How To Test 3 Pin Primary Ignition Coil DIY

[@ERICAUTOCENTER]

*Thanks for watching and share to reach many people

[@gyanato4458]

Powerful video content keep them coming sir 💯 pure informative

[@ERICAUTOCENTER]

Appreciated

[@ryankislingbury9178]

Hi im testing a similar 3 pin ignition coil, the right side is power in, the middle is negative/earth and the left pin is trigger. When testing using 200k ohm reading, earth pin to power pin = no reading, earth pin to trigger pin = 1.7 - 1.8 reading. These readings are the same on all 4 ignition coils, am i correct that these coils are dead and broken????

[@ERICAUTOCENTER]

Are they primarily ignition coil?

[@ERICAUTOCENTER]

If not use mega ohms but testing them doesn’t solve the problem depends on how they perform on the engine so troubleshooting first before buying a new coils if you have similar coils on different car swap them if the problem exists check harness conectors. It’s sometimes happens to be the ECU but do proper diagnosis before troubleshooting. I hope my explanation finds you well.

[@ryankislingbury9178]

@@ERICAUTOCENTER just a single coil pack exactly like you got but for a fiat 1.8 16v engine.

[@ryankislingbury9178]

@@ERICAUTOCENTER I have retested the coils on all ohms settings between Earth and power pins and no readings what so ever, only readings are trigger to earth pins and again 1.7-1.8 so I'm guessing they're dead and will order replacements as I don't have spares

[@ERICAUTOCENTER]

@ryankislingbury9178 they’re dead no continuity

[@neostarfromearth107]

Thank you Eric, nice lesson !

[@ERICAUTOCENTER]

Glad you liked it!

[@raymondmpisane9798]

Please post a video for one 3 pin single coil pack.

[@ERICAUTOCENTER]

Ok that’s fine I will do that

[@lawsonlavia278]

How much a good ignition coil should read

[@ERICAUTOCENTER]

It depends the type of coil base on the engine capacity whether 3 cylinder, 4 cylinder, or v6 & v8 type but the ignition coil reads from 0.94, 0.01, 0.02 or more and finally some also read from 1.02 or more and all this means there is a continuity which means the ignition coil is good

[@lindolphmurray9480]

Thanks for the video but u need to raise your voice a little so we can hear u more clearly

[@figgiefigueroa7372]

The multi meter number to be set ????

[@machinemods]

Where do I connect the Tachometer wire?😊

[@nhubui1602]

Thanks for the video . ❤

[@ERICAUTOCENTER]

Welcome

[@aliautomotive]

Just checked with brand new coil ,totally wrong readings.showin 1300 to 1800ohms on one pin only.

[@ERICAUTOCENTER]

Then you can check it well it shouldn't be like that. there should be continuity it is the way you're using your multimeter. Dont delay too much time on the multimeter it will trigger everything and can burn your new coils

[@insane_eddie_7257]

What is the proper reading on a 2006 Chrysler 300c with a 5.7 motor can you help me please

[@ERICAUTOCENTER]

Please come out again with your question and let me help with the answer I can’t get you clear. Explain further

[@insane_eddie_7257]

@@ERICAUTOCENTER im trying to test my coils but I don't know the exact readings

[@ERICAUTOCENTER]

Oh ok a proper reading must start with 01.0ohms I have done a full video for premier today at 2pm local time stay updated.@@insane_eddie_7257

[@travelservices740]

sir whould you please reply in vedio that if reading is more then 26.9 means 35.09 or 45.09 then the coil ok or not correct rating of 3 pin ignation coil is what

[@ERICAUTOCENTER]

Check in the comments section I have replied many on this same question thank you

[@ericdarko5479]

Thank you

[@ERICAUTOCENTER]

Welcome

[@yohaneswoldemichael5117]

much powa to you

[@adegokeo.johnson3163]

Checked mine and is showing 51.6

[@ERICAUTOCENTER]

51.6 means there is no continuity the ignition coil is bad. If the resistance show 0.01 on the multi meter this means there is continuity then the ignition coil is good. so have to buy a brand new set of coils

[@DavidMartin-vs2sr]

Might want to learn King's English

[@ERICAUTOCENTER]

Yes i

[@anwaralibana6786]

please translated in urdu