Husqvarna HU675AWD Mower Self Propell Not Working, Diagnose Idler Pulley Repair, Husky DIY

Diagnose Husqvarna HU675AWD Mower with failed selfpropelled drive. After diagnosing the problem (idler pulleys), we do a step by step removal of bad components. This is a diagnose and dissassembly video. It does not address the drive pulley. But, that pulley pulls straight down and off with an alignment key and keyway.

[@josephrego3811]

Thank you for being so precise on how the belt diagram goes I search all over the KZbin. You the one who the best tutorials thank you.

[@bigjersobservations]

Glad you found it usefull an thank you for the comment

[@scolopede]

"now let's go around top and get those other two screws." I found one of these at a curb, took two oil changes in a day to clear that up, now has a clean carb, works great. But those "two screws", that was driving me nuts, I couldn't figure out why that would come off. Thanks for posting this.

[@bigjersobservations]

Thank you for your comment, and I'm glad you were able to finally get it finished.

[@19surfing]

Great Video Only thing I would stress is TO CHeck if the Bracket holding the pulleys is still attach to lawn mower, My bracket had broken off at the screw point. so of course putting everything back together didn't go so well.

[@bigjersobservations]

Thank you for your comment. Your absolutely right about that bracket.

[@RaulMedina-b3d]

Thanks for posting. I was able to change two of mine today. Thanks for posting. Much appreciated.

[@bigjersobservations]

Glad it helped

[@carlos2044]

Great vid. So my question is I'm having a problem with not being able to pull the cord. It's stuck and i have the exact make and model push mower. Any ideas where to start looking at first? Thanks..

[@bigjersobservations]

Thank you for you comment. Answer: Unfortunately I do not have that mower with me. So other than trying youtube videos you may want to try this link: origin.kohlerenginesparts.com/oemparts/l/koh/61857843855d461d145af844/xt675-2075-husqvarna-parts Once you go to that site click on the page 07 starting Use it as a reference. remove the blower housing, about 3 nuts/screws. remove items 1, 9, and 4 as necessary. check for binding and free play as you go check the engine brake cable releasing check the blade under the deck after disconnecting spark wire/cable I am not a mechanic, just a tinker, but i would use this type of approach.

[@bigjersobservations]

also try the shop manual: resources.kohler.com/power/kohler/enginesUS/pdf/14_690_01_EN.pdf pages: 32 and 33 is a good starting point.

[@andrewgangloff5016]

I removed the main drive pulley and the key came out in two pieces. I am not sure what to do with that or how to get it back in place. I am going to assume I need a new key, but have not found any information on how or where to find one. Any help on where to get parts?

[@Ahoooie]

Great video,ty for making this for us.

[@bigjersobservations]

Thank you for your comment

[@MSmith1182]

Thank you. About to start this same job. Could you give an estimate on total time for project with all pulleys and belt available prior to installation? Cheers

[@bigjersobservations]

I estimate 1.5 hours, it really goes fairly quick.

[@tonygonzalez3477]

Thank you I have the same mod. you help me alot thanks.

[@bigjersobservations]

Glad I could help, Thank you for your commnet

[@mgomez5606]

Did you make part II video. Did not see it in your videos.

[@bigjersobservations]

Thank you for you question. Sorry for the delay, I shot it, but lost the video files, and that is why I show the belt arrangement so prominent in the video, because that is the hardest thing to figure out. I hope that helps

[@mattwedelich347]

Good video 📸😊

[@bigjersobservations]

Thank you. Glad you found it helpful

[@bahramafshar3976]

hi great video instructions , i have almost the same type , except mine has 2 belts , i had to change the belts , it took long time until i get my parts , now i gorgot how to put them back , i can not find single video like my model , dont know why ??? am i the only one has this HU 725 AWD/BBC , with 2 belts ???? please if any one has like mine or has one , if you can make a very clrar step by step video . or send me a link , by the way i have watched all single video on youtube , all they have one belt. 1 is short belt and second one is long like others , please some one helpe me out

[@bigjersobservations]

Thank you for your comment. I am not familiar with your model. However I did a check at the Husquvarna support website and found 12 documents (manuals: owners, and illustrated parts lists, IPL).If you go to that website you may find the document you need with a diagram. The link I used was: www.husqvarna.com/us/search-results/?groups=DOCUMENTS&q=HU++725+AWD%2FBBC+ Good luck with your research.

[@darlenedoden9465]

Still don't find part 2, unfortunately since this is the best video I've found for this

[@bigjersobservations]

Thank you for your comment. I should probably change the title until bercause I still have not made a part two reassembly.

[@giloquendo]

Hi I have the same one but I can't find the model number can you help me please?

[@bigjersobservations]

Thank you for your question. I do not have the mower readily available, however I think at the 35 second point in the video you can see two white decals on the top back of the mower deck, and I believe it is on one of those if you still have those decals. Also if it helps, use the operator and parts manuals downloaded from Husqvarna, and the operator manual says "HU675AWD 961450015. Hope this helps

[@NgaMoore]

I need to know about the corporate how to put back Gill Put back together Put back together I need to know do they have a Spring format from cooperator to the muffler is there a Spring there

[@washinton1020]

WHAT ABOUT THE MAIN ONE YOU DID NOT TOUCH I HAVE THAT ONE THAT IS BAD.

[@bigjersobservations]

Thank you for your comment. Please disreguard my first response to your comment. The "MAIN ONE" you comment on I believe you are talking about the drive pully with the little star embossed on the bottom of it. Once you removed the blade you should be able to pull it down and comes right off depending on rust. Penetrating oil overnight should take care of that. If that star is sheared off then the drive will still work but the blade will stall in medium to heavy grass. Recommend replacing pully with new part. However I have welded a new star and then ground it to fit with dremel. Best of luck

[@gradyhernandez4699]

Just say or show what is needed..not a biography of mower

[@bigjersobservations]

Thank you for your comment