Hubsan H502S Worlds Cheapest GPS Follow Me FPV Camera Drone Flight Test Review

This GPS camera quadcopter is currently the least expensive ready to fly to include FPV, follow me, and real GPS return to home/landing capability. Buy it here www.banggood.co... or here from Amazon amzn.to/2nMG6LW and also here amzn.to/2nMIWAI
Pro's
Currently the lowest cost RTF GPS equipped quadcopter with follow me mode.
Also includes 5.8 Ghz FPV. Receiver and monitor is built into the transmitter.
Includes on screen display of telemetry information
Includes position hold, headless mode, follow me, and return to landing.
Will automatically fly back and land at its takeoff point upon activation of the return to home switch, or automatically if the quadcopter loses signal from the transmitter such as from flying out of range, from electrical interference, or if the transmitter is turned off (but don't deliberately turn off the transmitter to test this).
Includes 2MP still pictures, 720p HD video camera.
Small and safe quadcopter. Should be able to fly this most places without being hassled.
Pretty good flight time at ov er 11 minutes for the "S" version (slightly more on the "E" basic GPS version).
150 grams weight. Does not require FAA registration.
Cons
Although with very advanced features, the quadcopter also is equipped with brushed motors. You may need to replace a motor some day.
Does not come with needed microSD card or card reader to record and download camera's video.
Description:
Brand Name: Hubsan
Item NO.: H502S
Item Name: Hubsan X4 H502S RC quadcopter
Frequency: 2.4G
Channel: 4CH
Quadcopter Size:165*165*60mm
Weight(including the battery):140-147g
Battery: 7.4V (2S) 610mAh Li-Po Battery 35g
Built-in HD camera 720P .
Motor: coreless 0820 x4
4 LED indicators &Rubber feet
Max Flight radius:200±15 m
5.8G wireless video transmission
Flight time: around 12-13 minutes
Charging time: around 30-40minutes .
2.4G FPV Transmitter
Battery: 4*AA (Not included)
4.3 inches LCD (resolution: 480*272)
Function: Headless mode ,GPS, Altitude Mode .RTH function .Failsafe mode.Automatic calibration.Follow me function .
Features:
Built in 720P HD camera are tuned amazingly to capture stunning pictures and videos from the sky.
With GPS auto positioning system, accurate positioning location, perfect advanced follower.
Follow me mode with GPS enables the H502S flying itself to capture your adventure wherever you are.
5.8G FPV Real-time Video Transmission: Share the videos and photos to the LCD display at anytime anywhere
With headless mode function,no need to adjust the position of aircraft before flying ..
With one key return function, makes it easily to find the way home.
Package Included:
1x H502S RC Quadcopter, 1x Transmitter, 1x Battery
This video along with every video of the Quadcopter 101 channel was produced and edited with VSDC Free Video Editor. You may download this excellent, and no kidding "free" video editor here www.videosoftde...
Affiliate links: At no cost to you, I do receive a small commission for sales resulting from these links.
MUSIC LICENSE
"Awel" by stefsax
ccmixter.org/fi...
is licensed under a Creative Commons license:
creativecommons...
music was shortened to fit length of video.

[@Quadcopter101]

*Buy it here* goo.gl/12Ba3f , or here *from Amazon* amzn.to/2nMG6LW and also here amzn.to/2nMIWAI

[@tomjack9897]

Quadcopter 101 c

[@briancotton5111]

Quadcopter 101 h

[@gerryr1893]

Quadcopter 101 is this better than cheerson cx 20 Thanks

[@chrisvillanueva4125]

hey quadcopter 101 i need ur opinion. i need a quad for photography with altitude hold. whats the cheapest that i can buy? i just need to practice before buying a high end drone thanks very much for your videos mate very helpful

[@thelongranger55]

Quadcopter 101 can you record on the remote like a dvr. ? Like can you record what you view on the screen as well as record on the drone separately ? , I seen in a video there is a micro chip on the side so is it for recording the telemetry/fpv screen

[@clvdh7236]

In the model that I purchased in December, 2016, there is a female JST connector located at the top of the battery bay that allows for a LiPo battery to be plugged in. The exact same LiPo battery provided when you purchase the quadcopter fits exactly into the battery bay. It is a little snug but it does fit and the battery cover can be closed. It is not mentioned in the literature provided with the copter as an alternate but I went ahead and plugged it in and gave it a try. It worked just fine. It also registered a full charge on the meter on screen. Even when fully charged, my rechargeable Energizer 2500 mAh NiMH AA batteries only registered two or three bars. The advantage here is that you can use either the LiPo battery or the four AA option and you don't have to hack up the transmitter. My battery bay is a little different than others that I have seen in that it does not have a divider between the two battery rows which allows for the LiPo battery to fit in the bay.

[@ThaRyddla]

Is there any way to calibrate the follow me mode my camera points away from me at about 30 degrees to the right of the controller...........but it follows im just not in the shot.

[@Quadcopter101]

The accuracy of it pointing directly at you varies with the GPS position accuracy of both the transmitter and the quadcopter See the video above where I discuss this starting at 18:44 It's best to place the quadcopter at least 10 to 20 meters away for best results with follow me.

[@ThaRyddla]

Thanks quadcopter 101 and Dustin Dunhill are the only reviews I watch the rest I just test on my own, I am actually the one that first responded to Parrots Skycontroller having the emergency button so close to the right hand, I demanded a remap sequence software of the controller, and it was done. Parrot is a great company to work with the engineers. I have a new Bebop 2 on the way due to a malfunction in their new follow me mode software which im against being is already cost me for the flight plan..........double charges.

