I suggest using the MT3608 DC-DC Adjustable Boost Module, not the buck boost converter in the video. Thats because the one in the video has a cut off voltage of 3.8V which is not low enough. The MT3608 DC-DC Adjustable Boost Module has a cut off voltage of 2V but don't worry that is what the battery protection board is for.
@PabloPazosGutierrez3 жыл бұрын
I have a boost module like that one and is rated for 1.5amps, which is not enough to handle the whole strip at full bright, it will get hot or dim the lights
@TaylorSoloaiJR3 жыл бұрын
Yes you are correct, it happens to the buck boost converter as well that I used in the video. 2 batteries in series is better or 3 is much better.
@PabloPazosGutierrez3 жыл бұрын
@@TaylorSoloaiJR just tested paint two small strips (50cm each) in parallel, and at 11v the light is bright enough and the boost converter doesn't get hot. Now the issue is the protection board. The one down here doesn't work since it's a charger nos a protection for a load, and needs to be powered to work. I think this would be better with a BMS boats that also does the balancing when charging amber discharging having more than one battery in series.
@RiO-kq6vz3 жыл бұрын
@Taylor Solai I had a question ie I have a 42 IR led lamp requiring 12v 1a power supply. So with the method you used to up the voltage to 12v, can I do the same or should i use 2 18650 batteries each 3.7v for my case? Any help would be appritiated. Thank you
@bladior89802 жыл бұрын
@@RiO-kq6vz with two batteries, you have more capacity. In this case 2000mAh means 1,2h from 100 to 0%.
@TRS_By_PS8 ай бұрын
Huge Thanks to you !! Precisely the video I was looking for, since around 5 years ...
@TaylorSoloaiJR8 ай бұрын
It's good to hear it helped. Thanks for visiting.
@3dgeeks3092 жыл бұрын
Can we use this method with 3.7 volt li-ion lithium battery ?
@TaylorSoloaiJR2 жыл бұрын
Yes
@nimroz093 жыл бұрын
Hi, I've made a project just like your video...I did a lil mods by put a switch between the module and the led, so I can turn it on and off easily... but turn out my battery always dramatically drained when I turn the switch off, so the led doesn't lit up every time I need it,,, then I had to recharge the battery so often.. what is your suggestion? or I missed something on the built process?
@TaylorSoloaiJR3 жыл бұрын
You need to put the switch between the battery and the module, because in your project even though the led is turned off the module still uses power. That's why your batteries are draining.
@nimroz093 жыл бұрын
@@TaylorSoloaiJR uhh.. I see.. so thats why.. many thanks sir..
@vanessacacayan22274 жыл бұрын
hi. can i control the WS2812 LED strip with arduino using your method( video) as external source to power the strips?
@TaylorSoloaiJR4 жыл бұрын
Sorry i know nothing about Arduino, hopefully someone in the comment section can help out.
@vanessacacayan22274 жыл бұрын
Taylor Soloai thank you..no worries ☺️☺️☺️
@aviko95604 ай бұрын
It's late sorry, but answer is no, WS2812 take 5V, although the method is the same.
@driftsamurai292 жыл бұрын
so helpful this brought me so much closer to completing my project thank you!!!
@TaylorSoloaiJR2 жыл бұрын
Glad I could help!
@TaylorSoloaiJR4 жыл бұрын
You guys can just also use the powerbank alone with the buck boost regulator. Just need a USB cable cut off the end and connect the wires correctly to the regulator.
@moe59mak3 жыл бұрын
I included the charger port for a build but now i have something that only switches on when it's plugged into the mains.
@cdmgameplays20492 жыл бұрын
they don’t want you to connect another 5 meter LED strip to this cuz that would require I^2 times the amount of current to apply through out the whole 10 meters length, and that's why
@ivanchan6371 Жыл бұрын
I hope you can help me sir,i want to use 18650 battery to power up 12v 90 watt electrical component for 7 hour daily for my little food truck.can you teach me what to buy?I really appreciate if you can help me,please.Thanks in advance.
@ivanchan6371 Жыл бұрын
Does 36v 100000mah 18650 battery will do the job by adding a 36v dc to 12 v dc ?if it can,how many year approximately,it can use?
@ivanchan6371 Жыл бұрын
I'm also ever planning to buy a 12v 80ah gel battery to so the job but i cant find a good gel charger for it in my country.
