HP color laserjet Pro MFP M277dw 59.C0 error (part1) check the links in the description may help you

[@lynnlin6013]

Thanks for your video. After following your procedure many times, I cannot close the front door correctly. So I take off ITB first, than install gear module, after check the gear function and front door smoothly, installing ITB back. It works. Just share the experience, thanks this video again.

[@tiknik]

my pleasure have a nice day 🙋‍♂️...

[@niloyu105]

12sec. Ads completed keep watching and support from Al Khafji Saudi Arabia 👍

[@tiknik]

🙂

[@victorng2996]

thank you!, too difficult to fully open the drive unit, so i slit in papers between the lever and the solenoid with the small slit available. printer is working normally now

[@victorng2996]

need to reopen... now paper jammed

[@abubakarrjalloh7647]

Please I just did same to amend the solinoid but difficult to assemble please do a video on how to do complete assemble

[@tiknik]

hello, kzbin.info/www/bejne/m2Wahmajeaiarqs

[@almunawarah824]

Can i just spray contact cleaner without open the internal and wire..just open the hard case

[@tiknik]

hello, you mean you will spray the solenoid? i don't think it's possible because that solenoid is not visible..you need a little effort to open it 🙂...thanks.

[@darielvaleroxas2180]

ang lupit mo talaga.lodi Mc❤

[@tiknik]

😂 pampalipas oras....

[@absoluteeventsandentertain3692]

I have an HP LaserJet 500 m551 printer, and I have the error code 59.00.CO as well, It is hard to reach as a non-professional, I was just trying by watching these videos and following instructions which I did base on the nearest model printer that matches mine, I can't take it out based on the location, I was watching a video until he stops there and use a method and took out the entire bracket that holds the gears and solenoid, so I didn't see the last part how he did it, so I came up with my own method to get rid of the sticky padded piece, " but It wasn't sticking at all, but I use a long needle to scrapped it off, it moves free, been doing so before i assume it was sticking, base on the test i gave it to check if it was really sticking, I close back up the machine which was the hardest part, as I couldn't remember the step I took, I put in the screws in the holes that I saw empty and so far, it holds together, yet I still have about 6 screws leave back, After I manage to do so, I turn on the printer to now see fuser error, but it hardly comes back, but the error code 59.00.CO returns, yet my solenoid has nothing to stick on to cause a delay...what can I now do to solve this issue.

[@JimmyGOliver]

Very helpful video my friend, thank you for sharing!!

[@tiknik]

My pleasure 🙂

[@BMOffice-r5l]

i did, but mow i have another error, 57.03, do you know what can be ? tnaks my friend...

[@komlahtsikata8927]

Hi so after fixing the solenoid and putting the printer together it’s printing blank, can you help?

[@tiknik]

hello, check you laser unit flex cable connectors or the shutter of your laser unit maybe it's close...🙂

[@joannetam5897]

Hi My printer Hp Pro MFP M277dw has the same error 59.0 Can come on site to repair for me? Thanks Joanne

[@tiknik]

oh, I'm sorry. I'm in the Middle East...

[@joannetam5897]

Oh thank you so much

[@louielim8329]

M880 59.00.C0 error can you help me with this error?

[@tiknik]

sometimes this error comes from your toner cartridges...if you have spare toner try it...thanks

[@louielim8329]

Any other problem?

[@pichaytriajeanarizala7571]

what is the name of that spare part

[@tiknik]

hello,part number:RM2-7413 name of sp:main drive solenoid

[@niloyu105]

Sir may eStudio 5018A model. Yung A3 nagbi blink lang pero naka highlight... Kahit ano press sa start copy wala response. Kumpleto naman papel sa loob tray. Salamat 🙏

[@tiknik]

di po yan umaangat tray ninyo...

[@apenasmax7868]

Thank you very much!

[@tiknik]

my pleasure 🙂...

[@fauzifauzan5312]

Setelah saya melihat video ini masalah awal di selenoid saya pasang kemabali tapi ada bunyi suara apa penyebab nya ya

[@tiknik]

hello, try this out maybe this is the reason kzbin.info-L4gmdAm_Bs?feature=share

[@fauzifauzan5312]

Buat hp laserjet mfp m181fw

[@fauzifauzan5312]

Saya rasa saya pasang dengan benar awal nyala bunyi halus tapi pas grounding kaya gear fuser tidak main tidak ikut muter

[@tiknik]

​@Fauzi Fauzan if we recieve in our shop i will make a video for but for now we don't have it..

[@tiknik]

​@Fauzi Fauzan ah ok, therefore something was loose...

[@健金-j8z]

Helpful... And stupid cause, this should not happen to hp

[@eduardoaragona4262]

Good day Sir! Itatanong ko lang sana kung saan nakalagay ang spring na natanggal. Pwede po ba magpa-service sa pagpaayos ng ganitong printer? Baka po magkasundo tayo sa service fee mo po.

[@tiknik]

nasa middle east po ako, try nyo po muna check yung mga cartridge ninyo minsan stuck up din po iyan salamat po

[@tiknik]

check nyo po ito kung ito yung tinutukoy ninyong spring. kzbin.info/www/bejne/m2Wahmajeaiarqs

[@preciousoleke7475]

I encountered this error today..... Losed the gear drive mechanism and all the gears scattered....I'll try and fix it tomorrow and see

[@tiknik]

hello, i suggest you check the part 2 of this video there is important details there regarding the drive mechanism. thanks and have a good one 🙂...

[@Chaundb]

Where is part 2 of this. I. Having similar issue with mine...and i tried about 10 times to get it back in but same result. I have taken a big break from this.....its frustrating.

[@tiknik]

@@Chaundb kzbin.info/www/bejne/m2Wahmajeaiarqs

[@tiknik]

hello, I hope everything will be fine now...🙂

[@Chaundb]

@@tiknik will let you know on Monday when i check it again. I did most of what you did state in this second part. Got everything well closed and lined up. But still get grinding noise and the error 59.C0 error on start up. I'm suspecting I need to line up that solenoid in a specific way with the gear(s) immediately next to it.

[@joannetam5897]

Are you in Singapore?

[@tiknik]

I'm in the Middle East 🙂

[@blessedman2083]

Very helpful.... please the part 2

[@tiknik]

hello

[@tiknik]

kzbin.info/www/bejne/m2Wahmajeaiarqs

[@IAMSPARDA07]

Muy buen video, me ayudo mucho resolvi el problema del solenoide, pero ahora tengo el problema 50.3 y la hoja cuando quiero copian no entra al fusor y se atasca, sabes como resolver eso amigo?

[@Goga_on_ge_Gora]

спасибо

[@tiknik]

anytime 🙂...

[@eduardoaragona4262]

Good day Sir! Pwede pong makuha contact number nyo? Ipapagawa ko kasi ang printer ko, the same model po nito.

[@diemidio]

Hello friend, it is very difficult to assemble this part, it has a more detailed step by step.

[@tiknik]

yes it is, just keep going sir 😉...

[@diemidio]

​@@tiknik Hello friend, to which email can I send you a video of my printer failure?