How to Use the ebikes.ca Hub Motor Spoke Calculator

[@BobSmith-zx4jy]

I have to say Justin is a walking E-Encyclopedia! Great videos explained very well. Thank you all for the time you put into making them.

[@joeows6537]

I love watching these videos they make me feel smart. I'm saving up and I'm going to get me a grin someday.

[@mscir]

I got a bike cheap on CL, the owner blew his 2nd motor in 6 yrs and was over it, the Grin motor, controller, PAS, throttle, brakes, display work great and I saved a ton of money. So if you can find a bike like that can have fun building it and save. Grin was great about helping me, a complete newbie, excellent customer service, and the motor has a temp sensor which the controller monitors, and it reduces power before the motor overheats, maybe other motor/controller setups do that, but I didn't see any in my research, so I couldn't be happier with my bike.

[@joeows6537]

@@mscir I purchased the Luna cycle Galaxy paint bike only last May. For 1,400 it was the best bike for the components I could find. I plan on getting the Luna bbshd and the 72 volt battery and then I'll get grins Phase runner and Egg rider and I should be all set. By springtime I'll be enjoying the Hiawatha National Forest in style.

[@eastwood111]

Have used this calculator to build many wheels. Thanks Justin!

[@aayala1053]

Another excellent video, keep up the good work! I've used this several times to build my wheels.

[@mikekearsley2407]

Absolutely fantastic vid. Thanks from Woodinville WA

[@ThomasMcFarland]

Thank you for the hard work of setting this up!

[@marcossantos8015]

Excellent video very explained and is really great

[@nicod974]

Very informative, thank you

[@Themonster81iq]

Great tutorial sir, but I have a question and hope to assist me with .. My e bike rims are 26"x4.0" 84mm wide and the previous spokes Dia for the rear rim was 10G/ 215mm length. Planning to replace the rims with the same previous rim size but with different model and here is my question will I be able to use 12G/215mm spokes instead of the 10G ? Thanks in advance

[@GrinTechnologies]

10g is an almost unheard of size for a bicycle wheel. If your motor flange has holes drilled out for 10 gauge spokes, then there is a good chance you will need washers on the the spoke heads if you use 12 gauge spokes instead.

[@caseycameron437]

I'm still poking around but I'll comment here and see if you have any ideas. I'm trying to convert my Schwinn Tourist Hybrid bike into an e-bike (it's already a great commuter bike!) with a BAFANG 500w rear hub conversion kit. I like the look of the bike as it is, and I'm toying with the idea of keeping the current rear wheel instead of the one that comes with the kit. The rear hub motor with the kit is the BAFANG G020, and I have 700c wheels... and all the spokes are in pairs around the wheel. The hub appears to have evenly spaced holes. Is that going to mess things up terribly? And could you add the specs for the G020 to the calculator? I'm sure it's a common one these days. Thanks for the info, tool, and helpful video!

[@GrinTechnologies]

You're asking if single cross is fine? It's not clear what you mean by "all the spokes are in pairs around the wheel". WIth smaller geared motors like this and a large 700c rim, both single cross and double cross work fine.

[@phase3ute]

My question is can you supply a 10 gauge spoke for a qs273 inside a 19” moto rim. The spokes I have got from previous vendors are of poor quality. I’m after good quality spokes as this needs to hold over 50hp.

[@GrinTechnologies]

Unfortunately no we only do 13 and 14 gauge spokes and only supply parts for bicycle rims, not motorcycle rims. You should contact a motorcycle parts supplier for that.

[@completesalvation1755]

Very nice work, interesting and valuable information since rebuilding a hub motor rim is not the same as rebuilding a standard bike rim. I hope to use the information to change my motor from a standard rim to fit a fat bike tire.

[@GrinTechnologies]

As long as the spoke holes match on rim and motor you're good to swap!... With appropriate spoke length of course ;p

[@benrichards1410]

Duuuude good job, collect 5 cool points

[@Caininthechongs]

I have a 1000w csc rear hub, what would that come under?

[@peddeler2]

my ebike with a bafang G060 fat motor, 20 inch fat wheel, is radial laced with evenly spaced spoke holes (not paired) but with heavy 11 gauge spokes. Not good?

[@GrinTechnologies]

In 20" rims the radial lacing will often hold up OK, but if you find after riding the bike a lot that the spokes gett loose and the nipples needing constant tightening then we'd suggest relacing with a single cross pattern.

[@peddeler2]

@@GrinTechnologies okay thanks, I'll check them often.

[@FlyWithSergio]

Hello! Could you tell me a nice motor for pull 30-40kg continuously during 5 min at speed of 25km/h? It's for a proyect. Thanks so much!

[@GrinTechnologies]

What is the diameter of wheel? The smaller you can have for the wheel size the easier it will be to have this pulled off by a hub motor. The RH212 with statorade in a 20" wheel size is getting close: ebikes.ca/tools/simulator.html?blue=Lbs&motor=9C212_7.5T_SA&cont=cust_50_100_0.01_V&grade=15.5&hp=0&wheel=20i&mass=150&batt=B5220_GA But normally we'd be suggesting running 2 motors for this kind of thrust level.

[@geraldshields9035]

And this is why I love mid drives!😂

[@bibork]

muy buena aplicacion exelente gracias

[@johnbird8605]

Hi guys, great videos by the way! Would the details be the same for motorcycle wheels? I'd like to reverse engineer some Borrani rims and design some wheels hubs? Cheers for your help!!

[@GrinTechnologies]

Thanks John! You might be able to get an accurate read out on the spoke calculator. Not sure if there's a better tool out there for the job.

[@모빌란트]

I want to try it sometime.

[@gamePSeBikeEnduro]

hello 🖖 tell me the front hub or hub can be measured with this calculator? hub + moto rim 1.60-19’’

[@GrinTechnologies]

It can calculate both front or rear indeed.

[@JeepeeConception]

Excellent tool but... I have a front hub with the right flange with a different diameter than the left flange. It would be a nice update to take in consideration this other parameter ;)

[@GrinTechnologies]

We've got one of those hubs in our shop too (this one here www.aikema.com.cn/en/product/product-45-361.html). Is that the same model you have? It's quite doable as a future update but at least in the meantime it's easy to just run the calculation twice.

[@JeepeeConception]

@@GrinTechnologies yes it is Aikema hub ;)

[@jasonbrand5762]

Where can i order a trike axle ?

[@GrinTechnologies]

Unfortunately not from our spoke calculator

[@hdtv4075]

Bafang G062 motor to use with kenda fat 20"x4.0 wheel (RearWheel )

[@Elpatronbikes448]

where to buy a good machine for making spokes

[@GrinTechnologies]

We are extremely happy with the japanese Morizumi spoke machine that we currently use www.wheelfanatyk.com/store/morizumi-sct-machine/

[@Elpatronbikes448]

@@GrinTechnologies 😉

[@Elpatronbikes448]

@@GrinTechnologies kzbin.info/www/bejne/hoXWY516p5tribc&ab_channel=andrejmihalik😉

[@Bikepacking]

Good info