@reeshugarg27811 күн бұрын
I arranged the same circuit but my strip light does not work on battery when it is disconnected from main power supply
@reeshugarg27810 күн бұрын
What can i do regarding that
@TaylorSoloaiJR10 күн бұрын
Could be anything, what module and voltage are you using it at?
@reeshugarg2789 күн бұрын
@@TaylorSoloaiJR i am using XL6009 Step up down buck boost converter module at 24 V, strip lights of 12 V
@allister28405 ай бұрын
Can i use 12volts Solar panel to charge the battery?
@TaylorSoloaiJR4 ай бұрын
No, you need a 4.2V battery charger
@dronexfun84694 жыл бұрын
I've been looking for a way to put an led strip on a few quadcopters but it needs to be light and easy since I'm an idiot. I don't even know what components to look for. I'd like to power a 12v strip with a 1s(3.7v) li-po.
@TaylorSoloaiJR4 жыл бұрын
eBay has some smaller "step up voltage regulator' that might work for your project. Smaller than the one in the video, just make sure to check the specifications first before buying.
@bhr9874 жыл бұрын
Thanks for this useful explaination ! Liked n Subscribed ! 👍❤
@TaylorSoloaiJR4 жыл бұрын
Thank you, I appreciate the support.
@Mr69viking4 жыл бұрын
I have several 18650, 2200 mah, 3.7 volt, 35amp high drain batteries from a e-cigarette vape device. My question is can I use a 3 slot battery box which would be close to 12 volts to power the same led strip?
@TaylorSoloaiJR4 жыл бұрын
Yes you can, I tried it before and it works. My only concern is that it will lessen the lifespan of the led strip.
@Mr69viking4 жыл бұрын
I want to wire it with a switch for the inside of my gun safe. Like a refrigerator, door opens, lights come on. Should I use a BMS or a fuse? Will these led strips give enough light to illuminate the inside? Thanks for the info.
@generalawareness1013 жыл бұрын
I am a bit stumped, but I have an 18650 going into a MT3608 to drive it to 12v. Then I take that to an XL4015E1 that I set the max voltage to 3.7v and current of anything to light a 3w led. Works but why am I being limited to about 270ma? I remove the LED and measure the current directly (looks like a direct short to the XL4015E1 and how you adjust it) the current is back to where I set it. Where in the world is the issue? If I have it going from the out terms but going through the led I don't I am stumped as I said.
@LicoSantosphotography Жыл бұрын
Hello budy, how are you? Very good your video, congratulations! I'm trying to connect a Ring light 12v 3.5a, which works connected to electric light, on lithium batteries, any suggestions on how to do it?
@omarbeatbox81592 жыл бұрын
Please help me I use 3 battery the same with you 18650 for the same led with you .. I wanna calculate how many hours will say with me ?
@AmitDhimanTinku-mg8lj Жыл бұрын
How to make 5v Bluetooth amplifire at home
@TaylorSoloaiJR Жыл бұрын
Ok I will try
@ArijitSaha-j8i6 ай бұрын
😅
@kevinmanoj52084 жыл бұрын
Great work. How long does the battery last when the LED is at full brightness?
@TaylorSoloaiJR4 жыл бұрын
I haven't tried it on full brightness for too long because the voltage regulator was getting super hot, but adding another battery in series will be the best option rather than just using one.
@kevinmanoj52084 жыл бұрын
@@TaylorSoloaiJR I see. I'll try that out. Meanwhile can I add a heatsink to reduce the heat from the voltage regulator?
@leslievalmadre50863 жыл бұрын
Great video and very helpful for a project i am working on. Can you advise the brand or more detail on the TP4056 you have used. I am intrigued by its configuration offering terminals for charging the battery and seperate terminals for the power out to the led array. Thanks in advance if you can help.
@TaylorSoloaiJR3 жыл бұрын
I actually learned a lot about this board by studying its datasheet online and also watching other KZbinrs. When you are buying one just make sure its the board with the battery protection. The other version does not.
@1255jakub2 жыл бұрын
Serial connection of 3x 18650 should be enough to?
@TaylorSoloaiJR2 жыл бұрын
Yes you can connect them in series with a BMS to protect them, only problem with this it will exceed 12V so it will lessen the lifespan of your LED strips.
