How to Wire a 48v 2000w Vevor Kit - JordyBuilds

CHECK OUT MY NEW FACEBOOK PAGE TO STAY UP TO DATE -
www.facebook.c...
My builds will be posted there consistently. You will also be able to ask me questions directly. More coming soon on my plug and play kits!
Hey guys, today I go over how I wire my 2000w Vevor kit. Also same set up for the 1800w kits. If you have any questions feel free to ask!
My builds will be posted there consistently as well as ask me questions directly. Also stay up to date on my plug and play kits that are coming soon!
Vevor Kit : shorturl.at/bozV7
Small Pin connectors : a.co/d/gPqdhX9
Anti-Spark XT90 coonectors : a.co/d/7CTkEzm
MR60 connectors ( only use up to 40amp) : shorturl.at/irvLT

[@hyp3rbowI]

thank you so much for this video as my motor was not working and i was worried about why it wasnt then i watched this video and saw that i had a very similar throttle as you and because of you saying you need to use a paper clip to jump the power lock i made a cable with 2 pins on the end that would do the same thing then the motor worked i am so grateful thank you very much.

[@JordyBuilds]

I’m glad it helped !!

[@ebRyder]

Great video my dude...

[@JordyBuilds]

Thanks a ton!

[@desertrider325]

You should do a separate video on how to properly add Flux and temps, your setup etc. for soldering those connection. Would be cool if that was in here.

[@beauparent8718]

What is that three pin connector called for the phase wires? I can find the two pin XT 90 but not the three pin

[@JordyBuilds]

Mr60 I think

[@desertrider325]

What display is that. Link if possible? Looks bad ass having percentage and Voltage! Game changer! Power has heat shrink added but you skipped how or what you used to properly and safely tap into it. Can you elaborate? Did you cut the XT 90 you wired in and than add the wires with just heat shrink?

[@JordyBuilds]

I had the wires soldered to the power wires for my gauge. There’s other ways to do it though. a.aliexpress.com/_msbxcn2

[@AdrianZuniga-vb8zk]

is all the re wiring is it necessary? Not tryna be rude but i just had a question becuase im starting a build and im new and im wondering can this just be like a Plug n play? or is some re wiring like required to actually run?

[@JordyBuilds]

Depends which kit you bought etc. you should be able to make it work how it comes

[@MaddConnekRecordz]

Terrible explanation need to describe it all in detail for us newbies who have no idea wtf you just said. Where’s the blue wire go?

[@JordyBuilds]

Go watch another video then 😆

[@Manfr_]

when you put this on a bike can i just get a 72v battery that doesnt need to be connected to a outlet. a

[@JordyBuilds]

I’m not sure what you mean but no this is the 48v vevor kit. I’d recommend just getting a kunray my1020+ then a fardriver controller

[@kittygrey2181]

Can. Yo u tel me where to find the 3speed button to buy it?

[@JordyBuilds]

Amazon!

[@chrisblair3081]

3 speed seems like a well worth it upgrade

[@JordyBuilds]

I definitely agree!

[@BrandonJones-co4ce]

Do you have a recommendation for a brand lithium battery, ive built a ton of powerwheels but my first razor im building and new to the cintroller and lithium scene, will any 48v 15ish ah lithium battery be ok

[@JordyBuilds]

Amorge! Join modified razors on facebook and look up amorge. You’ll find a guy by the name of allen and there instructions on how to order

[@plane-nerd61]

is it a good motor to buy?

[@JordyBuilds]

It’s a decent beginner kit if you know how to DIY and solder

[@beemerkon]

Are you really doing solder vids do you even know what flux capacitor is

[@JordyBuilds]

lol

[@Jsosodke]

How do you make the 3 speed wires go in order ? Instead of 132 make it go 123

[@JordyBuilds]

Honestly haven’t figured it out

[@farrahlyn]

I just want to know the best way to put a gear on left side so I'm no spinning the crank

[@JordyBuilds]

Not sure what you mean. Flip the wheel and weld freewheel

[@rod8652]

seen you on tiktok and i’m building a 48v 2000w mx350. when i checked my hall sensors i saw one missing wire and i was wondering if there’s one missing as well for you?

[@JordyBuilds]

I’ll double check today!

[@rod8652]

@@JordyBuilds it’s okay man i figured it out. however i am struggling on wiring this caomm battery

[@JordyBuilds]

What’s the struggle ?

