How to Super Flush Your Power Steering System

  Рет қаралды 622,081

FordTechMakuloco

FordTechMakuloco

Күн бұрын

Here is a cheap alternative to the vacuum bleeder adapter shown in the video-
www.amazon.com/...
Mercon V used in this video can be bought here-
www.amazon.com/...
In this video I go over how quick, simple and affordable it is to do this essential maintenance. The best fluid to use in the system and flush with is Mercon V.
New R/C Channel R/C Addict Makuloco-
/ @rcaddictmakuloco
Facebook-
Ford Tech Makuloco-
/ 651813524932940
R/C Addict Makuloco-
www.facebook.co...

Пікірлер: 495
@trevor5929
@trevor5929 3 жыл бұрын
Im a retired Ford mechanic. My system is similar but saves headache of bleeding. Start by raising the front end on jackstands to get the weight of the car off the wheels. Hook up the flush system the same way but instead of just cranking engine over and letting it run out of fluid, i have a helper turn the steering lock to lock while i monitor the resivour and add fluid before it runs dry. This way no air gets in and the flush is done after i run 5 quarts through. Its a much faster cleaner way of doing a good job. And as a mechanic, time is money! Also, stick to the 15second crank rule to save the starter. Dont just crank it till clean fluid runs out. Good luck!
@davidck66
@davidck66 4 жыл бұрын
THANK YOU!!!!! I almost took our van to the mechanic as I thought that the power steering pump was bad. After seeing your video, my son and I followed the steps in this video. Today, the power steering is as quiet as a mouse. THANK YOU!!!
@gottocamp
@gottocamp 5 жыл бұрын
Brian, as always great vids and advice. I followed your technique on my ’10 Explorer with a couple of mods: (1) first started out by draining and removing the reservoir to clean it out. Finished the clean out by adding some new fluid and thoroughly rising out any final contaminates / cleaning fluid. And (2) followed the suggestion by Mice C to turn the steering wheel (my car was up on jacks) while cranking the engine. Overall used abt ½ gal of Mercon to completely flush. And no foaming or air whatsoever. Next up my 07 Expy.Thanks!
@unclematt3
@unclematt3 Жыл бұрын
If you can't put it up on jacks, you can put a bunch of shiny magazine pages under the front wheels and that makes it a lot easier to turn lock to lock. I too follow your method, and it was stunning the black gunk that came out as I was turning. I have a buddy just filling up the reservoir as I go. I also ran the output line down through the bottom of the engine bay so the black fluid wouldn't run back into the reservoir. Agreed, great video.
@jimmysnags5985
@jimmysnags5985 4 жыл бұрын
Hey Brian thanks as always your advice is spot on. My repair of power steering on 11 year old FORD Escape. Identifying your PS leak is important and saves time and money. The source of leak was the PS Pressure Sensor on the side of the pump. It was cracked result of 11 years of heat exposure. At the base of the Electronic where it fuses to the brass screw-in body of the equipment was a noticeable crack in the plastic. The subsequent fluid leak was confined to the passenger side and the front of the engine not near any steel supply lines or return. So, in conclusion check this little device first. All PS lines and the pump were in good working order. However I replaced the Pump, Return line from Steering Valve and Supply Line to Reservoir from Steering Valve. Flushing the PS Pump had a problem until dead motoring the steering wheel to full lock both side about eight times. Flushing successful I bled the air out with full RPM, and no problems or noises. Thanks Jimmy
@boots7859
@boots7859 3 жыл бұрын
I usually watch another Eric guy's video's, however was happy to find you. PS drain and replace is actually pretty easy for the average guy/gal/home-gamer. I do rather like your tip about disabling ignition to not run the pump dry. Can't believe people are still getting scammed with all these 'flushes' in 2021....
@Medmanutdfan
@Medmanutdfan 6 жыл бұрын
You are the Man!!! Just saved me a lot of money on my 01 sable... Powersteering been out for almost 3 years. It feels brand new
@jimmyross4352
@jimmyross4352 6 жыл бұрын
Ford tech Makuloco. Thank you for the procedure, very helpful. I was able to do this by myself using you're clear plastic hose idea after changing the steering rack in my 07 Freestyle, and it worked great. I also took Mike C's advice and turned the wheel to flush the (Used, Pull a part) Rack out. Thanks to both of you !!