@Sanjay_Sahani83 жыл бұрын
I from India🇮🇳😇
@sledgenft88567 ай бұрын
Current not supplied for a double connection
@rahmatdharmawan1577Ай бұрын
nice tutorial bro 🔥🔥🔥
@TaylorSoloaiJR5 күн бұрын
Thanks 🔥
@nikolagjorgievski89402 жыл бұрын
Taylor Soloai Want to ask u,How much long time will running full 5M strip of leds with 2x 18650 5000mAh in series with this buck booster? Thank u for answer
@TaylorSoloaiJR2 жыл бұрын
As I explained in the video, it depends on how much current is flowing from the batteries to the buck/boost converter. The brighter it gets the less time the LED strips stay ON, but I would not use the buck/boost module because it will automatically shut off when the batteries goes down to 3.7V
@alejandroperdomo9642 Жыл бұрын
Can I connect a 3s Battery 11.7v to the TP4056 charging moudle ?
@TaylorSoloaiJR Жыл бұрын
No, you need a 3S BMS for that.
@Antim8x25 ай бұрын
liked your video, would this also work with a solar pannel wich produces 28W and 5v ?
@TaylorSoloaiJR5 ай бұрын
Sure, you can use that to power the LED strip
@chimangochitwanga4254 Жыл бұрын
Can you also add a switch to turn on and off the LED Strip
@TaylorSoloaiJR Жыл бұрын
Yes you can, make sure it's between the battery and the voltage boost module.
@chimangochitwanga4254 Жыл бұрын
Will work on it. And i have been trying to add a few cells to but it is not working any suggestions on modifications i can make
@TaylorSoloaiJR Жыл бұрын
Adding cells in parallel or series?
@chimangochitwanga4254 Жыл бұрын
@@TaylorSoloaiJR added them in parallel. or which one would you recommend
@TaylorSoloaiJR Жыл бұрын
It's better if you put two of them in series, unless you have three then you don't really need the buck boost converter. Don't forget you're going to need a BMS for the batteries in series.
@supercrash19913 жыл бұрын
Hi friend nice video i have a question i have a lot of 18650 batteries bout i was trying to doing that with 4 aa batteries that was giving 5.04 v bout that not works any idea why sorry for my english 😅
@TaylorSoloaiJR3 жыл бұрын
Were you using the step up step down voltage module that I used in the video?
@MrBobWareham2 жыл бұрын
Voltage drop end to end
@TaylorSoloaiJR2 жыл бұрын
Just don't use it at high voltage
@agusrib2211 Жыл бұрын
if i use a 5000mah power bank for a 5m 5v led strip, how much would it last?
@TaylorSoloaiJR Жыл бұрын
I'm not sure because I never owned one and it also depends on the color of the led strip.
@PabloPazosGutierrez3 жыл бұрын
Can you show how to do the same but with 3 or 4 batteries? I mean with the protection board, I have more batteries but the charging is done in parallel while the discharge should be in series, and I'm not sure how to do the connections.
@TaylorSoloaiJR3 жыл бұрын
Their are BMS boards made for 3 or 4 batteries but that means you also have to buy a charging adapter. I'll try and see if I can make a video on how to do it.
@tahmidenter1036 Жыл бұрын
এটার দাম কতো?
@TaylorSoloaiJR Жыл бұрын
The boost converter cost about $1 USD
@bvdvoort638 Жыл бұрын
Great video. But I could use some help. I had a DC buck converter laying around, but it seem to only be able to step down the voltage. input is 4 volts, output can only go up till about 4.2 volts. what could be the problem here? Do I need a differen buck converter?
@TaylorSoloaiJR Жыл бұрын
Buck converter can only step down voltage, you need a boost converter.
@bvdvoort638 Жыл бұрын
@@TaylorSoloaiJR Thanks! I'm ordering some.
@dakshpatel24094 жыл бұрын
Hii sir what power is required to light a single led from a led strip light which u have shown in this video please help me sir I have a project pending Your videos are very helpful 👍 sir Liked & subscribed
@TaylorSoloaiJR4 жыл бұрын
Sorry I don't have the answer for that now but I will get back to you after I run the test. Also thank you for subscribing.
@randallslaw53913 жыл бұрын
The boost module, you think I could salvage one from one of my old vape box mods that has variable wattage? If so can you make a video showing how?