[@n1tlf470]

I think the reason why the video was corrupt on the transmitter screen , was because maybe you need to program the transmitter for the right video frequency in the 5.8 GHz band. If you're one channel off, it looks corrupted. You can program that particular transmitter for different video frequencies in the 5.8 GHz band. It's programmed separately from binding it to the quadcopter flight frequency which is in the 2.4 GHz band. Maybe that might help

[@leonmays557]

There's a black dot on the sun if you look in the middle on 12:20 to 13:00

[@Quadcopter101]

That's the "Black Hole Sun" that Soundgarden warned us about. But seriously, that's the sun's brightness overpowering the cheap image sensor in the camera.

[@BloodTar]

GPS operates thru cell towers NOT satellites. Ever notice that when you're in an area that doesn't have cell service that you also don't have gps service? That should be all the proof you need.

[@Quadcopter101]

spaceplace.nasa.gov/gps/en/#:~:text=GPS%20is%20a%20system%20of%2030%2B%20navigation%20satellites%20circling%20Earth.&text=A%20GPS%20receiver%20in%20your,is%20surrounded%20by%20navigation%20satellites.

[@BloodTar]

@@Quadcopter101 ... Sorry, but NASA lies about a lot of shit a lot of the time. If GPS was actually bouncing off of a satellite then I would never lose a GPS signal here in the mountains......but I ALWAYS do.

[@Quadcopter101]

Trees (mainly the water in their leaves), mountains, and buildings (try getting a GPS fix near skyscrapers or in a tunnel or parking structure) can block some of your view of the sky. This in turn blocks reception of some of the GPS satellites. You usually need a minimum of 7 in direct view to calculate a good GPS position.

[@kjvoller]

Many thanks for really good and understandable video, have already ordered one of these. One question, do you need to calibrate the compass giros before every flight

[@Quadcopter101]

Yes, each time that you change the battery the drone will go into compass calibration mode automatically.

[@madhavgautam5357]

Hello brother! I am also planning to buy this drone so can you please tell me that is this drone durable? I mean I heared that it's motors stop working after a while so I want to know your experience.

[@FerralVideo]

On the note of it being safe; This quad is equipped with an emergency shutdown feature. If the props strike something, such as an obstacle or, well, you, and the drone can't restart them for more than a moment, it'll lock the motors and shut down on the spot. It will also shut down if a motor does not start properly during the unlock spool-up. (Which can be a bother if you're trying to fly on a worn-out motor because your spares haven't arrived yet.)

[@johnheitz4427]

Hello 101, Bought my first Drone Hubsan 502E worlds cheapest drone with GPS base on your review and LOVED it! You cant go wrong with this $80 Drone. then moved on too the Blade 350 QX , QX2 and QX3 Family and frankly their not as fun as the Hubsan and the WI FI on the cameras create problems. Last night I ordered the Hubsan 502S with follow me and the built in screen. I am sure I will Love this one even more. Cheaper can be better for the beginner Drone flyer and more convenient. I keep my Hubsan 502E in a brief case in my car and fly it on my lunch break that often draws a crowd. I enjoy your reviews on Drones and often look for the videos With someone holding it in front of the camera! John in Illinois

[@madhavgautam5357]

Hello brother! I am also planning to buy this drone so can you please tell me that is this drone durable? I mean I heared that it's motors stop working after a while so I want to know your experience.

[@johnheitz4427]

@@madhavgautam5357 still flying mine! Yes I had to replace one motor

[@timm2020]

Can you add external antennas and paddle antennas to the transmitter?

[@jimmytyler4457]

Question. I just received my H502S Have it 2 days and flies great. My FPV screen cuts out and goes blank on me after I back away 3 feet or so , then the transmitter looses the picture. Monitor goes blank. I opened the transmitter and both the FPV transmitter connectors have hot glue all over them, so does the antennas. will that hurt the transmission? If not can you help me?. When the drone and transmitter are close to each other It has a good picture .

[@Quadcopter101]

Close it back up and don't mess with the internals. It sounds like you are currently on an unusable FPV channel with a lot of interference. Go into the transmitter's menu and try different channels to improve reception. kzbin.info/www/bejne/oarJYp2geqZ6rqc

[@madhavgautam5357]

Hello brother! I am also planning to buy this drone so can you please tell me that is this drone durable? I mean I heared that it's motors stop working after a while so I want to know your experience.

[@chrisduncan3943]

Is the video quality on the screen good enough to fly FPV? On my H107D, the screen flickers and cuts out at a short distance but when I use my Quanum FPV goggles I get much better video range.

[@jidiwen7533]

flight distance around 300m

[@GODMOTHERLIMO1]

hi i have a 502s an rear left motor and rear left led not working after crash plz help ive checked for loose connections all appears well you seem very knowledgeable what could i check for what would cause an engine an led to stop working little info drone brand new flown 4 times no problem then while in rth i touched or did somthing an the 502 fell pretty hard on its top an cracked open put back together gets gps an arms but no rear left motor or led any advice you have is greatly appreciated love my 502s and would like it back in the air where it belongs an not on my dresser again thanks for any info and your fellow drone enthusiasts

[@Quadcopter101]

Broken electrical connection, somewhere between the motor and the flight control board. Likely a broken wire, or a separated solder joint. You (or someone else) is going to need to open it up and find where the broken connection is.

[@tiagotiagot]

Why don't they take off with just gyros, accelerometers, and barometer, and then do a few flips and rotations to calibrate the compass automatically?

