HS400 Primary Clutch Removal 1 0

  Рет қаралды 18,078

brian perry

brian perry

Күн бұрын

Пікірлер: 11
@kr3392
@kr3392 3 ай бұрын
This was really helpful 🙏
@cliffknight9549
@cliffknight9549 3 жыл бұрын
Why do so many insist on calling these variable pitch pulleys (sheaves) "clutches"? They are not and it doesn't matter who calls then such, or how many times they are called such--they will not become "clutches". Actually the drive pulley is a "variator" and the driven a "torque multiplier". The clutch is on the crankshaft inside the clutch bell which is an integral component of the variator shaft.
@bradymxr4659
@bradymxr4659 3 жыл бұрын
Cause it’s a different type of clutch on the outside similar to that of a snowmobile. The inside is called a wet clutch.
@mikesautomaintenance5780
@mikesautomaintenance5780 3 жыл бұрын
That motor looks brand new why would there be no grease on the rollers?
@pavelnovak1476
@pavelnovak1476 Жыл бұрын
Where to buy such engine? How much cost
@chriswilliams2652
@chriswilliams2652 3 жыл бұрын
What was the symptom of the ungreased Rollers? Like someone else said, the motor looks brand new. Now I'm worried my brand new ut400 has ungreased Rollers from the factory. I did notice most of my zerk fittings were ungreased. I have a intermittent symptom of what seems like a slipping belt. I shift to forward and begin moving forward for a second or two when there is a clunk and movement stops. It seems to catch up and movement continues. This dude is a month old and I have been following break in procedures.
@cotyleavitt4317
@cotyleavitt4317 Жыл бұрын
Just took mine apart, no grease from factory and I put 3000km on it like that
@garrychilders810
@garrychilders810 Жыл бұрын
Same thing with mine. Do not have to pull the motor out
@dgmenace73
@dgmenace73 4 жыл бұрын
I got a question. I just removed my primary clutch and it all looks ok....I did notice something after pulling off the back side of primary with fan fins on it off. I noticed it looks like that back section has been rubbing against the inner casting of the wet clutch? Any suggestions with this?
@bradymxr4659
@bradymxr4659 3 жыл бұрын
It shouldn’t unless something was in there or something is bent but you should then feel vibration.
@blakebowers9553
@blakebowers9553 8 жыл бұрын
I can't get my clutch housing off after removing the bolts!
Massimo Msu 500/700 clutch
37:56
Limitless Powersports service & repair
Рет қаралды 20 М.
Friends make memories together part 2  | Trà Đặng #short #bestfriend #bff #tiktok
00:18
Who’s the Real Dad Doll Squid? Can You Guess in 60 Seconds? | Roblox 3D
00:34
Сюрприз для Златы на день рождения
00:10
Victoria Portfolio
Рет қаралды 2,7 МЛН
Human vs Jet Engine
00:19
MrBeast
Рет қаралды 164 МЛН
UTV Clutching 101: Everything You Need to Know and More!
6:39
Vivid Racing Off Road
Рет қаралды 250 М.
Hisun UTV Wet Clutch & One-Way Bearing Replacement
14:59
Jerry Don Pagitt
Рет қаралды 28 М.
Clutch Removal & Belt Inspection - HISUN 550cc UTV Engine
5:13
Let's talk about wet clutch setup, adding slugs & the many issues we all have.
19:34
Limitless Powersports service & repair
Рет қаралды 5 М.
Coleman UT400 Belt Replacement
6:27
RG Small Engine
Рет қаралды 6 М.
Rhino 660  Primary & Wet Clutch Removal
19:07
Rhino Rider
Рет қаралды 113 М.
CVT Drive System
5:56
bennche
Рет қаралды 74 М.
Friends make memories together part 2  | Trà Đặng #short #bestfriend #bff #tiktok
00:18