@matthewstrangwood84632 жыл бұрын
Not possible as they are regulated and timed Boost converter are only about 2 quid
@eraittech94632 жыл бұрын
i want to know a name of cable which you use for connect to power booster and led strip
@TaylorSoloaiJR2 жыл бұрын
Its just speaker cables, nothing special
@jonathaningargiola98243 жыл бұрын
Hi there, interesting video. I'm looking for led strips that I can use to light up some Lego models. I have seen 3V Led strips working with 2 button batteries (CR2032). Apparently it can even work for 2 days in a row (but I doubt it). My question is, can you use a 18650 battery to expend the running time or is the voltage too high for such 3V strips? Can I also add one one these modules to the circuit to recharge the battery? What about putting 2 AAA batteries in series, that way the battery box could be thinner? The goal is to get a very dimmed light, I really don't need a full power bright lighting. It's just for ambiance. So would I need an extra module to also dim the light to a minimum? My current project is for a Lego Millenium Falcon back sub-light engine, measuring 30 cm long and probably adding one Led strip part (they are cuttable every Led - 60 Leds / meter) for the gunner and another one for the cockpit. Thanks
@TaylorSoloaiJR3 жыл бұрын
The module that I used in the video can also lower the voltage, so in your case 3V. The only problem with this step up and down voltage converter is it only works starting at 3.7V, so below that it will shut off. You can run it with only the AAA batteries but you probably need a BMS board to protect the cells from being over discharged but you need to find out how much capacity the batteries have. Honestly for me Ive been using li ion batteries for my projects, you can even get them for free from old laptop batteries. You've probably seen how they salvage them from other KZbin videos.
@catak054 жыл бұрын
hi. if i use Non-rechargeable batteries its necesary the lithiu battery charger module?
@TaylorSoloaiJR4 жыл бұрын
If you use Non-rechargeable batteries you don't need the battery protection board. I suggest you use the MT3608 DC-DC Adjustable Boost Module, because the cut off voltage is 2V. So if its below that it won't work anymore.
@xtinctt27234 жыл бұрын
My led strip came with no remote or power and just 2 cable with opening in the end like yours. Is this the only way of getting power to the led strip
@TaylorSoloaiJR4 жыл бұрын
Yes, those are the cables to deliver power to the LEDs. Do you have the 12V or the 5V LED strip?
@xtinctt27234 жыл бұрын
Taylor Soloai 12v
@DJNITROALLY4 жыл бұрын
u can connect it in series they say that coz u need more amps on ur power supply and u need to add voltage adding wires for voltage drop
@TaylorSoloaiJR4 жыл бұрын
Yes you are right, connecting two in series is better but I just want to demo that you can use lower voltage batteries to power it but with with less than 12 volts.
@DJNITROALLY4 жыл бұрын
@@TaylorSoloaiJR ahh I see but I just came across ur vid now ima try the exact same thing u did but will multiple batteries so it should run about longed
@TaylorSoloaiJR4 жыл бұрын
Do you use salvage 18650s or do you use the new batteries? Just wondering what others use for their projects.
@DJNITROALLY4 жыл бұрын
@@TaylorSoloaiJR I got a few new batteries but I also got some old ones ima try with both
@DJNITROALLY4 жыл бұрын
This is also a good idea to run a modem or wifi router
@eross21 Жыл бұрын
so how long will it power those led batteries for? this is very cool
@TaylorSoloaiJR Жыл бұрын
Depends on what power source your asking about. The 18650 by itself can power it up to 2 hrs.
@Alamini964 жыл бұрын
I have a 144 led 5V strip. Will a single 18650 cell (samsung 25r with 2500mah 20A continous discharge) be able to give out around 10 amps when boosted to 5 volts?
@TaylorSoloaiJR4 жыл бұрын
I don't think that 5V led strip will pull up to 10A, should be lower. You could just use a powerbank. Since it outputs 5V, just need to find out how much mA it pulls. Its a lot easier and less work.
@Alamini964 жыл бұрын
@@TaylorSoloaiJR I'm going by the official listed power ratings by adafruit. They say a 144led 5V strip would consume 43 watts (8.6 amps @5V). Here is the link. Please help me out knowing what sort of portable pworr supply can I do for this :) thanks. learn.adafruit.com/adafruit-neopixel-uberguide/neopixel-strips
@TaylorSoloaiJR4 жыл бұрын
@@Alamini96 the module shown in the video won't work with the lights you have. Because 8.6A will be too high for it and its going to shut off. Unless you try using it at a lower voltage (which means the brightness won't be as strong) and get lower amperage.
@dakshpatel24094 жыл бұрын
Hii sir what power is required to light a single led from a led strip light which u have shown in this video please help me sir I have a project pending Your videos are very helpful 👍 sir Liked & subscribed
@TaylorSoloaiJR4 жыл бұрын
Are you planning to use the one 18650 battery shown in the video to power it? Or different power source?
