How to Upgrade to Klipper on any Ender 3 for High Performance

[@Vector3DP]

If you're mainly concerned about getting hold of a raspberry pi, get subscribed because I have a good potential solution that were going to try out!

[@paulmilne3038]

An orange pi perhaps, or the one that comes with a duck? Guess I will see.

[@xecarfa9755]

i followed your tutorial I'm running klipper on pc

[@melbatoast1985]

@@paulmilne3038 wi'll this method still work with an orange pi?

[@genoeg7]

Can yous share the ender 3 neo config file?

[@aiexzs]

i'm installing it on a thin client right now, a used wyse 5060 is cheaper than a pi 4 and more powerful + more expandable. only thing you really miss out on is the GPIO pins and full software support

[@AdrianoCasemiro]

This tutorial is a must. Brilliant rhythm, almost a speed run, but that's what the pause button is for. Currently I am on Sonic Pad + Ender 3 S1. Went the lazy way, I must confess. I can't stress this enough, Klipper is the best upgrade one can make on a stock 3d printer.

[@hd-be7di]

Klipper vs direct drive you still chose Klipper first?

[@ReinaldoJ_AF]

​@@hd-be7diI'm kinda sure that you can use a direct drive and klipper at the same time, yet, I might argue, changing the Bowden to a direct drive it's a change, not a upgrade, klipper is, in it's messy way, an upgrade

[@hd-be7di]

@@ReinaldoJ_AF Bowden is garbage. I'd rather have Marlin with direct drive than Klipper with bowden.

[@rollinthesweets6147]

@@hd-be7di The S1 comes from the factory with a direct drive setup already

[@mikel5077]

KUDOS! I now have klipper running on my ender 3 pro! you have the most complete video on doing this. I was literaly banging my head against the wall and was aout ready to give up on klipper

[@ladislavzenk2139]

I can't get my ender flashed on that 32 bit board

[@Данис-ф6с]

Thanks! Not without nearly 100 opened chrome tabs but I've managed to install klipper with raspberry within 1 day

[@yvesguenette279]

This is the best video on the subject that ties it all together. I had spent many hours on other bits and piece of older videos without success. Once I found this video, I restarted the complete install from the start and ended with a functioning Klipper for my CR10S Pro V2 in very short time. Thank you!

[@Kimkim-gl6qc]

The most comprehensive klipper tutorial ever. i didn't even realize that this most informative video even exist.

[@iamsmashy]

Great tutorial. I had trouble getting klipper to flash on my ender 3 pro with 4.2.2 board (blue screen, which is okay but I couldn't get the MCU id). After I did the following it seemed to work (3 commands): cd ~/klipper/ make menuconfig sudo service klipper stop make flash sudo service klipper start sudo usermod -a -G tty pi Found this on Klippers website about building the micro controller code. Using a different usb cord also seemed to be necessary. Hopefully this is helpful for someone else too :)

[@TheThouZands]

trieed it but still doesn't work, maybe it is because i'm in ubuntu, but i also have the same printer

[@iamsmashy]

@@TheThouZands try a high quality cable. Try like 4 or 5 before you rule it out, that prevented me before this iirc

[@TheThouZands]

@@iamsmashy had seen that problem, but i tried 6 and none worked, figured out it was a problem with the OS, there are solutions directly for debian but not for Ubuntu, and i just installed linux only for printing, so i dont know shit about it as to translate the solution, so right now im installing debian lmfaoo

[@dragosshdc]

this worked, make sure to do a "make clean" before just in case

[@JHV166]

I watched this, then I laid down for a bit to allow my brain to cool off. Possibly the FINEST tutorial of a complex system that I have ever watched. BRAVO, Thank you, and Get yourself an extra piece of pie!

[@YouBetterCallSaul]

omg thank you so much idk why your tutorial worked for me but after many tries with using an old PC running linux I got it to work. Thanks!!

[@danielbram4842]

thanks for an excellent step by step guide, just migrated my ender3 - 2018 to klipper and mainsail, didn't use a pi but an HP Thinclient T520, first print ongoing.

[@danielpereda3724]

With the Creality 4.2.2 board? I ask you because I'm having problems with it right now. I'm using the configuration provided by the video (using the Ender3v2 configuration) for the Ender 3 with 4.2.2, but it doesn't work. My Ender 3 freezes with the blue screen on. I tried using the configuration provided by GitHub, but it gives me a .elf.hex file that the printer doesn't even recognize. I'm also using a laptop

[@henrikbakk1]

Thanks so much for this video - extremely information dense, and very high SNR! Great you cover multiple methods & mainboard configs, too. Was getting ready for a new printer, but feel I got that "for free" (no new HW, just a few hours invested) just by getting Klipper (and tuning a bit). Faster *and* much better prints now.