@insomniagamer4638
@insomniagamer4638 6 жыл бұрын
Changed the power steering pipework on my focus at the weekend, then used your method to flush the system afterwards. Worked a treat!! Great vid. Thanks 👍
@joevasquez1776
@joevasquez1776 5 жыл бұрын
I just Turkey baster the reservoir out once a year and do a partial fluid change. I never want air in it. Good video
@ismann9148
@ismann9148 9 ай бұрын
Reservoir holds like 1/8 of all the fluid. Even after doing that three times, you'd be only replacing about 1/3 of the fluid and each time, removing clean fluid with it. You won't introduce air with this method unless the reservoir is low enough to suck in air.
@patneil6844
@patneil6844 5 жыл бұрын
I have a 1994 Ford Escort. After watching this video I flushed out the brown power steering fluid using this technique. Fairly easy, even though I have never done a power steering flush before. Luckily, I wasn’t having any problems. I hope the new pink fluid prevents any future issues.
@louisrosa5197
@louisrosa5197 5 жыл бұрын
my steering in a 90 windstar sounded like it had rocks in it and was very difficult to turn. I did the change as described above. It now runs fine. I want to thank you so much as you saved me from scrapping the vehicle. thank you again
@timhiller1029
@timhiller1029 5 жыл бұрын
Love your videos, always very helpful, I’d probably jack up the front tires off the ground so there’s not so much friction when going from lock to lock, thanks
@mikec9619
@mikec9619 9 жыл бұрын
You must remember that there is oil inside the steering gear, and without actually turning the steering wheel while flushing you are not flushing this out. The pinion valve only opens while turning, so you are not flushing out the old oil in the gear. Part of the flush must include a complete right turn to lock and then a complete left turn to lock. I would recommend after you see the clean fluid from the hoses, run the starter while turning the wheel to lock right (hold it tight right for a second), then run the starter while turning to lock left (hold it tight left for a second). Repeat if needed. There is normally about a 1/2 quart in the gear at all times.
@mareksumguy1887
@mareksumguy1887 6 жыл бұрын
In the "gear"??. You mean the RACK??
@brandonward2619
@brandonward2619 6 жыл бұрын
same thing. either or.
@jimmyross4352
@jimmyross4352 6 жыл бұрын
+Mike C Thanks for the advice. After changing the steering gear in my 07 Freestyle, I took you're advice and turned the wheel as per you're instructions to flush the (Used, Pull a part) gear out.
@knocksensor3203
@knocksensor3203 6 жыл бұрын
Mike C That’s right 👍
@rogercox6755
@rogercox6755 6 жыл бұрын
Mike C qw
@enigmaone7055
@enigmaone7055 Жыл бұрын
Another great video sir! Just performed this service on my wife's 13 Ford Edge, and my 14 Ford Edge. Your procedure worked perfectly. Thank you!
@checkthatmeat
@checkthatmeat 8 жыл бұрын
I have not done it this way before, normally what I do is have the same set up but I jack the front of the vehicle up and just turn the wheel back and fourth to pump the fluid out and keep filling the reservoir also. The vehicle is off the whole time also.
@corndog2835
@corndog2835 4 жыл бұрын
That what I do, it actually pumps everything out of the rack better than cranking the engine.
@alb12345672
@alb12345672 9 жыл бұрын
Did this on a relatives 95 conti. It called for type F fluid(anything pre-96 requires Type F - nothing from Ford changes that). The pump was very noisy and he got an ungodly estimate to replace it. After 15 minutes and 3 qts of type F it is quiet as a mouse for weeks. I also pulled a vac, made an adapter from a rubber cork. I pulled the PCM relay because it was easier. So, if you are hesitating to do this procedure and have an older Ford- do it NOW! This fluid does wear out! Don't know if the noise was from the air or just 150K mile fluid but probably 50K is a good interval for this service.
@mcnamee30
@mcnamee30 10 жыл бұрын
I found after you go lock to lock a few times, turn the engine off and suck the fluid out of the reservoir and replace it with fresh fluid it helps get the air out faster.
@richemmrich1858
@richemmrich1858 5 жыл бұрын
I did this to my 2002 Explorer (270,000 miles) and it worked great! Thanks for the tip.
@dneitzke
@dneitzke 6 жыл бұрын
Hey, thanks for your video effort. but what I do is just take off your return line and have it dumping into your waste oil can, and with the engine nice and warm, (With 2 people ) just run your engine , and while continually adding fluid, turn that steering wheel back and forth .at least 5 -6 times block to block, and watch that witches brew drain out, until you see perfectly clear fluid dumping out, and there is no chance of any air issues as long as you don't let that reservoir get to low, then just let it run till full operating temp.and adjust your level, I've done this at least a 100 times and never had a problem. But thanks for sharing your abilities.