@dakshpatel24094 жыл бұрын
@@TaylorSoloaiJRyes it is 18650 of 2000mah power bank battery power bank is of ambrane compony,
@TaylorSoloaiJR4 жыл бұрын
@@dakshpatel2409 sorry for replying late but I have no information about how much power a single led in the led strip uses but from my experience the shorter the led strip the less power required.
@dungeonsdoodads43063 жыл бұрын
Would 3 of these batteries work without the board?
@TaylorSoloaiJR3 жыл бұрын
Yes it should be fine, but just check the specifications of the led strip if its okay to use more than 12V since the 3 batteries will give 12.6V when they are fully charged.
@RiO-kq6vz3 жыл бұрын
@Taylor Solai I had a question ie I have a 42 IR led lamp requiring 12v 1a power supply. So with the method you used to up the voltage to 12v, can I do the same or should i use 2 18650 batteries each 3.7v for my case? Any help would be appritiated. Thank you
@TaylorSoloaiJR3 жыл бұрын
Yes, you can use two 18650 batteries. Putting them is series is recommended. Just make sure you have 2S BMS for your batteries to protect them from being over discharged.
@RiO-kq6vz3 жыл бұрын
Do you mean 2 series charge module? BMS? Do you mean this-- XR HX3S 18650 3S 12V 25A BMS Protection PCB Board Lithium Li-ion Battery. I found this on amazon.
@TaylorSoloaiJR3 жыл бұрын
Yes, those modules help with both overcharge and over discharge.
@RiO-kq6vz3 жыл бұрын
Thanks a ton for your help.:)
@RiO-kq6vz3 жыл бұрын
Hey man one last thing, in your case you used a single18650 battery holder and so connected only 1 of those blue units to prevent over discharge. However if i use 2s or 3s batter holders how many would i need to connect and in what manner? Like 3 in series to each other or how?
@fezontheblock4674 жыл бұрын
You have a link for the buck boost regulator you use.?
@TaylorSoloaiJR4 жыл бұрын
Select the option that says "XL6009 Red Module: www.ebay.ph/itm/Automatic-Step-Up-Down-Converter-DC-DC-Buck-Boost-Power-Supply-Replace-XL6009/123965623616?hash=item1cdced4d40:g:Wj0AAOSwYUpdwplX
@fezontheblock4674 жыл бұрын
@@TaylorSoloaiJR thanks, i see that you turn it on with the charger? Is it also possible to do that with a button switch?
@fezontheblock4674 жыл бұрын
@@TaylorSoloaiJR I want to use this module in a clothing rack with a motion sensor. Zo it has to be as small as possible for me with the batteries. this video is perfect
@michaelisaguirre11043 жыл бұрын
Fast low bat
@TaylorSoloaiJR3 жыл бұрын
The higher the amperage the faster it uses the battery capacity, use a 5V led strip instead
@bradw18083 жыл бұрын
Can you connect 3x 18650 in series to give you the 12v and quite abit of mah? What do you have to keep in mind if this is possible?
@TaylorSoloaiJR3 жыл бұрын
3 18650s in series will give you 12.6V which is okay but it might shorten the lifespan of the LED strip but the good thing about the buck boost converter is if you set the voltage to 12V it will stay there OR you can just charge them only up to 12V, just don't forget to use a Battery Management System (BMS) board to protect the batteries from over discharging. So you won't be increasing any mAh from connecting them in series but if you need to increase that then you need 3 extra 18650s. Three pairs of 18650s in series (2P 3S battery pack). I hope that makes sense
@bradw18083 жыл бұрын
@@TaylorSoloaiJR , this helped alot thank you! On Average whats the amp requirement for LED to be on full power? If I know this value (im sure each brand differs) can I just add them up with the amount needed for the task and ensure my battery can handle discharge rate on top of using a Battery monitor circuit?
@TaylorSoloaiJR3 жыл бұрын
I'm not really sure because their are different LED sizes so you would have to do this on your own, just follow the diagram in the video and you should be fine. That's if you already have a multimeter.
@melkileo3 жыл бұрын
Hey, do you think that with such a regulator and multiple batteries in parallel it would be possible to power up a 5m 2812b Led strip at full power without burning everything ? (18w/m) Thanks !
@TaylorSoloaiJR3 жыл бұрын
You need to get one with a heatsink already attached, the one in the video will eventually shut down if it's over heated from the heavy load
@melkileo3 жыл бұрын
@@TaylorSoloaiJRwow, what a quick response 😅 Thanks a lot !