[@Framed_Niner]

After trying many tutorials that did nothing for me, this one finally worked! I guess it was the main board that caused me so much grief, but that issue is history thanks to your tutorial. Thanks!

[@zuberio]

Just followed along with this fantastic video to finally setup klipper on my ender 3 2018 with an SKR mini board. Big thanks for all the work you put into this.

[@julias-shed]

Brilliant managed to convert from Octoprint to Klipper on my Ender 3 plus skr mini e3 v1.2 in just over two hours 😀 just finishing its first print. 😀

[@ZURAD]

I've been having issues with my Ender 3 not moving slowly enough for wire EDM. Wanted to convert it to klipper. This video is perfect! Thanks!

[@CryptolockerMD]

This made me giggle.

[@grindsman22]

Damn that's a complicated process but bravo for explaining it so clearly! I'd like to upgrade my CR10S so that I can use input shaping at some time in the near future.

[@diogorodrigues1571]

Hey did you instaled it in your cr10? how it went?

[@grindsman22]

@@diogorodrigues1571 Yes I did. It was very challenging, if you miss a step or make a mistake at any stage of the process, it won't work and it's best to start again from the start. I had to design a housing for the CB1 Pi, new BTT SKR Mini 3.0 motherboard, plus touch screen, it was so satisfying when I managed to print something,and it's so much quieter. Klipper keeps getting updated and unfortunately after having a working webcam, an update stopped it working. the coding takes a while to understand but you get used to it and the Klipper forum is very helpful.

[@DaniJoker]

Thanks a lot. Best Tutorial ever. I managed to make everything works 100%. Ender 3 + BL Touch + Raspiberry 2 Model B.

[@Vector3DP]

Great to hear!

[@kennethbeal]

Thank you! About to try Klipper on my new Ender 3 V2 Neo, will follow your instructions. I have an 8 GB Pi that I bought a few years ago that I'll dedicate to printing. Thanks again!

[@zuschauer955]

hello, how did it go if I may ask? I am about to try and use Klipper on my V2 Neo as well

[@kennethbeal]

@@zuschauer955 Actually never got around to it; gave that printer to my nephew. Got a Creality KI now, just using it stock, it's going great. Good luck to you!

[@zuschauer955]

@@kennethbeal Thanks for replying :) It was a bit of a headache but I managed to set up Klipper and have yet to configure some bits, but it's going in the right direction :D

[@beazy4real2]

When adding the board alias for the LCD display, you copied the alias from board 4.2.7. not board 4.2.2. When I changed the bltouch pins to match the alias and couldn't get the bltouch to a closed state. I found the LCD display config without the alias and the bltouch sensor worked correctly. Everything else was spot on, thank you for this video. Keep up the good work.

[@sensemumu]

Hey, can you help me with this one ? Did you find a Pin-config for the 4.2.2 ? my display does not want to work :D

[@mindbendernine]

Edit: I hope that you are resting well and that your recovery and recuperation are fantastic. Sending best wishes and positve vibes to you - Get well soon. All the best to you and your family!

[@Vector3DP]

One of the best 3d printer firmwares available. Your loss.

[@mindbendernine]

@@Vector3DP Can I offer a suggestion? Find a way to show the section on editing the cfg file in a more user-friendly way. Your video is daunting and possibly intimidating to any users who are not familiar with Linux (which I work with daily, so this is no big deal). Configuring the firmware isn't the issue, but your process could be streamlined a little better with less back-and-forth editing.

[@ricenoodles376]

You got to be kidding me. I legit just did this 2 days ago and had a hard time figuring it out. Should’ve waited till this video came out.🤦‍♂️

[@Vector3DP]

Haha, sorry about that! 😅 Remember to share it with others that might need it so they don't go through the same struggles you did! 😊

[@grathado28]

At this point everything he's saying seems like common sense I just like this dude😅

[@jeffarcher8827]

Thank you for this guide it definitely helped although the switching between methods/boards did cause some confusion, I would suggest creating a separate guide for mainsail and fluidd with all the boards. Also FYI there are a few errors on this guide for the SKR E3 v2. You cannot upload klipper via usb onto the board, it must be done via SD card and the .bin name must be firmware.bin, not klipper.bin

[@Vector3DP]

Everything I did in this guide I did complete on the boards so it's all possible as shown unless they have updated it and removed that function but that seems unlikely.

