Thank you for posting this video. I appreciate the short and to the point instructions
@4DIYers9 ай бұрын
You're very welcome and thank you for the kind words!
@FrankBenlin3 жыл бұрын
Wow, someone with a check mark that actually answers viewers questions. Good job, thanks.
@4DIYers3 жыл бұрын
Thank you so much! I try my best to get to all the questions asked.
@silvanaribeiro8168 Жыл бұрын
This video is good only if you already know how to use a multimeter which is not my case. It would be to have an explanation of how to set up and turn the multimeter on.
@AndyNav1 Жыл бұрын
Thanks for the video. The single filament bulb I have, doesn't light up on the car. When I took it out, noticed the glass has some black sooth on it, however, there is continuity. What is your diagnosis for this bulb please. Thanks.
@4DIYers Жыл бұрын
Black sooth sounds like it’s burnt out.
@davidm32102 жыл бұрын
The resistance readings that I get from my headlight are not in line with the manufacturer specs and don't even compute with my amperage readings (about 4.7 A at 14V) according to Ohm's Law. Any idea what I am missing? Thanks again for the tutorial.
@Solutionist16 жыл бұрын
Concise, clear video. Cheers mate
@4DIYers6 жыл бұрын
Thank you!
@keithfernandes1834 жыл бұрын
Nice. straight to the point.
@4DIYers4 жыл бұрын
Thank you!
@comachocomacho65815 жыл бұрын
hi, my bulb low beam is not working, but the high beam is working fine. I want to know how where to put the multi meter connectors to check each low and high beam thank you Tony
@cooldude224511 ай бұрын
I have a car lightbulb that filament intact, so I tested continuity and no. Only think I think is the lead? Pointy part wore out?
@chrisorourke33634 жыл бұрын
How do you test a halogen tube type bulb all by itself? The kind that sorta look like a neon tube. Thanks for posting this helpful video.
@davidm32104 жыл бұрын
To make sure that your m.m. is functioning, it's advisable to touch the leads together to check them for continuity before you begin. Also, I like to use the diode setting for the audible beep. Cheers!
@Alrashdi9 жыл бұрын
As you did in the first bulb, you said that it's not working and should be replaced. Once I did the same thing with mine by the multimeter and it shows no signal but when I plug it to a battery it works! why is that? I'm sure that I put the multemeter on 200 ohm! What do you think?
@4DIYers9 жыл бұрын
+حامد الناصر The filament could be broken, but when you apply voltage it reconnects. It's most likely on it's way out.
@jasonwight77267 жыл бұрын
thanks for the video. I have this multimeter and now how to test my bulb.
@4DIYers7 жыл бұрын
Glad to help out :)
@KnowingGodExplorers Жыл бұрын
Would be nice if you show where to set the multimeter to instead of just telling people every multimeter is different especially for beginners
@Ion1cBomberАй бұрын
If you paid more attention you would see that the multimeter is set right in front you . Maybe you want him to explain , but it right in front of your face . Just saying .
@rpmzzz5 жыл бұрын
How do you test a H3 bulb? I have it set to BEEP if there's continuity
@fvg34016 жыл бұрын
question! getting an aircraft light blub to work off 12 volts that require 28 volts? Is there an easy fix? It's a small bulb like in your video here. Here's the info on the back of the bulb (Micro lamps ML- Cage code 61951 M6363/2-2 28.0 Volts. Thanks
@Parymary-ix5db5 ай бұрын
Very Useful 👍
@zaidmemon84954 жыл бұрын
Hi, i changed brake light bulb but whne i press brake pedal, the tail light bulb glows with high power instead of glowing brake light bulb. Can you suggest what could have gone wrong..??
@4DIYers4 жыл бұрын
I saw the video you posted. There maybe a wiring issue or could have been the wrong bulbs, either before or now. I know some European vehicles have a two stage brake lights, when they're pressed normally they illuminate as they should and for hard braking, they activate another circuit for brighter lights.
@whatstheproblem66063 жыл бұрын
Prolly your bulb installed wrong
@michaelcordero55884 жыл бұрын
What's the setting on ohms? 20k, 200?
@awfullawton44702 жыл бұрын
200
@brianpacheco19278 жыл бұрын
Hey man I got one of those really skinny halogen bulbs I don't know where the connection is (I don't see any copper or metal) where should I test it? Do I need to take the socket out as well?
@4DIYers8 жыл бұрын
Yes you will need to remove the bulb from the socket. Don't forget to subscribe!
@brianpacheco19278 жыл бұрын
So my socket is only reading 0.1V at the 200volt setting on multimeter. Doesn't seem right because it should be reading 12V. Any other tests to rule out the wires and just be the socket?
@billwilson53417 жыл бұрын
Brian Pacheco: Wish there was an answer ...
@Thetrucky698 жыл бұрын
Excellent information.
@4DIYers8 жыл бұрын
+Thetrucky69 Thank you.
@Thetrucky698 жыл бұрын
+4DIYers No probs mate cheers.
@addie78462 жыл бұрын
Thanks much
@4DIYers2 жыл бұрын
You're welcome!
@GodsHerosGodsHeros9 күн бұрын
Brilliant
@ledmk25 жыл бұрын
Nice video
@4DIYers5 жыл бұрын
Thank you!
@MRFORD218 жыл бұрын
Thank you
@PBS-nm1uu4 жыл бұрын
thanks great info, i am wiser thanks to you .
@4DIYers4 жыл бұрын
Thank you :)
@marilynilagan4829 жыл бұрын
where to set the multimeter
@4DIYers9 жыл бұрын
+Marilyn Ilagan To the lowest Ohms setting.
@homerpreyer14964 жыл бұрын
Thinks on helping me lern how to check the car light
@Ebolson10199 жыл бұрын
What about the socket
@4DIYers9 жыл бұрын
+Bryan Olson I'll see what I can do for producing a video on that.