How to wire a AT-1 Vfd for external potentiometer and external forward/reverse/stop

This i the simple explanation on how to wire the cheap Chinese VFD AT1 (single phase to 3-phase) so that it can be controller externally with a 10K potentiometer and a double pole double throw switch.
Hope this helps

[@raymonddahlberg]

how can I adjust the torque of the motor at low frequency? I tried with parameter P70 but only get an ugly sound in the engine. I just can't understand what is written in the manual about this particular topic. I have the same inverter as you

[@AmIAntiAntianti]

Perfect thank you

[@andrewhuf6939]

Hi Peter, for the forward and reverse did you need to do any programming, or did it function with factory settings?

[@brilloestelar1]

Hi Peter. Thanks for your video. I own a bench lathe (motor: three-phase, 1.1kw and 140rpm) and a VFD like yours. I would like to install a brake resistor, but I don't know if in this VFD I can install a brake resistor and what is the proper value. Please, could you help me. Thanks again and sorry, my English is not good.

[@user-xx2wk6jp5d]

Hi can you please help i have a cross cut saw and need to put in a two way switch so that i can have it running continuously or on the hand button stop&start also i need to put in an emergency stop

[@thefraperman]

Final i found that i had to set program P06 to 100Hz in order to cover 0-1500r/min using external potentiometer 10κΩ! At first i set 50Hz and with panel potent iometer i could change 0-1500 r/min but with an external potentiometer i changed 0-750r/min. So i set 100Hz to P06 it works 0-1500 r/min with external potentiometer 10 kΩ but when i change P10 to the panel potentiometer it works 0-3000 r/min

[@petergdk]

Great man. Glad you made it work 🙂

[@runbou3485]

Thankអរគុណ

[@renzjacob7380]

What parameter did you change to make that sir

[@beeman1246]

@3:10 P10 set 2 P11 set 2

[@thefraperman]

I want to use external analog signal for frequency and I used external potentiometer 10 kΩ but this external potentiometer start from 0 r/min until 760 r/min to the max position. My single phase motor works max 1500 r/min. Does anybody know what is wrong

[@petergdk]

Try a 3K potentiometer instead. Also - single phase motor for VFD is always a little bit hit or miss. Better to just get a 3-phase.

[@thefraperman]

​@@petergdk Thanks for your answer i'll try with 3kΩ

[@GeorgeEI7KO]

@@thefraperman use a 20k pot and instead of giving the pot 5v use the 12v terminal. 0 to 100Hz on the remote pot.

[@beeman1246]

@thefraperman 1 year ago

[@luissantos359]

Hola podrias ayudarme a resetear de fabrica mi inversor. Al seleccionar RUN me aparece ERR 1. TE AGRADEZCO

[@petergdk]

I only speak english, german and danish.

[@ACWindings]

Good video, but it only applies to the old AT1 models. This is no longer possible regardless of which supplier you bought it from. I bought from Banggood and Vevor. It's all the same crap. With the new models, when you set the parameters P10 to 2 and P11 to 2, you cannot achieve the set frequency (parameter P06) with the external potentiometer; you can only reach about half of the desired frequency. The operating instructions remain the same. So, you need to be careful about what you buy. Don't waste your money.