[@jeffarcher8827]

@@Vector3DP If you read the documentation at the top of the E3 V2 printer.cfg (18:05) it has it noted and it did not work for me yesterday until i renamed it

[@BenEBrady]

Thanks for the great, very comprehensive video, Adam. Well done and very informative.

[@Carolinawoodturner]

Great tutorial and very thorough. I guess I'm a bit slow but you talked so fast I had to keep replaying the video to understand what you were saying.

[@FredrikNorW]

This was great! One note though is that the early 1.1.3 boars and similar needs to have a bootloader installed before trying to flash Klipper firmware :)

[@allanjones4283]

Matey.. LOVE YA WORK!! Had no idea whatsoever about Klipper until your vid. Cheers big ears 😀

[@MikeloiML]

what am i suposed to do at 17:20 flash the printer? i can´t use that command

[@gregdalton3517]

Nicely Done! 👍 I've got a parts order from BTT arriving Friday...so this comes in handy...great timing!

[@thedankduck0218]

I have the same Ender 3 neo with the 4.2.2 main board, I had an issue with the probe not working and saying “failed to verify sensor state”. How I fix it was instead of using the bed_mesh, safe_z_home, and bltouch sections from the ender 3 s1 config I used those sections from the neo v2 config. Still swapping Probe_in and probe_out .

[@dawidgrela9823]

Thank You, this was very helpful !

[@kenhuffmanjr9919]

FYI, when you suggest to NOT install the macros, this results in the mainsail.cfg file being missing. If you run through the install again in KIAUH then the only prompt is to install the macros. Doing so will add the mainsail.cfg file. I saw some comments below about a missing fluidd.cfg and thought perhaps there was something similar happening on the fluidd side. Hope this helps someone.

[@snerttt]

Thanks, it did..

[@Wbmfishman1]

Man you are awesome. Had to watch this twice just to keep up. Fantastic content. Have an Ender s1 that is sitting idle and going to Order all these components give it a go Thank you.

[@paritycuber2407]

Thanks so much I got Klipper running super quick

[@TruFilmProductions]

I was debating if I want to return my Sonic pad and use my Pi 3 B+. I can do all this but I don't want to. 🤣 The process is more than I thought. Sonic Pad is so much easier.

[@ellafoxoo]

I think a better focus of this video title/intro would definitely have been more on the reliability of Kipper for the Ender 3 series, than on performance printing. Creality's version of Marlin is a mess internally, so flashing anything like stock Marlin or Klipper brings a huge improvement to bug squashing. Nonetheless, a good guide 😃

[@Vector3DP]

That's true of most budget bed singers I think, very buggy modifications. I just think performance is more relatable to more people. Maybe..🤔

[@daliasprints9798]

@@Vector3DP It's not just performance but quality at performance. Unless you're running the stock firmware without input shaping and pressure advance miserably slow, the quality is abysmal. Ringo all over and bulging corners and seams. Klipper lets you get perfect quality at same speed or nearly perfect a ton faster.

[@barbarosbozkurt758]

Which Rasberry Pi would work?@@Vector3DP

[@bargeresman]

ty for the good explenation of all the boords , i brickt my 1.1.3 board ( flasht a bootloader without a arduino ) bad idea when there are almoste only arduino video;s on yt. u have the best explenation on how to install everything, Big Thank U for your knowlage.

[@DonWonwz]

sadly the 4.2.2 ender no longer works. been trying since december 14 - no luck yet. thought i would check here last time before marketplace - video info good here thanks

[@wangyao127]

It absolutely helped me,Thank you so much and appreciate.

[@kingbaaka3D]

Awesome video, i watch like 10 videos before this, i am glade i dint brick my system by now XD, but this video is compleat is what i like. over stop at after installing minstall and tell you to do it yourseld, do what. i was breaking my head for 2 whole days. this help me do it within few hrs. Thank you soooo much.

[@joku900]

If you have problems with Mainsail and Ender where you can get the mcu but the the Mainsail os doesnt connect to printer (printer is not ready the klippy host software is attempting to connect. please retry in a few moments.), try usin command "make clean" when making firmware. I had made typo to config before and only this fixed it

[@BurgerSoda]

what do you mean by when making the firmware? as in flashing it to the raspberry pi?

[@dmytro.d]

Very nice and concise tutorial. A bit window-centric. No wonder, most people use Windows. But I guess Linux users would be able to figure this out by watching this video and adapting tools used.