[@Frank-uf2vn]

Great video, are you able to see where the quadcopter is flying (real time) right from the top of the controller & how many feet can it clime to, I'm sure the height you were at in the video wasn't its max height?

[@무난-w7g]

Which do you think is better? This one or h216a?

[@ronm1662]

For a sun shade, try the one for the Proto X-fpv. I got one for my x-4 h107D and it's a perfect fit (mad for the TX) so I think it would fit the 502S. it is like $6 or so on eBay, search "Proto X-fpv parts".

[@gerrylittle6512]

Question..Is there a app that will allow me to connect my camera to my phone so I can use it in my googles? Like how my boscam connects to my 502s

[@Pete391]

With these drones do you have to be in line of sight of the drone for the controller to control the drone...

[@LowCostCncRetrofits]

So have they fixed the problem yet with the brushed motors burning out on the newer model ? Cheers for Australia : )

[@georgekincel7108]

I always check your reviews before purchasing, thank you for that. On my H502S transmitter, pressing and holding the video button initiates circle mode.

[@MikeDesertHunterHale]

Did you ever learn how to run your little quad, (the Hubson 502S)? and did it hold up to use?

[@revo2321]

i have a question i have a spayhawk airplane controller with screen is it possible to control this dron with it??

[@Quadcopter101]

I'm not sure. But it sounds like an interesting idea. Maybe someone else here has tried it already?

[@revo2321]

probably.. btw keep it up buddy we love your videos! im thinking of buying a drone, what do you recommend the "upair on 2k" or the "husband 501s"?

[@bluesman3794]

have you tried turning of transmitter to see if it would return home?

[@attemptedpro1051]

I know I'm very late but do you think the the h502s is worth 80$ more than the h502e for a beginner

[@Quadcopter101]

If you're a beginner, would recommend skipping the FPV. I have more than enough fun with the cheaper H502E kzbin.info/www/bejne/hH3NY5uni6hnl6M kzbin.info/www/bejne/joScZJSQeKyHhJo kzbin.info/www/bejne/ZpzShWWll7ONqM0

[@attemptedpro1051]

+Quadcopter 101 thanks! love the review!

[@nor4277]

I wish I could show you all that lock tight on the screws ,and I had several.people tell me two of the prop screws are counter clock wise ,there is a silver set of and a black set of screws ,I can't remember ,which screw goes counter clock wise ,on my 502 E at first I tried the screws all clock wise that didn't work ,hubsan sent me another set that were hard to turn ,I got two in clock wise and two in counter clock wise ,I hope I didn't screw up anything

[@DaKurupt19]

Why do you do the compass calibration different than they tell you? IE spinning the quad in place instead of your whole body with the quad.

[@mmmartin261]

Nocturnal calibrate 1 SPIN HORIZONTAL CLOCKWISE. Calibrate 2 spin cam down batt up clockwise. Every battery change I think. Mine almost lasted one week. Amazon JYZ sent me someone else's returned item.

[@tonycao705]

should I buy 507A or 502S? 507 has some interest points like way-point fly and cheaper than the 502s but it looks that 507 has a short fly range due to the wifi and a shorter fly time. Is that all true?

[@imanishay]

What's the difference between brushed and brushless motors and why are brushed a bad thing. Also where can you buy spare batteries for this thanks

[@jenniferguinan6531]

My 10 year old son flew this quadcopter all weekend on our vacation but when he returned home and tried to read the microSD card there were no videos or photos showing up on it. He inserted the SD card into the quadcopter correctly. Does he need to have a microSD card in the transmitter as well as in the quadcopter? Or did he not press the video/photo buttons correctly?

[@Quadcopter101]

Was there really no files recorded? Or were there files, but they were not viewable 0 Kb sized files? If the latter, then he likely did not press the buttons correctly. It's very important to remember to stop the video recording before powering off the quadcopter. If he forgets to do such, the video file will be corrupted and unreadable.

[@LazyTuberTheGamer]

Where is the recorded video stored? (h502s)

[@RonaldBrown59]

Since this doesn't have a gimbal, just GPS to hold it study, do you get the jello effect in the video it records?

[@Quadcopter101]

+Ron Brown watch the video and see ;-)

[@RonaldBrown59]

I did watch the video and I thought it had some jello effects. But take that with a grain of salt considering I've only ever flown to camera quads: the Syma X5c and the Phantom 4 and you have flown at least a 100 different Quads. Syma had almost all jelllo and the Phantom has almost none. I was looking for something in between but leaning toward the Phantom (as far as camera shake goes). And I would like your expert opinion as to where this falls on the jello effect scale. Great KZbin Station, I love the content you produce and if I buy I'll be sure to use your link.

[@Hugo-ql6kn]

Quadcopter 101 i have a mjx x601h drone but i have the old remote control, how to i use altitude hole mode on the old remote control?

[@Quadcopter101]

Not sure that it's possible as the X601H controller's throttle is spring loaded to center position for altitude hold. Also not sure that they can bind. But you can still easily fly the X601H easily with your smartphone. Watch the following video, and advance it to 17:30 into the video to see how kzbin.info/www/bejne/Z4aVm52Kd85lj9U

[@nintendoswitchcube6463]

in the url its 150 pounds how do you set it up with the compass thing and the satalites?

[@NoviceQuads]

I have one now and even modded the transmitter. I get between 450 and 500 meters now.

