How To Winterize An Inboard Engine

Рет қаралды 83,755

Күн бұрын

Discount Inboard Marine wants to show you how to winterize your inboard! Here are the steps:
Be sure your gas tank is full to keep out condensation and that it has stabilizer in it to keep your fuel fresh. Change the fuel filter.
Change engine and transmission fluids.
Run engine long enough so stabilizer goes through entire fuel system. Next Fog cylinders with spray fogging oil.
Spray into carburetor or throttle body while engine is running (each cylinder if multi port injection).
Remove all engine and exhaust manifold drain plugs.
Consult manufacturer or dealer for catalyst exhaust system winterization procedures. Then, Loosen your alternator belt and raw water pump belt so they are in a relaxed position.
Remove your impeller from the raw water pump and keep it in a seal tight bag.
After all of that, rotate your steering wheel from lock-to-lock position two or three times a month to keep cable lubricated and help eliminate condensation problems.
Disconnect and store your battery according to manufacturer's instructions. Call the skidim team at 803-345-0996 with any questions!
Click here for all of your winterizing needs!
skidim.com/maintenance/winter...

Пікірлер: 30

@barrysoklofske4221 8 ай бұрын

Have the same engine since 1998. GT40 version. I drain water as shown plus the trans cooler which he didn't even mention. I have never added antifreeze and our winters in Canada see 40 below.

@hhiibbaalleerr Жыл бұрын

SKIDIM - best run business ever :) Great folks!

@mcleodhomeservices 4 жыл бұрын

Very helpful! Thanks Vince!

@peterkazaks 2 жыл бұрын

I haven't been draining the water before putting in antifreeze, but will try that this year. I pull the thermostat before running the antifreeze in and fogging, so that I know for sure that it's flowing.

@Fast351 2 жыл бұрын

Yeah make sure you do. RV antifreeze is not designed to be mixed. If you're not in a real cold area you're probably OK but here in MN it gets down to -30 some nights, you want to make sure that stuff is 100%, not diluted.

@Sandy-zj5fl Жыл бұрын

Did he not have antifreeze in the motor? What did he drain out? My boat already has antifreeze in it.

@Fast351 2 жыл бұрын

Good video. Only thing I would add is that on top of draining the engine, make sure your trans cooler is drained! Instead of removing the hose from the engine side of the trans cooler, I disconnect the lake side from the cooler and drain. Then I hook a hunk of hose to the trans cooler and suck the antifreeze in that way. Don't forget the strainer bowl too.

@Nacwing 4 жыл бұрын

More videos! Good stuff.

@mattyice3549 2 жыл бұрын

SKIDIM is the best!!

@richardgriffith1241 Жыл бұрын

Great video Vince

@Warthog333 2 жыл бұрын

I have the same engine, but it’s fuel-injected. Being in NC my dealer told me fogging is unnecessary (not cold enuf). Also, I pour out the water in the water filter. You didn’t show that. RE the plugs, I grease the threads before reinstalling.

@briancampbell5272 2 жыл бұрын

89 MC Prostar 190, Indmar 351. I have never used antifreeze, just drain the manifolds and the block and hoses. (And much more.) As far as the junk that collects in the rear of the manifolds, I have a 2-3 inch strong rod magnet, so I just stick that in the hole and get the rusty gunk out, been doing it for nearly 20 years, and the quantity of gunk decreases to nearly nothing every year. I think I am going by the book, maybe the antifreeze helps prevent rust.

@winkiiiie 2 жыл бұрын

Antifreeze absolutely helps with rust

@robertrambone9633 Жыл бұрын

What state do you live in? How cold is your winter? I’m in RI and don’t Have antifreeze in right now but drained it.

@tthams73 2 жыл бұрын

Really great video. However, if the motor isn’t warmed up. The thermostat won’t be open inhibiting the antifreeze from passing through the cooling system.

@braddoesitall 7 ай бұрын

Most modern engines have a bypass on the thermostat so you don't need to warm up your engine to fill up the block with antifreeze. It's easy to check this is after running antifreeze through the engine. Locate the large hose going from the engine's water pump (not the raw water pump) to the thermostat housing. Disconnect the end going to the thermostat housing then insert the right size PVC pipe into the hose to get the level higher than the thermostat outlet. Pour in antifreeze to the pipe and most of the time you will immediately start to see antifreeze come out of the thermostat housing and this means the thermostat has a bypass and there is no need to warm up your engine. Check out this video starting at the 7:40 mark: kzbin.info/www/bejne/g3W6nZKgmq2MntU

@keviniwu 3 жыл бұрын

Thanks Vince! Very helpful. Question, how does the rv antifreeze get into the engine if the thermostat is closed (assuming you don't get it warm enough to open the thermostat)? Or are you not intending it to get into the engine?

@job62262 3 жыл бұрын

Exactly what I was thinking. He did not mention to make sure you get the engine up to temp to open the thermostat. Unless the engine gets up to temperature and the thermostat doesn't open the antifreeze will not get into the entire engine.

@gibsonn14 3 жыл бұрын

@@job62262 Draining the block should drain about all the water on the other side of the thermostat so really its not a big deal whether its open or closed. Also if it's a closed cooling engine then the only thing going through the thermostat is coolant

@krisnowak4 2 жыл бұрын

The water does not go into the engine thru the thermastat. The thermastat prevents cold water from leaving the engine, the raw water pump will directly fill the engine till it's full, then pump excess antifreeze out the exhaust. As the engine heats up, the thermastat will open a slight amount and let some hot water out, which is replaced with cold water from the raw pump. Running a boat wide open across a lake does not fully open your thermastat.

@barefootrocker Жыл бұрын

@@krisnowak4 can you describe the path of the raw water from the lake into the engine block with the thermostat closed?

@brett7562 3 жыл бұрын

My motor is throttle body injected, where do I apply my fogging oil? I have a master craft sport star 19 with a 305 motor.

@skidim8143 3 жыл бұрын

You can do it the same way. Since its multi-port you should NOT spray it through the air intake.

@brett7562 3 жыл бұрын

So fog each cylinder separately?

@skidim8143 3 жыл бұрын

@@brett7562 Yes fog each one individually through the spark plug hole, once the fluid is in the 8 cylinders you turn the engine over once and put the plugs back in.