@johngraham4157
@johngraham4157 5 жыл бұрын
best flush video ever,you rock dude.....going to do my Sierra and Mustang this week and add a filter to my truck....
@nicknicu1787
@nicknicu1787 10 жыл бұрын
Excellent job man! That's the way to properly do it! You never run the pump dry this way!
@nicknicu1787
@nicknicu1787 10 жыл бұрын
Also,have been meaning to mention that your camera work(lighting,angle and focusing) is excellent! I've been noticing that watching plenty of videos since I've discovered your channel a few days ago. That,combined with filming in a dealer shop environment where you're pressed by time,plus the editing work require a huge amount of effort! Your effort is much appreciated! Keep up the good work man!
@mannyroias3392
@mannyroias3392 6 жыл бұрын
Great video. On my car i just jack up the front end then remove the return hose put a container under it all and w the car off turn the steering wheel and filling with new fluid.
@AKJeeper
@AKJeeper 5 жыл бұрын
Something I do on vehicles where the crank position sensor is hard to access (late model 5.4L 3V) - put the vehicle in clear flood mode (accelerator pedal all the way to the floor, hold it there prior and during cranking). This cuts the fuel injectors off, so the engine won't fire. This doesn't always work, so test it out before doing the fluid flush.
@t.f.6623
@t.f.6623 7 ай бұрын
Thank you for your videos. They have helped me so much as a Ford owner.
@unclemarksdiyauto
@unclemarksdiyauto 3 жыл бұрын
A good reminder for all of us to change our power steering fluid! My wife's Dodge Caravan is due! So are our other 2 vehicles. Guess I have more items to do on that honey do list!
@seannot-telling9806
@seannot-telling9806 5 жыл бұрын
Also if you have a system that is a Hydroboost you need to change things a little bit. You have two fluid return lines to the reservoir. So if you just remove one you get dirty fluid in the clean. So remove both and plug the two connections and extend both into a dump can. Then step on the brake peddle a number of times while your doing this. Clear hose in this would be nice to see when the fluid is getting removed. The hydroboost assembly has an accumulator that holds some fluid. So when you firts get things hooked up and step on the brake you will see a load dump out even with the engine off.
@lucasbalyeat8746
@lucasbalyeat8746 4 жыл бұрын
Just flushed my power steering fluid on my 2013 edge. Your method worked great. I had my kid crank it over for me while I added fluid. My engine light came on now, I'm sure it's from unplugging the crank sensor. My question is will it go off by itself or should I reset it? Thanks again for the very in depth and well put together video.
@JasonSmith-qx3zh
@JasonSmith-qx3zh 3 жыл бұрын
How many on the average did you go from lock to lock to bleed tje system of air???
@bojo8141
@bojo8141 Жыл бұрын
Great video, very informative. I really appreciate how much detail you put into your videos.
@charleshines6155
@charleshines6155 5 жыл бұрын
I would use a clear tube for this just to see when the fluid starts to become clean. I use CHF-202 in my Volkswagen and that stuff is not cheap. This stuff is very thin and has a high viscosity index of 302. Just look at ATF and most don't come close to that. A high viscosity index is often a sign of a synthetic oil but not the only distinguishing characteristic of such fluids. The way you are doing it seems to be a good way to keep air from getting in as long as the car does not start (would drain the reservoir much quicker and suck air in). I know it is very similar on most vehicles and an just looking for the better way to do mine since mine is due for a change. I might even check the screen in the reservoir to see if it should be cleaned out. You would be surprised how dirty they can get but that screen hopefully prevents the worst of it from getting in the pump and rack. I say the worst of it because no screen is going to stop 100% of all nasty stuff from getting in but it is a lot better than no filter at all. In a vid about changing the fluid on a Mercedes I saw they have a removable cartridge filter which looks like the element you would find inside an oil filter. It even has metal caps like the element you would find in oil filters. I only know because I was looking to see how everyone else is doing theirs and it is mostly similar with the return line redirected to a container and the wheels off the ground to allow easy turning of the steering wheel to purge the old fluid while adding new to keep air from getting in.
@Passionate747
@Passionate747 7 жыл бұрын
Excellent video I like it I have the 2008 BMW 750li the power steering was leaking very small drops of fluid , I purchased the power steering sealer that didn't help much , After watching your video it was very easy to flush the steering system. I flushed it with Castrol transmission oil with 3 quarts worked perfect but I let the car run while the old fluid was draining out to 18 liters empty paint pail, Now my car runs fine it took me 1 hour to complete . Thanks for posting it helped me a lot.