[@munirmuhammad1230]

How u did it

[@sd-pr6ls]

Hey. Another question. I'm using this drone and lately one of its propellers can't rotate smoothly, its slower than the other 3 and has difficulties to start. Sometimes it needs a little finger push in the begging and then it rotates and can fly. The problem is that that drone keeps going up, i can barely get it back and I have no control on it. I think the problems are connected. I tried to change it to one of the spare propellers but it doesn't help, do you think the problem is in the motor? Do you too think the problem of controlling it has something to do with the problem of the propeller spin? Will I be able to fix it myself by buying a new motor? Thanks!

[@Quadcopter101]

Gently turn all of your propellers by hand. Do any have unusual resistance in turning as compared to the other three? They should all spin freely with no resistance. If you notice any unusual resistance or grinding while turning, then you likely have dirt stuck between the gear teeth. Do not fly with this resistance, or you will burn out a motor. You can remeove the bottom plate of that propeller arm to gain access to the gears. Use compressed air and/or an old toothbrush to remove large chunks. Slide a pin between the gear teeth to remove stubborn sand particles stuck between the teeth. Continue doing such until the propeller spins freely with no bumps in its rotation.

[@MALNTV]

Have you tried strapping on a Firefly Q6 to this quad? This would make a good poor mans 4k camera platform since it’s gps and FPV. But I’m worried the brushed motors won’t handle the payload.

[@marcosmovies7871]

Can u maybe do a video on a dji phantom 3 standard with the litchi app ? I heard that it extends the abilities of the drone

[@squadcopter3880]

Is there a larger battery you can use with this quadcopter to get a longer flight time?

[@ΚωνσταντίνοςΜιχαλισλής]

I don't think so because the space is limited.

[@lakshyagaynar7520]

Which frequency band does it transmit? Can i use my fpv goggles with it?

[@RigaRoosterMikeJohnson]

Hi - QUESTION??? -- I am experiencing a problem with the "compass dance" not wanting to complete compass 1. I have bound and turned at least 8 times with no success. I am indoors close to a window. Is being indoors part of the problem? Any suggestions? Also, the battery life using AA Alkaline batteries is very, very short, so I am going to make a conversion to a LiPo battery. QUESTION??? what is the smallest LiPo would you recommend for this task? Is an 800 maH big enough?

[@Quadcopter101]

I know. For the way shown in the manual, it takes forever to calibrate. Instead try doing the compass calibration as shown in the following video kzbin.info/www/bejne/hH3NY5uni6hnl6M And instead of LiPo, recommend AA rechargeable batteries. They have 5 times the power and endurance of normal alkaline batteries.

[@RigaRoosterMikeJohnson]

OK< thanks, I have watched this and will attempt it tomorrow as it is now night here in Europe.

[@cuylerwilkinson4414]

i follow a ton of your reviews. i need to know transmitter/receiver range in transmitting feet. where can i find a guide?

[@kheb128]

cuyler wilkinson I can give you it in meters, I got about 40 meters up, and 150 out and the transition was good, but that was it's range. I'm gonna try and go out farther though

[@cuylerwilkinson4414]

thanks for the info. i just wish these companies would provide better documentation to make a better decision

[@stephaniebergstrom180]

Hi - great review! We are having trouble with the video recording black. We tried a new micro SD and followed your instructions and it's still happening. Have you run across this, or do you have a recommendation to fix?

[@Quadcopter101]

Card must be no larger than 32GB. Also remember to stop video recording before turning off the drone, or the video file will be corrupted.

[@MrEbringman]

Thanks for all your videos, I only started flying quads in September 2017, I have seen several reviews of the 502s & e that have had problems with the camera focus, did you need to adjust that on any of yours, thanks in advance Edgar

[@Quadcopter101]

No mine was fine out of the box.

[@madhavgautam5357]

@@Quadcopter101 Hello brother! I am also planning to buy this drone so can you please tell me that is this drone durable? I mean I heared that it's motors stop working after a while so I want to know your experience.

[@AR72239]

Hi, what would be the best way to put a keychain camera on a mould King super s drone? Thanks

[@Quadcopter101]

Velcro

[@AR72239]

Ok cheers mate

[@AR72239]

Is there a link for which Velcro to buy and keychain camera, because I don't want to be buying the wrong ones.

[@Quadcopter101]

Here's the camera www.banggood.com/808-NO_16-HD-120-Degree-Mini-Camera-Module-7g-p-82197.html?p=RB0922217402201307U3 And any hook and loop (velcro) tabs with sticky backing should work.

[@Quadcopter101]

See how I attached it in this video with Velcro kzbin.info/www/bejne/a4DMqn2kqM2pq6c

[@wildhog3217]

Will the H501S transmitter work with the H501C or the H502S transmitter work with the H501C????

[@AR72239]

Do you know the Mould King 33041a how to I get the return home mode to work, and how do I calibrate it? Thanks

[@AR72239]

Do*

[@Quadcopter101]

The 33041 and 33041a do not have a GPS, thus they really don't have a true return to home capability. But they do have "one key return". All one key return does when activated is fly the quadcopter in the opposite direction that is was pointed when it took off. Thus it's very important to keep the quadcopter located down the direction that it was pointed at takeoff for it to return in your general direction. For the 33041a, it's demonstrated at 3:50 in the following video kzbin.info/www/bejne/haKtp6WiZauVqrs

[@pIRatZE]

nice watch..what watch is that you're wearing?

[@dannychan2241]

Hi Quadcopter. I am a beginner of playing quadcopter. I plan to bring this toy 502s out for hiking with my wife. I saw many people would lose control with their quadcopters even for professional grade like mavic and phantom3. Do you have any advice on how to avoid losing control of quadcopters? Also, if I want to get a FPV goggle for this 502s, which brand do u suggest? Thanks.

