Hunter IIF Training: Irrigation System Overview

[@justinh6974]

Hunter irrigation systems are by far the best in the industry!!!

[@Hunter_Landscape_Irrigation]

Thanks for watching and choosing Hunter!

[@vonpoppa]

It is a great overview of an automatic irrigation system.

[@Hunter_Landscape_Irrigation]

Thanks for watching!

[@danlawrence9922]

Great overview from professional perspective for DIY- Thanks

[@Hunter_Landscape_Irrigation]

Glad it was helpful!

[@BravoServicesInc]

very good overview of the sprinkler irrigation systems.

[@Hunter_Landscape_Irrigation]

Yes, we love this series too!

[@jamesreece1502]

Definitely great video with others to go with it. I will be using these with my coworkers. Great job 👏

[@Hunter_Landscape_Irrigation]

You're welcome

[@johneverett957]

I have a well driven house/irrigation system. With pump running the pressure is set to 45 lbs. From the main water supply I have a 1-1/4" pipe out to the irrigation valves. After the valve i used 1" poly. At a spigot that is thr 1'1/4" pipe to a 3/4" spigot i am getting right around 25gpm. So I am assuming through the irrigation valve and only being dropped to 1" poly i should be getting even more GPM still at 45 lbs of pressure. My question is how many pgp adjust and nozzle number 7 should i be able to use on one zone? Also why is it recommended to use 1" main lines and lateral lines at 3/4"? I never understood what you should be gaining from doing that? Thank you!

[@gatekeeper88]

For those in other countries, the "Hot" Wire is the trigger Wire, dependant per station/solenoid.. use a 2 wire system for greater flexibility

[@Hunter_Landscape_Irrigation]

Thank you

[@grahampoplin9051]

Awesome overview of Irrigation Systems!

[@Hunter_Landscape_Irrigation]

Glad it was helpful!

[@abdulrahmanismailali1064]

@@Hunter_Landscape_Irrigation can you help me and give me your phone number

[@mrmysteryguest9]

Loving this video, all great information. I wish the audio levels were even throughout the video though. The voice over is much louder than the video host's voice. But, in any case, great info, thanks!

[@Hunter_Landscape_Irrigation]

Noted! thanks for watching

[@cspill99]

I have old copper piping ran for my wiring encase. Is it possible to run the wire through the soldered pipes. I'm thinking the issue would be the 90 degree turns. Any suggestions or should I just bury it? How deep?

[@Hunter_Landscape_Irrigation]

Industry standard it to use direct burial irrigation wire. Electrical code doesn't apply to low voltage irrigation wire but you'll want it deep enough to avoid damage.

[@deanmeyer3932]

Great content and presentation y'all; check the voltage stated at 17:05. Think you mean to say 24 volts direct current.

[@Hunter_Landscape_Irrigation]

Traditional wall mount and pedestal controllers will send out 24 volts AC current out to the solenoids. Battery powered controllers like the BTT or NODE use 24 volts DC.

[@andreiturcan9692]

What you do if you have only 2 bar pressure inlet? Do you provide pumps?

[@Hunter_Landscape_Irrigation]

Thank you for contacting Hunter Technical Support. Hunter Industries is a manufacturer of irrigation and lighting products. We do not install, repair, or maintain irrigation systems. Our product is purchased and installed by contractors. If you need field support or installation you will need to contact a local professional.

[@bsjohnston]

Great Video!

[@Hunter_Landscape_Irrigation]

Thanks for watching!

[@houstontxwill629]

Great information thank you 🙏

[@Hunter_Landscape_Irrigation]

You're welcome

[@BriAn-ki4qw]

Any plans to have an online Irrigation designer to help with sprinkler placement etc? Orbit have a fantastic one and I’d love Hunter to provide this. Would make life so much easier.

[@Hunter_Landscape_Irrigation]

Thank you for your feedback. We have lots of trainings planned for the future... Stay tuned!

[@czar89031]

i love to learn this device because i am using a hose to water my plant & fruit tree's here in Thailand 24-7

[@Hunter_Landscape_Irrigation]

You're welcome

[@johnnygarcia3761]

where is some type of training to service existing valves? remove - properly flush - replace diaphragm? the hunter video to flush a valve is a bit off and old (2010) plus rocks that big are indicative of a different problem - flush grit sediment is what I am looking for

[@Hunter_Landscape_Irrigation]

Check out this on our website that details the servicing of the valve components is linked below: www.hunterindustries.com/support/valves-servicing-jar-top-valves

[@yasseralshahrani8278]

can I get training course to design irrigation system

[@Hunter_Landscape_Irrigation]

Thanks for watching. At this time we don't have a design irrigation system course available.

[@obiedabanihani]

why the exam not show for the first video ??

[@Hunter_Landscape_Irrigation]

All exams are hosted at training.hunterindustries.com/ where you can enroll for free.

[@akselectric6040]

I doing project of 500 mm to 40 mm