@ScubaCat3
@ScubaCat3 6 жыл бұрын
I spent more time than I care to admit chasing down the whine noise and that stupid screen was blocked with sludge. A shot of carb cleaner fixed it right up. Nice little secret filter there.
@hajileserpud9539
@hajileserpud9539 5 жыл бұрын
Won't carb cleaner in steering system break your pump and give steering issues after some time ?... or did you remove screen and then clean ?
@charleshines6155
@charleshines6155 5 жыл бұрын
You had sludge? Did you use the correct fluid and not mix two types of fluid? I saw a vid on a Audi and someone topped it off with one of the wrong fluids and it was like it had been filled with grease the way it reacted in there. It wouldn't surprise me even one bit if he had to replace his whole power steering system rack, pump and hoses. It probably caused problems with his rack and pump later on. This does not end well when it does happen because replacing those parts can be really expensive.
@hajileserpud9539
@hajileserpud9539 5 жыл бұрын
@Wayne Jorgensen ok that's understandable...
@winstonsmith3685
@winstonsmith3685 3 жыл бұрын
Your videos are great. Perfect amount of explanation. Some guys over explain the hell out of everything.
@bentnickel7487
@bentnickel7487 3 жыл бұрын
It's obvious, from the hundreds of unanswered comments, that you can't over explain any procedure. People have various levels of mechanical knowledge and experience. You want to know, just so much, until you get confused. Others, need more knowledge, as it relates to other systems within the car.
@johnballard9770
@johnballard9770 Жыл бұрын
Great video! I just did my 2010 Expedition using this info. Thanks!
@schGjS
@schGjS 2 жыл бұрын
Good procedure but I would add that on many reservoirs, including my Freestar, there is a fine screen that gets plugged. I removed as much fluid with a syringe, removed the reservoir from the three grommets (rotate out from the bottom slip in grommet), remove the hoses, then thoroughly cleaned the reservoir and internal screen. I temporarily put the reservoir back in place with a cap over the small return fitting, the Freestar the return fitting is hard to get to so after the procedure. When the procedure was complete, I did have to syringe out fluid again and tip the reservoir to reattach the return line. I did a slight alteration on your procedure, rotating the steering while cranking to get more of the dirty fluid out of the rack. No air in the system when complete and you could see good pump flow in the reservoir when complete.
@nmoz091
@nmoz091 Жыл бұрын
I tried this today with my new PS pump. It did not work. It did however result in a broken CKS pigtail clip. So now that won’t stay plugged into the sensor. I ended up turning the key to the accessory position and cycled the wheel back and forth. That worked the mercon v through the system and it did great. Hooked everything back up, wedged a pry bar against the sensor, started the truck and cycled the wheel back and forth while my vacuum pump was hooked up. Did 2 separate rounds of that and got all the air out. Tomorrow I’ll splice in a new CKS pigtail and hope it’s all good.
@sglenn6
@sglenn6 4 жыл бұрын
Great Video! You spoke about the screen filter being dirty. What do you do if it is dirty? Can these be replaced without replacing the whole unit? Thanks
@stevesykes9696
@stevesykes9696 6 жыл бұрын
Great video. First time I tried something like this and was pretty strait forward. Thanks
@garyclark8891
@garyclark8891 9 жыл бұрын
Thank you sir. I appreciate the feedback. ..
@garyclark8891
@garyclark8891 9 жыл бұрын
Should be good ? 2007 f-150 I'm asking u because u seem to know a lot about fords. I just don't want to screw anything up... Thank you sir for ur response. ..
@FordTechMakuloco
@FordTechMakuloco 9 жыл бұрын
The mercon v is also a synthetic so you will be fine
@andyprairiedog
@andyprairiedog 5 жыл бұрын
Excellent. Was wondering how to 'disable' the vehicle to only crank and not start. Very helpful. Thank you.
@carlwheeler3403
@carlwheeler3403 5 жыл бұрын
Great video. I replace the power steering fluid and brake fluid with every oil change. I suck it out of the reservoir and refill it. Its an easy process and it provides new fluid at shortened intervals.
@NFLYoungBoy223
@NFLYoungBoy223 5 жыл бұрын
Carl Wheeler that’s very unnecessary
@discerningmind
@discerningmind 6 жыл бұрын
Great video! I've never seen this method, and being completely impressed with you I subscribed.I thought turning the steering wheel while stopped with the full vehicle weight on the tires caused damage. I only turn my steering wheel when my wheels are rolling, even if just inching along to get out of parallel parking. Am I wrong?