[@Quadcopter101]

Most important thing is to verify that you have sufficient satellites before taking off. I like to wait for 8 or more. Also, always hover for about ten seconds after takeoff before sending it out. You want to verify that the quadcopter is holding its position with no toilet bowl wobbling (circular movement like its being flushed down a toilet). If you notice any unsteadiness, land and redo the compass calibration. And finally, minimize flying at high speed rate. Sometimes at high rate, the quadcopter can get ahead of the GPS being able to keep up with calculating its position. This can cause toilet bowl effect also. If you notice such while flying high speed, slow down or hover to let the GPS catch up.

[@illson12345]

Other than the GPS, Is the flying performance of H502s much better if compare with those similar size drone with 5.8ghz FPV and altitude hold such as X5G/509g/CX-32/H8D? Because the price difference is quite big

[@Quadcopter101]

Range is about 3 times greater than all three. It also has follow me mode. But you're right, it is pricey. The following is a buch better deal IMO, but does notinclude FPV kzbin.info/www/bejne/ZpzShWWll7ONqM0

[@HarleyTom53]

I just received my 502,, my came with the props attached, I wanted to install the prob guards buy 1 screw was to tight to removed, I decided to leave them off,, I lost 3 screws trying to re-install the blades,, so far I'm having bad luck,, if I can get the screws in I think it will be ok, except the 1 screw that is to tight to un-screw. Thanks for you video

[@Quadcopter101]

Make sure to install the propellers on the correct motors. There are two counter clockwise shaped propellers, and two clockwise shaped propellers that must be installed on corresponding CW and CCW motors. If one is installed on a wrong turning motor the drone will not lift off. If confused, take a close look at the following picture, paying attention to the two different shapes of propellers and which motors that they're installed to. Make yours match the picture i0.wp.com/www.rcdronearena.com/wp-content/uploads/2016/02/Hubsan-502-E_result.png

[@HarleyTom53]

Thanks I just removed 1 prop and trying to re-install it to the motor, but having a hell of a time fitting screw into the hole,,, thanks for the info

[@Quadcopter101]

Take a very close look at the bottom of the propeller near the shaft. Notice the tiny "i" printed there. Make sure that the "i" lines up with the flat portion of the shaft. If not, the propeller will not slide down all the way on the shaft to allow you to use the screw.

[@HarleyTom53]

Hey thanks for the info,, I will do,,, I put the drone away for a couple days so I don't get frustrated,, batteries are charged all I have to do is install the last prop,,,thanks to all!

[@reakingringpiece]

how quick can you go and the follow still follows?

[@PeterWinnett]

Can the H502s do airobatics? It seems to have a fail safe that shuts the motors down when it's upside down. Is there any way to disable the fail safe? Great Ch. Regards, Pete

[@Quadcopter101]

+Peter Winnett sorry no. It's strictly a camera bird and has angle restrictions with no flip capability.

[@Watermashen]

this looks nice but does the screen in the controller actually work? if it doesn't I will be kinda bummed I just want to get some video and camera footage

[@Quadcopter101]

Yes it works. But it's hard to see in daylight. It's best to use goggles www.banggood.com/Eachine-EV800-5-Inches-800x480-FPV-Goggles-5_8G-40CH-Raceband-Auto-Searching-Build-In-Battery-p-1053357.html

[@jonathankohl6264]

Hey 101, do you know if the 502s Will work with all eachine goggles?

[@gerryr1893]

Is this better than the cheerson cx 20 ?

[@leaseo]

Hi. recently I bought a drone and can not pass the calibration number two. As I can make this work?

[@Quadcopter101]

The easiest and fastest way that I found to calibrate the compass is shown at 2 minutes 10 seconds into the following video kzbin.info/www/bejne/hH3NY5uni6hnl6M#t=2m10s

[@trekjedi6003]

I just picked up this quad thanks in large part to this video. Its great. One thing Im concerned about is follow me. When I tried it, instead of the camera facing me it turned away. My thought is a compass calibration error. What are your thoughts. Thanks in advance. Love the channel!

[@dank6905]

There is a jst connector inside battery box,you can use spare battery from drone push it into battery box,then to left,then plug it in,it will last a lot longer regular batteries

[@rondoschiavoni8840]

just got a new Mini Omni Drone and it works very well, its just that the camera is shaky or wavy when in flight doing a video can this be fixed ? NO GIMBLE

[@Quadcopter101]

kzbin.info?search_query=quadcopter+propeller+balance

[@TheEvilScotsmanOfficial]

Just got one of these, when you take off, does it automatically go into hover mode ?? afraid to let go of the elevate stick incase it smashes back to the ground, advice would be greatly appreciated my friend.

[@Quadcopter101]

It will if you wait until you get six satellites locked in on the quaddcopter. But I don't believe that the H502S will let you take off with anything less than six satellites.Watch as I wait for satellites at 5:42 in this video.

[@TheEvilScotsmanOfficial]

Quadcopter 101 Big thanks. appreciated.

[@Web-Titans]

Video format that the recorded file is in?

[@steveh3483]

Hi, I think I am right in remembering you have a run cam on your hat? also how do you record sound, do you use the run cam or separate audio, because it is very good. Even sometimes when you have a breeze. I am considering getting the run cam v2?

