How to Upload and install Cisco IOU L2 L3 images on GNS3 || [TAMIL]

[@miho47dwa46]

Pozdrawiam Pana Malinowskiego.

[@jijokannukuzhiyil]

Great Video Thanks....

[@devrajbisht84]

Private VLAN not working on L2 switch. The moment ports are put in host or promoscuous mode they go down and never come up. any lead?

[@vickysandhya2851]

Sir neenga neenga ena screen recorder software use panreenga sir ..for windows 10 ?

[@PGRSpot]

This video was recorded with icecream recorder application..

[@vickysandhya2851]

@@PGRSpot free software ah sir enga poi download pananum sir

[@PGRSpot]

I dint remember the website name.. Free cam or ispring also I will use … Which are free and provides good .. Most of my videos are taken from freecam and ispring only.. Last 3 to 4 videos are taken from ispring

[@vickysandhya2851]

@@PGRSpot Thank you sir ..

[@jalalhaider83]

Thanks ok i got it, now the main problem this IOUL2 is having when you practices the dynamic arp inspection feature on IOU L2, it doesn't execute the command ip arp inspection command, while the eve ng iou l2 supports it how to fix it ? or do you have IOU L2 image which supports it.

[@ajithm1138]

bro ,in asa - site to site vpn la dead peer detectiona cli mode la epdi configure pandrathu ?

[@PGRSpot]

IPSEC Configuration - ASA and Router || LAN-2-LAN VPN || POLICY-BASED-VPN || TAMIL kzbin.info/www/bejne/fKOphop_YruLqac

[@tech_code8]

Anna romba thanks

[@jalalhaider83]

i am surprised to know that i used two iou l2 devices to connected with each other, how come their all interfaces were up ? secondly i connected them over ethernet 0/0 both L2 devices same interfaces and tried to make them trunk, i get error message that An interface whose trunk encapsulation is "Auto" can not be configured to "trunk" mode. how will i practice with it ???

[@PGRSpot]

Execute the below commands: Conf ter Interface eth0/0 Switchport trunk encapsulation dot1q Switchport mode trunk

[@anoopps8264]

Hi bro, I am facing a issue like this it's for fortigate firewall. failed to create statement for insert into apps values(?,?,?,?,?) error is file not a database. Before it is working fine but after this installation of L2 ,L3 switch it's like this. Any solution ?

[@vickysandhya2851]

Eigrp named mode pathi oru vedio podunga sir

[@vickysandhya2851]

Gns3 windows 10 la more battery power comsume panuthu sir ithanaikum ios images mattum thaan use panran ithuku ethana solution iruka sir ? . battery power vegama reduce aaguthu

[@PGRSpot]

I haven't noticed such issues.. But what I can suggest is, - please check the CPU/RAM resources while running gns3. - Always run the IOS routers with Idle PC enabled. This can be done by turning off the router in GNS3 project and then right click on the router, and next select either auto-idle PC or Idle-PC. If you have enabled Idle-PC while adding the IOS images in GNS3 for the first time, this is not needed.

[@vickysandhya2851]

IS-IS protocol pathi vedio podunga bro

[@mohamedaminebejaoui550]

is this stable images, because I downloades images that always bugs and the dhcp didn't work for me in the images so i"m looking for stable IOU images help pls

[@mohmaedhajithmohmaedhajith4782]

Hi.. Bro ungalu therija yarum collaboration eadukurangalanu solunga bro

[@naveenshanmugam6189]

Hi Bro , Im not getting stable iou images , if possible share me pls

[@nithyaananth6076]

Bro gns original software link send me.

[@fairplay8347]

Not working 😔

[@PGRSpot]

what is the issue?

[@fairplay8347]

Showing as no such file or directory

[@fairplay8347]

I did everything as u did

[@fairplay8347]

Exactly Could not start IOU :NO such file or directory /opt/gns3/images/IOU/i86bi-............ 32 bit binary support is not installed

[@PGRSpot]

try execute the below commands one by one in ssh session: sudo dpkg --add-architecture i386 sudo apt-get update sudo apt-get install gns3-iou If still issues, try execute this aswell: dpkg --add-architecture i386 apt-get update apt-get install libc6:i386 libstdc++6:i386 apt-get install libssl1.0.0:i386 ln -s /lib/i386-linux-gnu/libcrypto.so.1.0.0 /lib/i386-linux-gnu/libcrypto.so.4