@FordTechMakuloco
@FordTechMakuloco 6 жыл бұрын
They can handle that and a whole lot more.
@discerningmind
@discerningmind 6 жыл бұрын
Thanks.
@174joedirt
@174joedirt 10 жыл бұрын
thank you for doing a windstar video
@alm7707
@alm7707 6 жыл бұрын
Great job.That does work on some. Now show us how on a mid 2000's f150 5.5l. bet on that one you do the suck and fill through the fill cap. You are turning the steering wheel while you crank?
@qualitytools8116
@qualitytools8116 4 жыл бұрын
I used this method after watching your video on my 03 Ranger 3.0, also replaced a leaky low pressure hose, worked great! Thanks. Any tips on how to replace the seal or O-ring on the large nut that is right up against the power steering reservoir, not the one that has the high pressure line (I saw that video and changed it it was spot on) but the larger nut that the nut of the high pressure hose goes into as mine leaks. Thanks for helping so many of us out. Great information and very educational videos as always. Hope to hear back from you :)
@almfreak
@almfreak 7 жыл бұрын
got an Explorer and Excursion that could both use this. thanks for the tip!
@merrillschaps2325
@merrillschaps2325 3 жыл бұрын
This was the simplest video on how to completely flush your power steering system I have seen yet! I did this to my '07 Lincoln Town Car and it worked extremely well. Question; Is the power steering pump supposed to stop working after you exchange about five quarts of Motorcraft Mercon V transmission fluid?
@YeOldeGeezer
@YeOldeGeezer 3 жыл бұрын
You have air in the system
@markbulva4188
@markbulva4188 Ай бұрын
On my long lost 04 that had a whiney pump at 100k kilometers. I dumped the fluid and replaced factory oil with Amsoil and pump was quiet and responsive 8 years later at 424k kilometers
@reefaddict6137
@reefaddict6137 3 ай бұрын
I use a small pump that hooks up to my battery. Sucked out the reservoir, took the hose off and stuck the pump hose down the power steering hose and sucked down to the pump😊 get the pump, easy! 20 mins
@rifrox8866
@rifrox8866 3 жыл бұрын
Very helpful video for this non mechanic to get it done.
@whistle3man
@whistle3man 2 жыл бұрын
I love your channel. You have helped me so many times on my f150. Thanks for making the videos.
@paulrhodes482
@paulrhodes482 6 жыл бұрын
Great video thank you for all the great tips have really enjoyed your channel for severl years now. How much Mercon V do you recommend I order for this flush 2006 Ford F-1505,4 L? Also what brand and model hand pump did you use with the resivoir cap adapter would like to get that set for my shop. Thanks again have a wonderful weekend. -Paul
@jdub8812
@jdub8812 6 жыл бұрын
I used this method on my ford focus and it worked amazingly well. I now have a Subaru outback and am wondering if this same method would work on a foreign vehicle??
@johna7287
@johna7287 5 жыл бұрын
If the Subaru had electric power steering than no. But the procedure is the same i think if it requires fluid
@emorris272
@emorris272 10 жыл бұрын
Thanks for the video! I always wanted to change the fluid but didn't think just draining the reservoir would do much good!
@bransonbrendan226
@bransonbrendan226 3 жыл бұрын
I guess Im asking the wrong place but does anyone know of a way to get back into an instagram account? I was stupid forgot the password. I would love any assistance you can give me
@gagemorgan8139
@gagemorgan8139 3 жыл бұрын
@Branson Brendan instablaster =)
@bransonbrendan226
@bransonbrendan226 3 жыл бұрын
@Gage Morgan Thanks for your reply. I found the site through google and Im waiting for the hacking stuff atm. Takes a while so I will reply here later with my results.
@bransonbrendan226
@bransonbrendan226 3 жыл бұрын
@Gage Morgan It worked and I now got access to my account again. Im so happy! Thank you so much, you really help me out !
@gagemorgan8139
@gagemorgan8139 3 жыл бұрын
@Branson Brendan happy to help =)
@romeomaloco3180
@romeomaloco3180 7 жыл бұрын
what did you use to block the small pipe in the reservoir?
@Vercus100
@Vercus100 6 жыл бұрын
I have a 2001 Grand Marquis, and am thinking of doing this. However, for mine the belt is easy to remove, so I thought of just removing the belt and turning the pump by hand. That would save wear and tear on the starter, as well as let me see what's going on better. Something to consider on RWD based platforms.
@paulrhodes482
@paulrhodes482 6 жыл бұрын
Where can I get the cap you used to cap off the power sterring resivoir where you diconnected the line? Thank you for all the amazing videos have a blessed sunday.