[@Vector3DP]

If you can use Linux, you can probably do this in your sleep 👍

[@travistucker7317]

If you're running Linux, i guess you could minus the pi, if the computer isn't going anywhere

[@Drumaier]

@@travistucker7317 Is what I did, no Pi stuff, I just installed klipper/moonraker/mainsail in ubuntu and i'm controlling the printer and that machine from my windows pc. I did this just because I had a spare pc so buying a pi didn't make sense in my case.

[@GoTVm_]

I'm having issues installing the firmware to my BTT SKR mini E3 V2.0. The settings change since you recorded the video: - it asks me whether I should make flash or stm32flash, which it doesnt say in yours - board number for the v2 seems to have changed from 21 to 23 - as far as I know and as far as printer.cfg info at the top says, I should put the klipper.bin file on an SD card instead of flashing to the MCU from USB, as that is not possible on this specific board.

[@retrosteve2732]

I'm having the same issues, did you manage to resolve your issues?

[@kafri31]

any update on this? I stuck on the same issue and have info that flashing failed due to "unable to connect to MCU"...

[@gljay]

1.7.5 of the pi imager no longer has 3D printing option. 1.7.4 still does.

[@SmashingBricksAU]

Looks like a good option to get more out of the printer but that is a lot that can be stuffed up in that setup

[@gerardfernandes3332]

In Ubuntu 22.04 there's no link for /dev/serial/by-id/, in this case you should put /dev/ttyUSBx (where X is your USB port), anyway thanks a lot for this wonderful tutorial! I was finally able to use Klipper on my Ender3 v2 using an old laptop that lies full of dust!

[@Nexx8969]

I have M8P with CB1 on a Voron. And I have Duet 2 Wifi on my old Delta anycubic. Duet wifi 2 is 170 bucks .. klipper costed me 102... With more drivers on it and better processors and the wire pins are higher quality. And I have to say, klipper programming is a lot more advanced, and user friendly. Lots of options for you available including using USB cameras, remote control etc .. My duet 2 wifi is up to date, it sometimes still have glitches, it's not as fast on CPU power as klipper... Long story short duet sucks and overpriced. Duet 3 is almost 260 bucks. If you want to tell me klipper boards are expensive then idk what you expecting.. 100 bucks for most expensive klipper board isn't expensive. Especially when it comes with 8 drivers and raspberry pie. Any one looking to upgrade, buy the klipper board you will love it. I actually thinking on trying to upgrade my old printer and see how it runs with it.

[@peterwade1234]

My problem is my ip adress with telstra in AU keeps changing. Even when I've purchased a ip adress from AU it keeps changing every couple of days. Great tutorial 👌 very informative. I'm just letting people know out there the difference between ip adress as this can be a night mare. Set it all up and in a couple of days loose everything.

[@Vector3DP]

These are internal ip addresses, they are under your control, not your isp.

[@RodgerE2472]

FANTASTIC Video!

[@FzRune15]

Hello, I am tryin to install Klipper via Mainsail. I am having issues and am stuck around 17:23. The firmaware we generate goes into an sd card and that card goes to the printer directly or does it go into the raspberry pi's card? I did it and my printer doesnt read anything

[@markusgutendorff2684]

one of the best tutoral i've seen. I do already have klipper installed on a pi, but never got round to actuality use it. I have a Anet a8 plus running with ramps 1.6 and Marlin 2.x. But an 8bit ender3 and anet a8 plus are very similar, so maybe not too much work to alter confiq to work from this tutorial. Is it possible to run klipper in a local network rather wifi ? I work at a Highschool and we a not allowed to use wifi or any remote control. Which is the reason for me abandoning the project.

[@VojaFMX]

Well, i tried installing Mainsail, I tried Fluidd, but whatever i try when i get to the cd ~/Klipper/ i always comes up with a directory not found. Looking for solutions on internet and forums left me even more clueless. Any chance someone has a solution here. I bet it's a simple one. Like when octoprint didn't want to run due to using the wrong power supply.

[@baudeliomeraz1362]

I appreciate the video as I am considering doing this to a bunch of Creality Machines. I will say, I have a hard time following this, and some sort of flow chart outlining the steps and the software used would help. Also, could you give me an opinion on how I would also connect this machine or several machines (running Klipper) to Octofarm on the Same Rasperri Board?

[@raynbow6]

@Vector3DP Ahh, just the video I was looking for. Would you recommend upgrading the board on a Max Neo with an SKR MINI E3 V3 to run Klipper? Or is the V2 good enough?