[@Quadcopter101]

Actually I use a Mobius camera on my cap. Have done close to 700 KZbin videos with it, and it's still going strong www.banggood.com/Mobius-Full-HD-Sports-Camera-1080P-30FPS-720P-60FPS-For-Multirotor-p-90648.html?p=RB0922217402201307U3 And I use a Runcam for much of aerial videos. It doesn't have as good a microhone as the Mobius, but its video is pretty good, and it's shielded to prevent RF interference with your quadcopter's receiver www.banggood.com/Runcam-FPV-HD-1080P-Wide-Angle-Mini-Sport-Action-Camera-for-250mm-Frame-Quadcopter-p-1017506.html?p=RB0922217402201307U3

[@everythingzone]

Since you've basicly done all the models by Hubsan could you also do the H301S FPV Plane? Great plane

[@illson12345]

Is it really great difference between the brushless motor 501s and brushed motor 502s? I am interested in 502s due to the small size. But is there great difference when you fly the drone?

[@Quadcopter101]

+Illson Chan well yes, the brushless motors are much more powerful, efficient, and can carry the 501s 2400mah battery for much longer flight time. The 501s also has a much better 1080p camera.

[@illson12345]

+Quadcopter 101 How about if I only concern about the flight performance? I do have a P3a so I will only use it for practice and I don‘t care too much for the image quality and the fligh t time

[@Quadcopter101]

+Illson Chan but if you're looking for a small size, quiet GPS camera bird, take a look at the H502E. No FPV or follow me, but it is a nice steady camera quad that's not intrusive. Doubt many would complain about it as they may not even notice it in the sky. I'll be releasing another review on it in a few days. Check it out.

[@illson12345]

+Illson Chan I do consider the JXD 509g but the price difference between it and the 507g is not that much and the 507g seems a little bit too big for me. So I finally consider the H502s. How will it perform under wind if compare with those huge toy grade drone such as 507g or CX-35?

[@JH-bn6cv]

can i use this transmitter of 502s in 501A?

[@vpelleri1]

How do you keep track of all of the quads and controllers? Do you keep all of the ones you use for reviews? Is your garage full?

[@Quadcopter101]

I really don't have many. I don't keep them (don't have the storage space), nor do I sell them. After their reviews are completed, they are donated to local schools and charities (Toys for Tots and school STEM clubs).

[@joshjestine7197]

+Quadcopter 101 Hey bro you're a good person doing a great job. I have a question im a beginner and I bought the x5sw-1 but it lags, so do you know how to fix lag issues?

[@Quadcopter101]

Josh Justin Unfortunately the X5SW uses WiFi for FPV. WiFi allows use of your smartphone to view the video, thus allowing a lower cost quadcopter because a dedicated receiver/monitor screen is not needed. Unfortunately WiFi is not very good for FPV as it operates on the same 2.4 Ghz as your quadcopter's controller. Lag and reduced range of both the quadcopter and FPV signal are results. Not much that you can do to improve it. But for your next quadcopter, if FPV is important, recommend considering a 5.8Ghz FPV system as it operates on a different frequency than the controller. You'll get much better range, and very little lag as a result.

[@joshjestine7197]

+Quadcopter 101 but with monitor it's costs more

[@Quadcopter101]

Josh Justin This is true. Poor FPV performance is the tradeoff for flying cheap FPV ;-)

[@aurelbarbor1125]

I have hubsan 502s and after starting, the transmitter connect automatically return home without RTH switch command, including GPS mod or manual mod. How can I solve the problem? I can use the 502e transmitter?

[@Quadcopter101]

It will automatically RTH on low battery of the quadcopter or lost reception from the transmitter. Are you absolutely certain that the batteries of both the quadcopter and its transmitter are fully charged and functional?

[@aurelbarbor1125]

I use full battery for both. The RTH it's connected automatically in GPS mod, without GPS and manual mod. After the start, the quad copter elevated to about 30 feet and automatically it's connected RTH, without return lever command.

[@arthursisteminfor]

Hello! I have a motorcicle and I want to record a few roadtrips using a drone. How fast (mph) can this one go on follow me mode?

[@Quadcopter101]

Not very fast. About 20 miles per hour.

[@christopherho5821]

Can you control throttle, yaw, pitch and roll during returning to home

[@Quadcopter101]

No regarding pitch and roll, as any movement of the pitch roll joystick will cancel the return to home. And I believe that yaw and throttle control are inoperative during the return to home.

[@awolf3362]

If it has no micro SD how does it store video? How do you save the video it records?

[@christianblade2052]

Yes, it does have a micro SD slot on the drones underside.

[@wingmanalive]

I had 8 sats and my RTH function almost landed my quad on a house, some 30' away from point of take off. There's some work to be done there.

[@Quadcopter101]

8 satellites is just two above bare minimum of 6 for a GPS location fix. Although I took off with bare minimum for this video, I've learned since that it's best to wait for more satellites (I now use 10) for best GPS accuracy.

[@wingmanalive]

Problem is I have to wait a good 15 minutes even for 6. I'm not in a remote location (not that it matters to sats) but for some reason they don't come easy. Plus what scares me is if the number of available sats drops below 6 for 20 seconds or more the quad descends, even if I were above a lake.

[@Quadcopter101]

You might want to consider popping the top to make sure that the black shield is installed below the GPS module www.rcgroups.com/forums/showpost.php?p=34853718&postcount=2

[@marckyrocks0503]

Is it possible to attach onepaa x2000?

[@carlosgustavoramirez8448]

Hello, sorry I do not know if you can help me with a problem with my hubsan h502s. I made my first flight and everything worked very well, headless mode, Rth etc. But then I wanted another time to take off and could not. I already check the Rth button this off, and recalibrate several times, disconnect the drone battery and the drone only turns on the engines and tries to take off but can not. Sometimes it rises 2 seconds and falls to the ground. The motors seem to work well. I have 2 green lines of battery in the drone and 4 green lines of the command. I think the battery is fine. The drone is completely new. Do you have any idea why this is happening to me?