@paulrhodes482
@paulrhodes482 6 жыл бұрын
therockkkkher thank you very much for the help have a great night.
@paulrhodes482
@paulrhodes482 6 жыл бұрын
therockkkkher perfect thanks again for the great help
@paulrhodes482
@paulrhodes482 6 жыл бұрын
therockkkkher sounds like a great idea let me know thank you
@tomday8352
@tomday8352 Жыл бұрын
Tried this today on 2017 F250 with 46k on the clock and not having any issues just doing for maint. .. all it did was make a mess out the top of the res., nothing out the hose into bucket... figured I had the hoses swapped so I set it up off the other hose and capped its port on res..... still nothing out the hose to bucket... gave up. at least I got the old fluid out of the res. and those 2 hoses... refilled with fresh Mercon LV and went lock to lock. no noises and steering fine. oh well at least I got some new fluid in there.
@fredbach6039
@fredbach6039 5 жыл бұрын
When I do this, I jack the front wheels off the ground and I have someone turn the steering wheel lock to lock while the fluid is being pumped out.
@BigJBouncer
@BigJBouncer 6 жыл бұрын
Thanks for the video, it's really helpful! I'm a new subscriber and love how informative your videos are! I just ordered a MityVac and the good metal extension tool you used. Had a quick question about MERCON though. I have a 2004 and 2010 Mercury Grand Marquis. The Haynes manual says 1996-2008 models should use MERCON and 2009 and later should use MERCON V. Should I stick with those recommendations from Haynes, or is MERCON and MERCON V interchangeable in this case? Would I be able to use MERCON V in both of my cars? I don't know what the difference between the two are? If MERCON is the route I should go for the 2004 do you want to add an Amazon link so I can purchase through your store? Thanks in advance if you are able to reply!
@ReginaJannie
@ReginaJannie 3 жыл бұрын
Mercon V is retro capable and is the best latest technology. Valvoline Max Life Full Synthetic ATF supplies Ford. Get it for $17 a gallon at wally world free shipping over $35 spent.
@sweetbrandigirl
@sweetbrandigirl 5 ай бұрын
I wish you had a video on how to dod this on a Mustang GT 2009. I really don't want t remove the A/C compressor just to unplug the crank sensor.
@Nessal83
@Nessal83 3 жыл бұрын
Seems a bit rough on the starter. Can't you just turn the wheel lock to lock to flush it?
@harleydavidson9127
@harleydavidson9127 4 жыл бұрын
Nice work...Keep up your awesome videos. Thank You
@louhess6355
@louhess6355 7 ай бұрын
Great video thank you. Can you make a new video Super duties 2020 models on power steering flush and fill. No one has one on the KZbin . Thanks so much you're quite informative.
@richardmellem3583
@richardmellem3583 4 жыл бұрын
Good video, just a couple things.... Why do you disable the ignition and use the starter motor instead of just letting the motor idle ? If you do a better job of keeping the reservoir topped off you won't get so much air in the lines. Also, I believe that Mercon V is a synthetic blend and not truly "full synthetic". Never the less, still the best to use.
@FordTechMakuloco
@FordTechMakuloco 4 жыл бұрын
I follow the Ford procedure and it works very well with no chance of damage to the customers car. If you have a helper and the perfect funnel and someone to pour as fast as it pumps then go for it. Be prepared for a mess though and possible pump damage....
@maniacmikef3348
@maniacmikef3348 6 жыл бұрын
Yu make awesome videos really detailed and very helpful, thank you.
@libertyrich555
@libertyrich555 5 жыл бұрын
Suggestions on how to clean the reservoir screen would be appreciated .
@rockyfish3115
@rockyfish3115 5 жыл бұрын
You need to remove the reservoir for that
@ianhall6203
@ianhall6203 4 жыл бұрын
Quick question, I was reading the comment down below and saw that you recommended Mercon LV to someone who had a 2015 Ford F150.... I have a 2013 Ford F150 Lariat 5.0 Should I use the Mercon V that you have listed, or will my vehicle require Mercon LV. Thank you again for your videos!
@frankrumble6754
@frankrumble6754 6 жыл бұрын
I got only two hoses on my Ford Tempo... but you mention three hoses...Big hose.., the 3/8 hose and the other hose you use to drain
@David-yh5po
@David-yh5po 3 жыл бұрын
Thanks for sharing this video with us. I don't have a Ford but looking to save money. What fluid do you suggest on a Honda accord 2020 in the future?