[@MartinManuellubbe]

Great video best one I have seen so far, any chance you have .cfg for a ender 3 max neo?

[@AlexDoesYouTubes]

ls dev/serial/by-id/* ls: cannot access '/dev/serial/by-id/*': No such file or directory.

[@OckertDuPlessis-e5y]

Absolutely brilliant tutorial. I am having trouble getting everything to download and install properly. Keep getting things like cloning klipper from xxxxxxxx failed and file fetched corrupt. seems like everywhere I turn something is not working and I cannot continue. Please Help!!

[@TomReinke89]

I am having a heck of a time trying to get through this. I don't think my printer is taking the firmware flash? I have tried about 4 different microusb cables of differing brands but Klipper always just fails to get the mcu id. Pulling my hair out over this as I'm crossing the 3 hour mark flashing, pulling SD cards out, searching for cables, etc. Any help would be greatly appreciated. Running a 4.2.7 Ender 3 Pro with a CRTouch. I've got a pi4 with Klipper installed and running from what I think is just fine, but either the printer fails to take the .bin flash that I put on the sd card or Klipper is just failing to see it at all. I've tried all sorts of different configurations in the make menuconfig but nothing works.

[@TomReinke89]

I'm stuck and it's almost 2AM. If I leave the pinouts copied from the Ender 3 S1 so it's ^PC13 and PC14 then I get an error that states that failed to verify the BLTouch probe because it's raised and then says it failed to deploy. However if I use the PROBE_IN and PROBE_OUT I get the BLTouch failed to verify sensor state while the colors go all crazy on the CRTouch.

[@allTheSixes66]

Is it possible for you to make the Klipper ender 3 neo config file that you created in this video available to download?

[@cartmellTV]

My CR Touch sends a !! BLTouch failed to verify sensor state I've been following the steps to a T, and did some research, I came across "pin_up_touch_mode_reports_triggered: False", which starts to home the Z axis. however my cr touch for my neo doesn't trigger and the z axis just bottoms out on the plate and the motor starts going nuts. Any ideas?

[@cartmellTV]

To anyone with this issue, it was changing the pins in the bltouch section, leave it as is from the printer configuration without the aliases, fixed my issue.

[@darrenhenson1711]

When is the ElectriPi scheduled to be released? Even 10 months later, I see it is still in pre-order on your website.

[@Blackwambajehuty]

Hello, I realy need some help. I'm trying to install Klipper on a SKR E3 Turbo but I'm getting always the same error "SD Card Flash Error: Unable to connect to MCU". I tryed the GPIO pin !PA14 and i got an error thtat it couldn't creat the klipper.bin file. Now i'm using the pins: !P3.26, !P3.25, !P1.18, !P1.19, !P2.13" and i'm getting the error of the MCU. Can anyone help me on this pls. Thanks in advance

[@BrunoVera]

nice video! thanks!

[@alleycatjack4562]

Is it a problem using the 64 bit version of mainsail on a 1GB rpi4? Should I be using the 32 bit version?

[@RevolutionV1Gaming]

Great Video, do you happen to have the copiled printer cfg file to share? I also have an Ender 3 neo

[@The-Anathema]

I haven't had a time to peak yet, but I'd assume the ender 3 neo MAX uses the 4.2.2 board, reckon it's still worth a watch anyway.

[@tuckerhauser]

Another great video, is a macro tutorial on your list? Thanks

[@Vector3DP]

Ye, I'd like to do this too. Macros are epic.

[@Dk345personal]

great video. the only problem i have is getting my printer to take the klipper.bin file

[@robberd7devos]

How do you make the printer know it has a different hotend or doesn’t it matter

[@mcvaughan1971]

What happened to ElectiPi ?

[@hectorocampo9475]

how do i access to klipper interface from 8:58 i am usigng a orange pi debian bulseye server dist already install but how could access to th main page of fluin or mainsail nterface

[@noodl3d]

Please could you do a klipper video for the pi5 with ender 3 v3 se

[@Maxxis1992]

I have a Anycubic Kobra Max at work for some prototyping. And I’m thinking of adding Klipper into it. A Raspberry 4 in Germany is about 80-100€. A Creality Sonic Pad with Display and acceleration sensor is 120€. Is it worth to play around with the Raspberry if I can get something already being ready ? Is there anything better with the Raspi solution ?

[@jayp5050]

At around 23:30 his glass bed has a clear film covering it. Can anyone tell me what that is?