[@Quadcopter101]

Probably have sand in the gear teeth. With no power, gently turn each propeller by hand. Each propeller should spin freely with resistance or bumps when turning them. If you notice one of the propellers is harder to turn than the others, then the gears of that propeller likely has sand stuck in between the teeth. Do not fly any more until you clean the gear teeth of this sand. Remove the bottom foot plate of that motor pod to access the gears (remove two screws on the bottom foot, then pry the plastic foot plate off). Notice the gears inside. Gently slide a pin in between each gear tooth of both the larger and smaller gear until you dislodge any sand stuck in there. Some sand particles are very small so that you can't see them, but they will stil cause problems with the drone. That's why it's important to clean between every tooth, even if you can't see a particle. Once the propeller spins freely, reassemble, and try flying. In the future, don not land in dirt. Get a big piece of cardboard to take off and land on. Here are some more tips. kzbin.info/www/bejne/sJi5lIGZZZqFi8U

[@carlosgustavoramirez8448]

Quadcopter 101 thank you very much for your help. I'll start working on that.

[@carlosgustavoramirez8448]

Can I have your email or Facebook because I want to send you a video from my hubsan h502s camera. The video is awful and I want to see if that is normal but I want your opinion.

[@Quadcopter101]

You should be able to see what to expect from the camera in the above video. Also sometimes there is a little thin protective shipping film that they put over the camera lens. You're supposed to remove it before first use.

[@carlosgustavoramirez8448]

Quadcopter 101 yes I took it off that little film part, but the video is like if it has waves!! Is moving the image, but is not because the drone is moving which is normal but I don't know how to explain. There are like waves. The image is going like a wave.

[@JayRCManiac]

Hi Quadcopter! I had a question, you mentioned in this video, binding a 501s transmitter to a the 502s and not getting the fpv?..... Just wondering what would happened if you did the opposite. My dilema is, I have a 501s with no transmitter and was looking to purchase the 502s and use it's transmitter for my 501s using only the one transmitter for both. Will they bind ok? Will fpv and all other features work? Is there anyway you can test this for me since you have all 3 quads? I'm getting ready to place this order and would hate for it not to work. Please let me know at you're earliest convenience. Again this is in regards to being able to bind the smaller 502s's transmitter to the 501s(brushless) in hopes to have all features available when using the 501s. Thanks! Jay

[@rexopg5733]

Curious how you got one 501s w/out transmitter usually people loose their quads first, but in answering your question its possible the 502s has the same TX in fact there's a KZbin by Frequent Flyer binding the 501s to the classic years old X4 107 Tx hubsan protocol for sportsflying non centered Left stick go check it out, now if only Hubsan sell these as BNFs that would be a bargain!

[@camsandwell]

Could this carry a gopro session?

[@SuzukiKiing]

hello, I am a decent drone flyer from flying friends drones. I am looking to purchase a drone to fly for fun and maybe some video footage. I want something decently fast and under $200. what would you recommend? the syma x5-c1 or this?

[@GODMOTHERLIMO1]

ive checked and see no loose connections which leads me to think its my board but other 3 motors arm and spin could it be the board by the way love your reviews you very much helped in my decision to purchase the 502s i dont blame the quad

[@ΚωνσταντίνοςΜιχαλισλής]

GODMOTHERLIMO1 brushed motors wear out after an ammount of use

[@mauriceamaraggi8098]

I am quite a beginner. Is it stable? And can you fly it easily indoor? Thank you for your great video.

[@Bobster986]

Look like an amazing quad for the money, but I think to calibrate the compass properly you're suppose to just turn the aircraft, not spin in a big circle, that is a good why of having an accidental flyaway or failure to return to the proper Home Point if you lose connection with the controller. Also taking off before you have the correct amount of satellites will not set a proper Home Point and would defiantly cause it to Not return to home point.

[@jaimielibbi1]

Hello i am looking to purchase my first drone. i was, sorry am looking at the hubsan 501s, do you recommend thus quad, for the camera, how to fly etc. does this have a sd slot. love you channel by the way. ian

[@rayatlast]

Can it follow you while going backwards?

[@scuzzyfpv]

do you think the 502s could hold a gimbal and action cam?

[@DaKurupt19]

No

[@ΚωνσταντίνοςΜιχαλισλής]

no it can't hold much weight

[@Surferant666]

Good video 101, Now regarding the altitude when in follow me mode, do you know of a drone which will adjust its height as it follows you up or down hill?

[@Quadcopter101]

Why yes I do kzbin.info/www/bejne/ZqfJhKCnl8qjfLc

[@Surferant666]

ah ok,, lol thats a bit expensive for my pocket,, is this the only drone that can do this?

[@MrTexasDasher]

Have watch your videos and would like your recomendation of a low cost GPS Quad.

[@robflashy]

Excellent review as always. New to drone flying so had no idea what to look for but features versus cost & availability of spare batteries etc looks like this will be my choice after viewing all of your reviews including the non FPV model E and this seems a good entry flyer to see if I take to the hobby without spending a fortune & then finding out its not for me!. How does this unit compare with others in terms of the noise it makes when flying? Would you say it is loud, quiet or average? I live in a small quiet village community which already has 3 flyers who use the much bigger £1000 plus models and there has already been a few not very complimentary comments from neighbours. I am hoping a smaller toy grade unit will be less noisy to fly over the local common land which means I wont be flying over other peoples property.

