thanks a lot, i needed to know which way the piston went on
@jimtelford25833 жыл бұрын
Assemble piston/wrist pin on con rod. Then use aa large zip tie over the rings then gently slide the cylinder over the piston.The cylinder will push the zip tie off the rings then just cut the zip tie.
@woodknack14 жыл бұрын
Put the piston on the rod before you put it in the cylinder head. Also you don't want to cut the gasket by the carb. It's big for a reason and that reason is to keep the air flowing on that side of the engine.
@julioamaya19735 ай бұрын
Thanks for your video I'm fix my blower 👍
@brinkee76744 ай бұрын
Jugs and pistons all over Amazon and has been for years. Before I would get them from Jack's Small Engines or who ever had what I needed. Hard to beat $27 for Jug, piston, roll pin, sparky plug, gaskets and a fuel filter-to my door I use a small filter wrench(band) to compress pistons. Ring tool at Harbor Fr for $12
@johnlee8734 Жыл бұрын
I got the same leaf blower broken completely down with it's parts in boxes in a bag. I found it in the trash and found that the spark plug was bad, cylinder, piston, muffler, are wrecked and the fuel lines were leaking and the pull start assembly is bad. I removed the gas and saw that it was crystal clear, so does that mean a bad fuel mixture? I got all the parts on order and figured someone could use it, after I thoroughly clean the parts, replace the gaskets, and get it running good.
@johnlee8734 Жыл бұрын
I've never worked on one, but it's rewarding so far.
@shadetreeautomotiveenthusi1284 Жыл бұрын
Sounds like it had no oil in the fuel. I always mix at least 50:1 in EVERY 2 stroke engine. It only takes a few minutes to wreck a 2-stroke without oil in the fuel. Some people think you can substitute transmission oil for 2-stroke oil, that's also a failure waiting to happen. Good find though man, good luck.
@carlosmorgan81233 жыл бұрын
Too wrong and dangerous way, please search repair manual first. The arrow in piston top, indicate the exhaust side.
@shadetreeautomotiveenthusi12843 жыл бұрын
I'll remember that for when I have to rebuild the engines on my other lawn equipment. So far, the blower in this video functions just fine, and has been used MANY times for the fall and late summer leaves. Thanks for that information.
@ia69804 ай бұрын
So after running bad gas nd piston got messed up so i changed it and changed cylinder, fuel lines and carb including fuel filter and blower still wont start, i changed carburetor, after running bad fuel it ceased and i couldnt retract recoil starter, but after changing cylinder and piston, i can retract recoil starter but engine wont start. At some point it started few times and then dies real quick. Any help?
@heathwilson25723 жыл бұрын
You should put piston on first and then cylinder
@shadetreeautomotiveenthusi12843 жыл бұрын
Lesson learned
@Grenplen4 жыл бұрын
what the fuck is a jug?
@shadetreeautomotiveenthusi12844 жыл бұрын
Replaceable midsection of the engine. Houses the piston and sits above the crankcase. The thumbnail of this video shows me putting the piston into the jug or midsection of the engine.
@stevenrobley14 жыл бұрын
garbage day and a 100$ piston kit i love it
@johnbev54 жыл бұрын
Nice job! Just got same model that was run on no oil mix. You saved me time on reliving-block from case
@simplyhandy27693 жыл бұрын
Man I baught one for 100$ guy told me str8 fuel only. And low and behold I should have known better!
@happyman53893 жыл бұрын
my carb had the same plastic clip on top too i dont know why
@Jrixi2 жыл бұрын
You said you had to tune the carb? How do you do that? Or can you point me in the right direction?
@shadetreeautomotiveenthusi12842 жыл бұрын
L&H adjustment screws. One's an idle, and one's a high rev air/fuel mix. First play with one and get it to idle, next, go full throttle and get it warmed up, hold it at full throttle, and make an adjustment on the H screw. There's a sweet spot between a lower rev sputter and a high rev zing. Bring the screw to the sputter, and just a small turn to bring it into the high rev. Then let it go back to idle. If it doesn't idle, only adjust the L to bring it back to idle. Then test it again at high rev to make sure it's in the sweet spot just above the high rev sputter. This adjustment varies on temperature and oil to gas ratio. So always try to run the same mixture after your adjustment. This goes for most all 2 strokes.
@Jrixi2 жыл бұрын
@@shadetreeautomotiveenthusi1284 Thanks for the reply and the Video! I'm looking forward to this rebuild.
@johndezsi42503 жыл бұрын
I'm about to do exactly what you did. About a million years ago when I first started with motors engines. My trainer told me to check the oil in a two-stroke snowblower? They all laughed when I couldn't find a dipstick. You can't find the dipstick put the oil in the gas. Enjoyed your tutorial on the Husqvarna.
@sonofthunder.3 жыл бұрын
i have this model, the carb has a low speed adj,after remiving a tiny plug,with a heated pick, or screwdriver,older models, had a high speed adj screw,i found one after searching awhile on ebay,so i could tune the carb better than ,what the epa allows, good video,nice fix,yeah that carb is a universal replacement,
@louismays78102 жыл бұрын
good deal for the price. i paid $540 for mine 3 days ago congrats on rebuild