[@nebulanspaces]

Hey, I have a Ender 3 Pro, but I can't figure it out for part 4, is there a chance you could help me out, or give me tips?

[@zvizionaero]

Hi, when I do the command "make" it reports that a "klipper.elf.bin" has been created but it doesnt show the next step where I can choose the flashing method. I'm running raspbian in a laptop and have a 1.1.3 board. Thanks.

[@amitelgabsi6552]

Cab you show your voron 2.4 (and what black fillment do u used for the voron) bc i just ordered a voron and i need help to chose colors

[@frits183]

Where in Europe to buy the converter u used and put on the raspberry

[@Vector3DP]

Just from my shop in the UK.

[@michaelwilliam3685]

Can i use this tutorial to upgrade my ender 3 v3 se??

[@ioannisevgeniou9622]

hi i have ender3 with 4.2.2. but not have auto bed, where find settings?

[@diademiemi]

Thanks!

[@alejandroheinrich5538]

I have a question. Can all this be installed on a mini PC? If so, can you use the mainsail option that has everything built in?

[@michaeld954]

I have an old pie. The 1st one will that work

[@johnwoodruff3487]

Configuring with two different packages across three different control boards was confusing.

[@emielpul8433]

for some reason the fluid.cfg has become read only. and i cant get rid of the moonraker error now. any solution for this?

[@RandyA_youtube]

I have an Ender 3 with the 4.2.2 board and I’m using Octoprint on a Raspberry pi now - can I use it with Klipper also? Since I have Octoprint running and using, what instructions can I use to get Klipper up and running? I’m I needing to install Klipper on the RS PI first and then reinstall Octoprint on the same pi and restore a Octoprint backup?

[@TheYayaaa]

Great tutorial! I tried doing the Kiauh + Fluidd method, I followed carefully every step. Once I install Fluidd, I cannot access the web interface using the IP address. I tried different things including rebooting the RPi, restarting fluidd, restarting moonraker. Still a blank page... Any ideas to fix it?

[@VinFurr]

I have the same issue, but it is a matter of reading carefully. my ip is 192.168.10.199, but after installing it told me to open at 192.168.10.199:81 note, the last :81 is important. i suspect you encountered this problem

[@octico]

Where can I buy the electripi? I looked on your website but could not find one

[@EsotericArctos]

Just as a quick note, even 9 months ago when this video was released, the Raspberry Pi Installer will not set raspberry as a default password, you need to sepcify one, and you for security would be advisable not to use raspberry. Apart from that, this is a great video and has helped me to get started :) Just two questions here: What is the best way to setup Klipper to and Octoprint on the same Raspberry Pi? I have a Raspberry Pi 3B+ that should handle it. 2. I currently have been using Octodash to provide a touch interface at the printer with a 7" Raspberry Pi Touch screen. Is there something similar available to interface with Klipper?

[@Vector3DP]

it does set raspberry as the password. Thats exactly what i did in the video and thats the password it used.

[@unicohijogaming]

should I delete the .bin file? connected once to mcu now won't connect device id is correct

[@Razorsedgeartwork]

Well, followed along step by step, and appear to have bricked my ender. Loading the klipper.bin files killed it. It doesn't communicate with the klipper interface "printer is not ready", screen is blank, and won't let me flash the marlin firmware back onto it. I'm guessing the marlin bootloader gets wiped during the install.

[@Vector3DP]

Be sure the file is named and correctly and correct settings are chosen for your printer. I promise it works :)

[@tribar0913]

heplt me so much cause theres no other tutorial for the ender 3 nneo

[@jonnysimps]

i have a BL touch on my ender 3 and how do i add that to the code ??

[@yopi1496]

I have creality 1.1.5 board. is the process same as 1.1.3 board?

[@yopi1496]

found out its the same process

[@dipaksutar123]

I am getting error like "Bl touch failed to verify sensor state" I am using CR touch ender 3 pro. can you provide printer.cfg file?

[@Deadlypen859]

is there a way to get the mainsail image without the pi imager because my pi imager refuses to download but I have gotten other imagers to work so id need to get it elsewhere

[@J_spec6]

Will this work for the s1 Plus?? It seems like I can barely find any info on things for that specific model

[@justmilo8694]

do i have to chnage anything if i have a sprite extruder pro? (ender 3 v2 V4.2.2)

[@vash469]

so when is the ElectriPi suppose to be released

[@markusamz]

Does this tutorial also works for Enders 3 S1 Pro?

[@조기환-k2t]

I have v 1.1.5 board, is This board can install??