How to wire ITC-1000 (Farenheit STC-1000 temp controller) for Incubator , Aquarium, Beer brewing

Attention:
Compressor Delay (PT)
Under refrigeration mode, after power on, if the PV≥ TS+DS, the equipment won’t start refrigeration immediately, but waiting for a delay time.
1.When the time interval between two refrigeration operation is larger than preset delay, the equipment will start refrigeration immediately;
2.when the time interval between two refrigeration is less than preset delay, the equipment won’t start refrigeration until preset delay is satisfied.
Delay time will be calculated right after the moment refrigeration stops.
If you need this temperature controller ,You can search"Inkbird" and find it on our Amazon,eBay or Aliexpress store.
Aliexpress Store :www.aliexpress....

[@dlcchannel8881]

Thank you mate. I finally get it right now! I was trying to wire adding with bridges and making the whole thing as clean as possible but I don't know why wasn't working.. Now isn't tidy how I want it but f..... Work so, bravo!

[@markm.9590]

No SOUND! it would b more helpful to Hear whats going on.

[@INKBIRD-official]

Thanks for your advice, we will make improvement.

[@DuilioBiccari]

Wow. Incredible. I understand...nothing. Really nothing. There is a mix of cable with varius colors. Hands over wiring. No words to explane. I thing only an engineer can understand these instructions.

[@Vampire745]

to be fair it`s one of the best wiring example for this model

[@kanookkanook2723]

@@Vampire745 Agreed, I mean, just copy paste what he's doing...

[@kelvinreid9606]

This is pro!! Thanks so much. The manual that comes with this sure didn't help me at all.

[@bitterman159]

Pretty good video, thanks. The procedure can be easily followed by anyone with basic understanding of electricity.

[@comatosed911]

Sound is needed

[@INKBIRD-official]

Dear Comatosed911, Thank you very much for your comment and your interest in our INKBIRD ITC-1000. If you need any support and/or have any question/issue, please do come to us at anytime and we are here to help, while we may reply you a little late because of the jet lag, sorry and please offer your understanding and forgiveness. If you need any support/help from us, you can place your comment here or please send an e-mail with your need to [e-mail] directly and our professional team will get back to you ASAP, please kindly notice this. Thank you again and good luck to us all.

[@sorenrasmussen8676]

Brilliant. It solved my problem 👍

[@INKBIRD-official]

Thank you for your support to inkbird~

[@gpellegrini59]

A simple question. Is it possible to connect only the heating heating device? I want that the temperature doesn't go under 18 degrees (C°)

[@LightTapStomp]

Did you ever find out?

[@ronareister5388]

I have a new Magic Chef Freezer. After removing the OEM temperature control, I have four (4) wires... Black, Brown, Blue and Green. Understand Black is hot, Brown is hot, Blue is Neutral and Green is Ground. Any suggestions regarding the best way to wire the ITC 1000 considering the Black and Brown wires?

[@jailsonlopes8043]

I have a device INK BIRD ITC 1000 220V, sorry I can not program it I need help, thank you very much

[@brodtstuff]

This is not at all good, in the US the wire colors are not used as shown. There is no indication of what is actually a positive unless you really know what you are looking for buy following the plug alignment, this is downright dangerous and inconsiderate for any novice. The video could be done much better and a lot more simple, it needs to be redone.

[@Bruhop60]

Brown = Black Blue = White Yellow = Green. Black = Hot White = Neutral Green = Ground Now it is U.S. wiring colors. Simple

[@MrFrogmasterG]

no mic makes this less than useless.

[@steveeparsonsjr7929]

No audio to know whatever it is your doing I have to give a thumbs down.

[@lakisbouz]

If you need audio to work out whats going on in this demonstration, then you shouldn't be here. go knit a dress.