HP Proliant DL360 Gen8 upgrade for use as a home server with 4K video card, NVMe drives and 10G LAN

Рет қаралды 10,503

Күн бұрын

Пікірлер: 32

@darthkielbasa 10 ай бұрын

Super cool and perfect timing. I just picked up a dl360 gen8 at an auction. Notes on the item said it was never in production and was a cold spare. My other servers are repurposed consumer hardware so this is my introduction to commercial hardware.

@wkdpaul 4 ай бұрын

Best mod for this server is the ILO fan control firmware. I have that exact model and with the modded firmware, it's dead silent and doesn't overheat.

@mrb8308 4 ай бұрын

Thank you! I found that the fans were running at 80%+ because of the PCIE cards I installed. This helps and lead me to now know why the extreme fan noise started.

@mrb8308 Ай бұрын

I finally got a script to work that I run after a restart. I haven't figured out a script that will automatically run when I reboot Windows Server 2022. I made the script just every fan sensor pid lo 35. With the problem sensors pid having a hi of 35. Finally something quiet 🤫 till I start multiple backup or running network rendering using DaVinci Resolve Studio 19

@MTS_IT 3 ай бұрын

There is a patch for ilo (4.22 i think) that allows you control fans (and it s actually rather quiet after patching)

@mrb8308 3 ай бұрын

@MTS_IT I am still fighting, making the patch work on mine. The problem is that the non-compliant PCIe cards set the fan speed to extremely loud mode. 😳

@shephusted2714 8 ай бұрын

i like the creative use of cement board - the old server are too loud and use too much power but where else are you going to get that much ram capacity - no where - good content and creativity in this one

@mrb8308 8 ай бұрын

Except for the Hard Drives, all the cables, Server, Expansion hard drive bays, PCiE and so on was just over $200 even with all the extra RAM. With the dual CPU at this set up it is as fast as i9-9900K for a fraction of the price.

@NexGenStudios.Global 7 ай бұрын

are the fans hotswappable

@Saltiine 2 ай бұрын

how is the power consumption

@mrb8308 2 ай бұрын

@Saltiine normally idle is less than 200 watts. I have seen as low as 156 watts. But, large file transfers are above 300 watts, and it says peek is 450 watts. I am running a 4K graphics card. I also am running the iLO 4 fan modification with fans running at a minimum "p" of 35. I also have a small fan running off the internal USB port that blows on the RAID controller and Hard Drive controller. The wattage stated above is not total system wattage. It does not include Aruba S2500 48T-10G-4 switch, the four drives in the external four bays or the sound system.

@davidhenzler4817 10 ай бұрын

I actually returned the card as in my case using Linux Mint, the software upgrades caused the mouse to fail. I'm assuming IRQ conflicts. I gave up on those back in the days of early Windows. Bought a MSI Nvidia card with 2G of RAM and it works flawlessly and doesn't need any updates. Not running the card at full capacity I operated the server with it for a couple days and noticed no severe heat problems. But under a load, I'm sure it would warm up. My fans didn't ramp up. I'm using a Gen9 server and it kept quiet... fans running at 19%... Thanks for taking the time to respond....

@bajerra9517 9 ай бұрын

Hey Mr. B, great job on the HP Proliant DL360 Gen8 upgrade! I really enjoyed watching your video and learning about the process of upgrading your server. I was wondering, though - how did you connect your server to your display? Did you use an VGA-VGA or VGA-HDMI cable or something else? I'm trying to set up a similar setup at home and would love to know what cable you used. Thanks again for sharing your experience!

@davidhenzler4817 10 ай бұрын

Could you elaborate on how to reverse the air flow on the fan... I believe you said that you did this... I'm running a DL360gen9. Please contact me about this...

@mrb8308 10 ай бұрын

I took the fan motor off the video card by unscrewing the four screws and put it on upside down. So the fan is blowing out of the case lid door that I drilled to be the size of the fan and lines up once closed. This was done to avoid the fan fighting the much stronger Server fans. Make sure I got the fan direction right before you just take my word for it.

@markuspesch9083 9 ай бұрын

Cool thing, what kind of NVMe adapter did you use for your 1TB NVMe M.2?

@ateskaratas 22 күн бұрын

bu bilgi bana da lazım. dl380p g8 kullanıyorum. ssd adaptörleri verimli oluyor mu?

@jeffparr1 10 ай бұрын

This is far too load for a Gen 8, Yes it is somewhat loader than a PC but after the iLo initialisation the fans should wind down unless ther is an error condition. The flashing orange led on the front indicates an error. If you are not using both PSU make ensure that the unused one is pulled out a little so it is disconected otherwise the system will interpret this as a failed PSU and with spinn the fans at full speed

@digitaltechnical2691 2 ай бұрын

@hackenforst4940Check to make sure one of the fans hasn't stopped. If one fan dies , the rest run full open all the time.

@abdullatifabdu 2 ай бұрын

Hi, what kind of NVME adapter did you use for hp prolient DL360p gen 8 ?

@mrb8308 Ай бұрын

@@abdullatifabdu just a cheap two slot PCIe card adapter off Amazon. I actually bought the cheapest one I could find with a five minute search. 😅

@TanzaniaCommunity Ай бұрын

@mrb8308 Do you the link of because right i have hp prolient dl360 gen 9, can you help find the link

@RWD_Faiz 5 ай бұрын

Do you have an external PSU for the other disk outside of the server? Is it connected in anyway with the server or just running on its own?

@mrb8308 5 ай бұрын

Yes, I have a 300w PSU and a 750w APC UPS Battery Backup in the empty space behind the external four bay hot-swap drive setup. Gives the server just enough time to shutdown safely.

@RWD_Faiz 5 ай бұрын

@@mrb8308 Understood 👍I am looking to do the same with my G9 just waiting on the parts to arrive :)

@bzmrgonz 8 ай бұрын

HOW OFTEN do you dust your rigs? I see a lot of sawdust ontop of the particle boards.

@DiyintheGhetto 11 ай бұрын

That dual nvme drive card that connects one sata nvme and one pcie nvme. Wondering why you didn't use a dual pcie nvme ssd card? Does that server have bifurcation on it?

@mrb8308 10 ай бұрын

These where both repurposed from other PC's that were upgraded. This project was to be to reuse as much as possible from repurposed hardware. Having a few 4GB video cards that actually fit was cool for me. As well as having the SSD for the Windows 2019 and the 1TB NVMe for RAID buffer.

@DiyintheGhetto 10 ай бұрын

@@mrb8308 Ahh I got you Nice!!