@ralphderkapitaen9875
@ralphderkapitaen9875 7 жыл бұрын
thanks for the video. How do you know, the air is completally bleeded in the final stage, when you keep turning the wheel from lock to lock? I know you wait for the bubbles...but when do we know 100% all the bubbles are really gone? can it be that the bubbles arent coming out anymore for a while, and then they pop up again? thx
@manonfire3642
@manonfire3642 3 жыл бұрын
Can this be used in ford transmissions too (Mercon V)?
@hiramadu-kusi4096
@hiramadu-kusi4096 4 жыл бұрын
Great video. Just wondering, why do you crank instead of starting the car fully? Does this method work on a Lincoln LS? My power steering fluid is kinda milky.
@mwendia
@mwendia 3 жыл бұрын
This is the same question I have. If the purpose of cranking is to turn the power steering pump, why not just let the car run and then you dont need to hold the key and listen to the cranking?
@BrentCizekPhoto
@BrentCizekPhoto 5 жыл бұрын
Thanks for the video. What was the cap that you used to temporarily cap the port of the reservoir?
@kas0016
@kas0016 4 жыл бұрын
Looks like ac new component port cap. Nothing fancy
@shaunhuckabee5904
@shaunhuckabee5904 5 жыл бұрын
Is this process the same for a power steering pump change? Great vid by the way!
@anthonyerdman1725
@anthonyerdman1725 5 жыл бұрын
When you were bleeding the air out using the lock to lock method did you leave the cap off the reservoir? Also great video!! Thanks 🙏
@FordTechMakuloco
@FordTechMakuloco 5 жыл бұрын
cap off yes
@anthonyerdman1725
@anthonyerdman1725 5 жыл бұрын
Thank you for your very informative and helpful videos. You “ROCK BUD” please keep them coming.
@jackwilson4722
@jackwilson4722 2 жыл бұрын
Hey good video. I did want to point out the cost of the fluid .4 quarts of mercon 5 is like 40 some bucks..seems quite a bit just to flush a system that only hold less than a quart..
@moneymac2864
@moneymac2864 7 жыл бұрын
Will removing the crank sensor prevent all vehicles from starting? I.e. Toyota
@marketingmajor8126
@marketingmajor8126 5 жыл бұрын
Just pull the fuel pump fuse.
@syfiltzo
@syfiltzo 4 жыл бұрын
@@marketingmajor8126 If you dont remove fuse, just let engine work idle and watch to refill reservoir while getting low level... is this wrong?
@jeffreyverry7151
@jeffreyverry7151 2 жыл бұрын
Great Video. Very Helpful.. TY
@ianhall6203
@ianhall6203 4 жыл бұрын
Thank you for your Ford videos again! Have you noticed any issues with the power distribution box in newer Fords? Is there any maintenance that can be provided with steering since the fluid aspect is now removed?
@spicyhot1695
@spicyhot1695 3 жыл бұрын
Another great and informative video from you Makuloco. Would this procedure work on Lincoln MKX? Thanks for sharing
@CollegeRecruitsNW
@CollegeRecruitsNW 3 жыл бұрын
Yes! 99 5.4 F150, I recommend high compression clear 3/8 line, my Hardware Sales .45 cents a foot compressed, crimped over any bend. I fixed the crimp, fluid flowed. I recommend 8 ' of transfer hose. With all said, Wow Brian! I had little flow, actually pumped up, what may that say? Thanks as always!
@Lsailor169699
@Lsailor169699 4 жыл бұрын
Great vid. Did you use Mercon V for the flush? Best, The Sailor
@courtneyprovance8448
@courtneyprovance8448 4 жыл бұрын
Lsailor1 he said yes , Mercon v
@alonsocalderon9866
@alonsocalderon9866 4 жыл бұрын
Great video! Do you also have a video on how to flush coolant system?
@FordTechMakuloco
@FordTechMakuloco 4 жыл бұрын
Yes
@jagoss45
@jagoss45 7 жыл бұрын
Where is the crank position sensor connection on the 5.4 triton???
@FordTechMakuloco
@FordTechMakuloco 7 жыл бұрын
passenger side of the crankshaft pulley you will see a sensor with a connector that is it.
@NickAbatino
@NickAbatino 3 жыл бұрын
Great video, easy to follow. Subscribed, thank you!
@michaelbefumo-qg7ji
@michaelbefumo-qg7ji 11 ай бұрын
Brian I can do that same method on my 08 expedition
@joemartinez6182
@joemartinez6182 5 жыл бұрын
Keep making video, its helped me a lot.