[@Quadcopter101]

No worries. This small drone won't cause anyone to complain about the noise.

[@robflashy]

Thank you. Order placed & i will be taking your advice from your excellent reviews as I progress. Best reviews and advice on KZbin. THANK YOU.

[@Quadcopter101]

With that in mind, here are some tips that are applicable for the H502S. Also recommend reading the comments section of the following video for additional tips from owners kzbin.info/www/bejne/sJi5lIGZZZqFi8U

[@paulterl4563]

Ciao Quadcopter 101, it is okay if I charge his battery with a lipo charger (e4AC SKY RC LiPo/LiFe Balance Charger)? It has the possibility of 1A, 2A, 3A. At where it is better to put it? 1,2 or 3?Have a nice evening

[@Quadcopter101]

1A is best for that sized battery.

[@paulterl4563]

Thanx Q101, you the best!

[@gregory3340]

Hubsan H502S or SYMA X8HG would do you think is a better all round drone...thank you

[@Quadcopter101]

+gregory James The H502S and cheaper H502E are game changers.

[@gregory3340]

so hubsan is bettet then....can you battery mod the h502s for longer flight....great videos quadcopter101

[@paulterl4563]

Cannot heard it whistling!!???Did not whisthle?Have you said that it does?

[@Quadcopter101]

+Paul Terl it does. All H502 do.

[@paulterl4563]

okay, thank you. maybe your cam is not keepin' it. Have a good day

[@Quadcopter101]

It's a very high pitched/frequency whistle. Some people might not be able to hear it, it's almost in the frequency range that only dogs can hear ;-)

[@sd-pr6ls]

Hey, for some reason i never succeeded to record a video or to take a picture with it. tried to put the MicroSD both in the quadcopter and in the remote, in both places it didn't record anything. During the last 2 flights the screen showed no photo at all :( Any ideas? :(

[@Quadcopter101]

First off, make sure that you're not using a 64Gb card. The max size the card readers can understand is 32 Gb. Second, the card goes into the quadcopter, not the controller. The card reader in the controller is only used for updating the controller's firmware. And finally, it is very important to stop recording the video before turning off the quadcopter. Simply press the record button a second time to stop the recording. This then allows completion of the file write process. If you turn off the quadcopter before stopping the recording, the video file wil be corrupted and unusable.

[@sd-pr6ls]

Thanks! So the first problem was probably the fact that I used a 64GB one. I need to try it with a smaller one. Now I think that I have a bigger problem that I can't see the image at all on the controller screen...

[@Quadcopter101]

+steve didko do you have that problem even indoors? It's very difficult to see the screen in direct sunlight.

[@sd-pr6ls]

Yeah I'm afraid so. It worked really well on the previous flights. Can't remember when the problem started, at first I thought that it might the battery, but there's no monitor even when all fully charged. Could be a matter of settings?

[@sd-pr6ls]

I think i just solved it. The frequencey wasn't set up right. It was set to a higher number than it has to be. Thanks!

[@Dragontrumpetare]

Hmm... I downloaded that video-editor you're using. But how do I get text into the clip and to make the text bigger? I did find out how to put a little extra video into the clip though. hehe

[@Quadcopter101]

Here's a tutorial showing how. kzbin.info/www/bejne/f5eypn2OocplqNk Also be sure to search KZbin, as there are many tutorials on this program.

[@Dragontrumpetare]

Aaaah, thank you. :-)

[@Dragontrumpetare]

Aaah it was so easy ☺

[@matthew.caballero]

How is the fpv delay? Im looking for a cheap quadcopter with fpv, but i just want it to fly, not to race or get good photos. It would also be nice if someone recommended other cheap drones to me. Thanks :)

[@mmmartin261]

Had mine nearly a week before LF motor went bad/ grinding noise. Did everything but LAST. AMAZON return I think it was returned by someone else.

[@michaelsevens]

I LOVE your demos... they are so well done!!! I have bought several quads because of your demos....!!!! What you covered in this demo is genius...The up and down hill... Thanks... Did you do a review on the Walkera QR x350 I believe it was you who did a review, and you did not like it... Though it could have been someone else.....

[@raphaelmunck2079]

Cool review ! do you think I can attach (with tape) my own Yi 4K+ camera? (70g) Thank you!

[@SkunkWorks2001]

Where do you insert the sd card for recordings?

[@Quadcopter101]

There is a sd card slot in its belly.

[@sargeras304]

Can the camera be changed?

[@georgeaura]

wasn't there another one that was in the hundreds that was lower cost than this one and had gps, I think it was 106

[@sylvesterjohnson7817]

when you gonna fly h507d black and gold drone I guess its a new model

[@Quadcopter101]

No, it's been around for a while. It's the exact same as the H502S, but with a more streamlined body. It's supposed to be more wind resistant due to the shape.

[@sylvesterjohnson7817]

ohhh ok thanks I still would like to see you review one and can I get a shout out that would be great I love your reviews keep up the good job

[@Trip-Play]

How much shorter do brushed motors last in comparison with brushless? I'm planning on purchasing one and will probably use it for less than half an hour once a week. Is it going to last at least a year?

[@Quadcopter101]

It depends. I'm still on my original motors. But I practice the following to make sure that my motors last kzbin.info/www/bejne/sJi5lIGZZZqFi8U

[@Trip-Play]

Quadcopter 101 awesome! I watched the video and will apply that when I make the purchase. Thanks again. You have an awesome channel. And its great that you actually reply to questions