[@rod8652]

@@JordyBuilds so for the vevor it has the positive and negative wires like the motor phase wires (they have holes) but my coamms battery has a connecter

[@JordyBuilds]

The plug is called a Dean connector, you can cut ring terminals and put the opposite Dean connector on to match battery

[@JordanDenn]

Do you know what wires you would switch to change the direction of the motor

[@JordyBuilds]

Swap two of the phase wires until it goes correct direction. Two of the three motor wires the blue green yellow

[@JordanDenn]

@@JordyBuildsok I swapped the blue and green wires and it goes the correct direction but under load it jerks at take off and won’t go unless have rolling start

[@JordyBuilds]

@user-yp6nl9sh5b swap a different two

[@JordanDenn]

@@JordyBuildsI think I tried every combination but it’s still jerkin

[@JordyBuilds]

@user-yp6nl9sh5b make sure there’s no reverse that’s automatically enabled or something I’m not too sure

[@mrkeopele]

i've got that same controller, I hooked it up to a hall sensor motor and battery lock out and throttle, i was getting a throttle output signal but my motor was not turning! is there any other jumpers necessary to turn this controller on? or maybe is my controller bad? or my motor bad

[@JordyBuilds]

Do you have your electric lock/ key switch set up ?

[@mrkeopele]

@@JordyBuilds I put a jumper wire across it, I was getting throttle output above 4 volts. I'm dealing with a 2014 Bionx 500w 36v motor that I have to remove all the spokes to get it apart to check inside.

[@ertynh6004]

My moter feels like the e brake is on what shuold i do

[@JordyBuilds]

What’s your set up? Also make sure your chain isn’t too tight and also make sure your brakes are actually not sticking.

[@ertynh6004]

@JordyBuilds no it's my moter and it won't turn on either

[@ertynh6004]

@JordyBuilds and when I turn the motor it feels like regen is on

[@JordyBuilds]

@@ertynh6004 hang turning motor won’t be super smooth

[@desertrider325]

How did you come off the battery for power? Need details on that.

[@JordyBuilds]

Anti spark xt90!

[@billyhendrix]

How long of ride times do you get out of that battery setup?

[@JordyBuilds]

12-14 miles

[@DemseyDee]

what batteries do you have and how long do they last?

[@JordyBuilds]

48v 15ah about 15 miles

[@Jyoosh_]

Do you have a link to that fuse ?

[@JordyBuilds]

Just a standard 12awg 30a fuse

[@kids832]

how do you charge the battery?

[@JordyBuilds]

Plug my charger into the battery

[@kids832]

@@JordyBuilds I didn’t see a charging port

[@JordyBuilds]

@@kids832 what battery do you have

[@kids832]

@@JordyBuilds I’m building my own. But I didn’t see a charging port on yours.

[@ashkonrafie5675]

can you send the link to the throttle?

[@JordyBuilds]

Just electric twist throttle on amazon or ebay

[@UpNorthProductions]

Awesome!

[@JordyBuilds]

Thanks!

[@salfred1027]

When I plug the motor into the battery and roll the throttle the motor will do like 4 rotations then it stops

[@salfred1027]

I still have power going through the controller and after the 4 rotations the gear inches forward then goes back to stationary do you know what the problem could be?

[@salfred1027]

Do you know what the problem could be?

[@JordyBuilds]

Check your phase wires Try swapping two

[@salfred1027]

@@JordyBuilds is that the electric lock wires?

[@JordyBuilds]

@@salfred1027 nope it’s the phase wires

[@AndySlug]

May i ask what fuse u used? 30A?

[@JordyBuilds]

30 or 35!

[@AndySlug]

@@JordyBuildsdamn, thanks for such a quick response mate

[@MaddConnekRecordz]

You go by through this so fast because you know it some people here are trying to figure it out for the first time explain the colors you covered the colors up and didn’t explain them. What’s the blue wire go to the thick one you got red, black and blue. What’s the blue one? You don’t show where that goesand you don’t mention it so far that I noticed

[@JordyBuilds]

I go over it. Blue green yellow is phase wires Red and black or power

[@MaddConnekRecordz]

Which is the high speed switch it’s all Chinese

[@desertrider325]

Bro! Clean work bench and clarity! Top level KZbinr man. I already built these and XT90. But wish I had this video first! Would of saved me so much trouble. Cheers.

[@JordyBuilds]

I appreciate this comment so much. Thank you truly. Working on a more professional set up. Wanting to get a better work bench and a custom banner for the background! Also will have a Shopify with some custom parts posted soon!