@wasteoftime441
@wasteoftime441 7 жыл бұрын
Great video, on,y thing I did different was raise truck off the ground so I didn’t wear a spot on my 37” tires.
@Kyle-cv3de
@Kyle-cv3de 4 жыл бұрын
HM WHAT SIZE ARE YOUR TIRES? IM SURE IT'S NOT A PAVEMENT PRINCESS
@OsceolaFrisbee
@OsceolaFrisbee 5 жыл бұрын
Great vid Brian. I flushed the power steering fluid on my 06 F150 Triton 5.4, but still have what looks like "boiling" in the reservoir. Is this heat, and actually boiling, air in the sytem? or a blocked line of some kind? Thank you for help.
@benson4u215
@benson4u215 5 жыл бұрын
Trapped air pockets
@joeh690
@joeh690 4 жыл бұрын
Can't you do the same procedure but only Jack the wheels up and turn the steering wheel manually. I would rather not stress my starter by doing this or power steering pump
@kevlinville
@kevlinville 6 жыл бұрын
Loving this video. Schedule to do this on my 09 Escape. Does the crankshaft switch operate th same way on all vehicles (IE 2009 Murano)?
@Abos6am2
@Abos6am2 3 жыл бұрын
i Flushed my f350 2011 6.2 Power Steering System doing like what you did but i Poured 0.5 qourt extra to clean while i was moving it lock to lock then i replug the hose and burb the air out but !! after that i got a small pit of whine feel when turning to the right ben 6 month and still
@drome010381
@drome010381 2 ай бұрын
Can you fill the power steering on the f350 using the capri brake bleeder? Using the return line after the booster
@d.e.b.b5788
@d.e.b.b5788 9 жыл бұрын
Well, it's obvious that Ford does not make their own fluids. So, what we have to find out, it who makes it for Ford. Theirs will be the same as the Mercon V in the nice Ford labeled container without the nice higher Ford price. If anyone knows, please update us here, I will search as well.
@justinp8946
@justinp8946 8 жыл бұрын
I got mine at Walmart
@Skauber
@Skauber 7 жыл бұрын
Mobil1 has a great fully synthetic Mercon V compatible fluid. That's a quality brand, and can't imagine it would hurt anything that is specced for Mercon V. The system doesn't really care if it says "Motorcraft" on the container or not.
@caseyrandell724
@caseyrandell724 4 жыл бұрын
Flushing the power steering unit helped me alot the only thing is it didn't show me how to change the power steering hose or the screw that screws into the power steering unit of a AU3 tickford xr6
@timliphardt5125
@timliphardt5125 3 жыл бұрын
Can i use Mercon V in a 2013 F150 for power steering fluid change ? Thank you
@donaldm4846
@donaldm4846 4 жыл бұрын
Hi. Great channel. I have a 99 ranger 3.0 changed the pump due to noise and wheel hop feel during steering. New pump or re-man pump is better but sounds noisy? No leaks fluid full and ran vac cap to bleed. Are these just noisy models??
@luckyfulk6894
@luckyfulk6894 2 күн бұрын
Hey man I have a 03 ford windstar. I believe I put reg ps fluid in it after put on a new pump. Question is would the reg fluid cause the steering power to come and go.definitly going to do the flush you demonstrated first but do you think i should I replace the steering rack too
@maximusvonce1381
@maximusvonce1381 Жыл бұрын
I think draining the reservoir yearly should be adequate in keeping fluid pretty clean. No need for complete flush pump out.
Power Steering Flush and Reservoir Cleaning
44:55
Timmy The Toolman
Рет қаралды 317 М.
Nastya and balloon challenge
00:23
Nastya
Рет қаралды 57 МЛН
🍉😋 #shorts
00:24
Денис Кукояка
Рет қаралды 2 МЛН
The Most Important Step BEFORE Performing Any Brake Job
8:30
FordTechMakuloco
Рет қаралды 580 М.
Absolute BEST Method To Flush Power Steering Fluid!!
8:26
Power Steering System Air Bleed Process
5:30
Garage Gurus
Рет қаралды 737 М.
How to Flush Your Power Steering Fluid
6:51
ChrisFix
Рет қаралды 5 МЛН
#1 Way To EASILY FLUSH YOUR POWER STEERING SYSTEM!!
8:56
1ROAD
Рет қаралды 208 М.
Will a barrel of engine flush clean a sludgy engine?
12:54
Garage 54
Рет қаралды 1 МЛН
How to Change Power Steering Fluid in 5 Minutes - DIY Easy
6:11
Silver Cymbal
Рет қаралды 2,1 МЛН