын
@@crazysexycool180 the damage caused by your "repair" will at least get you a possible return customer. It didn't leave fixed, it left with a different issue. You put brake cleaner into it and used a wire brush on the cam lobes among other things. It was a terribly neglected engine so whether it was worse than the damage already done is debatable, however, I wouldn't want this procedure being performed on my engine, especially an aluminum block.
@atomikvenum4 жыл бұрын
@@crazysexycool180 you literally dropped a piece of metal into the spark plug hole lmao
@sherryturner76953 жыл бұрын
Everyone has their own path it looks like. Please stay on your side of town!
@IcebergZim6 жыл бұрын
hi i have a toyota vvti 1nfze petrol engine. bought it and took it for a full service had a slight knocking sound before and was misdiagnosed for a timing chain that needed replacing. They didnt flush the engine it now it has the oil light on now sound is louder even sounds like a diesel engine a loud knock.Engine still starts. What should i do? Flush it or not or it could be a rod bearing thats worn out??
@apartmentswales5 жыл бұрын
you were screwed, sounds like they did not diagnose the correct fault, or did they? When you had the car back was it sounding smooth, if so then they were probably correct and the fault you now have is a different fault. It happens, sometimes shit follows shit and it is time to dump the car and move on.
@IcebergZim5 жыл бұрын
keithspence thinking of buying a new engine it's way cheaper
@apartmentswales5 жыл бұрын
Well from what you have described it does not sound good and a New Engine could be an option, but you failed to mention what did it sound like after the Timing Chain was changed, by the way I am a retired Engineer and in my 45yrs I have never heard of a Chain being a problem, a Chain Adjuster, yes! that can cause the Chain to RATTLE, but this noise sounds nothing like an Injector not working properly or a Camshaft, or a Conrad Bearing or Main Bearing on the Crank, so what did it sound like when you had it changed??? Changing the oil, or flushing, will NEVER in a MILLION YEARS get rid of an Engine Knock. I did have a knock once that sounded like the Main Bearings on the Crankshaft, but with a stethoscope it turned out to be coming from the lower Front Crankshaft Pulley and was indeed the V Belt Pulley that drives the Generator [alternator] etc Keith Spence Eng
@fix-and-drive-diy-repairs5 жыл бұрын
I would remove the cylinder head and oil pan and thoroughly clean them.
@finarollerz4 жыл бұрын
Valve cover, regular gas and a plastic brush works best, lil cost.
@crazysexycool1803 жыл бұрын
Great point!
@543helge4 жыл бұрын
When this has take place...it's too late with this metod. You have to take the engine apart and clean it part for part!
@Eduman19795 жыл бұрын
my 15 years old car does not have any sludge or gunk on valve cover i change the valve gasket thats why i saw the cover even the camshaft was so clean changing the oil every 6 months or 6000 km which ever come first I used semi synthetic oil remember prevention is better than cure
@crazysexycool1808 ай бұрын
Thank you, please like, share, and subscribe, also check out my other channel Salem Taxi on KZbin
@danjan63854 жыл бұрын
Hi from Australia. That is the best diagnosis/ flush i have seen. I have chased that very same sound for years, flush gone, return, flush gone. but your rockercovers off and vac and parts cleeaner,,, that is the answer,
@sugargraham79204 жыл бұрын
Probably should have left the machanic work to tha doggy 🤦
@buckaroobonsi5552 жыл бұрын
Brake cleaner is generally expensive Naphtha in an aerosol can. You could buy a large amount of Naptha for far less. Maybe purchase a can of actual engine flush from someone like BG since you can easily make your money back from the customer and have a produce designed for the job. Plus you save the little tokens that come in the can and the distributor will give you perks in exchange for the tokens!
@danielkaledo7718 Жыл бұрын
You are a perfect example of why you should EVALUATE most of what you read on KZbin !!!!!
@crazysexycool1808 ай бұрын
Thank you please like, share, and subscribe, also please check out my other channel Salem Taxi, on KZbin for more material on a different level.
@Sci-Mon14 жыл бұрын
Sometimes the best thing you can do is switch to synthetic, drive it 1000 miles and change it then. Slowly up the frequency until it’s clean.