#hqs

  Рет қаралды 3,370

Jedi3

Jedi3

Күн бұрын

Пікірлер: 8
@paulthompson1654
@paulthompson1654 2 жыл бұрын
hi Rusty cars are best to have body shells dipped /stripped . That way you massively reduce of rust ever coming out again .
@stevenJEDI3
@stevenJEDI3 2 жыл бұрын
G’day mate where I live there’s no one around here that does that but it looks like I’m replacing a lot of the steel anyway I’m taking my time to do a lot of preparation before I seal up anything and make sure I use a good quality rust converter to stop rust ever coming back hopefully Do you know what it cost to get a car dipped I’ve only ever had things Sandblaster
@nathanmacready872
@nathanmacready872 2 жыл бұрын
Mate I’ve been trying to find a video of someone replacing the inner sill panels for a while. I have the exact same issue as you on my HG kingswood wagon. Both inner sill and outer sill are gone and I’ve never replaced them
@stevenJEDI3
@stevenJEDI3 2 жыл бұрын
G’day mate I had the same issue, I looked and I couldn’t find anyone who had done an inner sill only outer I’m going through the whole car I just ripped out the back floor today I’m going to Mini Tub the car also and redo the boot Rear quarters also under the front windscreen it’s my first attempt and I’m finding it not that hard to do
@nathanmacready872
@nathanmacready872 2 жыл бұрын
@@stevenJEDI3 mine is also my first restoration, I’ve cut out the plenum and next will be the dash as it’s rusted really bad. My drivers side sill is toast and most of the floor
@stevenJEDI3
@stevenJEDI3 2 жыл бұрын
I’ve just been taking plenty of measured photographs and keeping everything at the moment that I’m cutting off, so if I run into a hick up I can look back at photographs or all the parts
@nathanmacready872
@nathanmacready872 2 жыл бұрын
@@stevenJEDI3 that’s a smart idea… I’m so worried about bracing and supporting the whole car. I started cutting the plenum chamber out and then freaked out that I twisted the car. Everything I doi worrie am I doing it right because I’m not a pro at this. I’m just using common sense and asking guys with experience..
@stevenJEDI3
@stevenJEDI3 2 жыл бұрын
@@nathanmacready872 I’d say don’t stress just do your best and I’m pretty sure you wouldn’t get any panel distortion by taking out the front plenum and Cowell, I’ve removed mine and I’m waiting for some 1.2 Cold roll steel So I can make a start myself
#hqs Holden HQ mini tub part (2) 1974
25:34
Jedi3
Рет қаралды 2,7 М.
Правильный подход к детям
00:18
Beatrise
Рет қаралды 8 МЛН
黑天使被操控了#short #angel #clown
00:40
Super Beauty team
Рет қаралды 52 МЛН
If people acted like cats 🙀😹 LeoNata family #shorts
00:22
LeoNata Family
Рет қаралды 40 МЛН
[BEFORE vs AFTER] Incredibox Sprunki - Freaky Song
00:15
Horror Skunx 2
Рет қаралды 19 МЛН
Rust repair on a 1982 Holden WB 1 Tonner 🇦🇺
55:43
Bad Chad
Рет қаралды 791 М.
Campervan VW LT35 bodywork rust repair
34:07
PureMongrel
Рет қаралды 178 М.
The REBUILD of my WORK UTE
26:40
V8 Jake
Рет қаралды 14 М.
HQ HOLDEN SEDAN REBUILD  PART 1 THE BEGINNING
12:01
Nexgen Revamp
Рет қаралды 10 М.
XB Coupe sill panel part 1
31:06
xacoupeguy
Рет қаралды 10 М.
Holden hz sill panel replaced wingitcustoms
17:58
WING IT CUSTOMS
Рет қаралды 8 М.
Iron Empire EP 70 - HQ Holden gets 3 day facelift!
16:40
The Iron Empire
Рет қаралды 100 М.
HX One Tonner Build - Plenum replacement and repairs
16:08
Shenke Garage
Рет қаралды 20 М.
Правильный подход к детям
00:18
Beatrise
Рет қаралды 8 МЛН