HVAC: How to remove Exhaust Blower wheel | Blower motor removal

Like, Comment, & Subscribe!!!

[@QualityHVACR]

Removing a wheel from a motor can be a pain, nice job! Nice tip with the brake cleaner.

[@HVACRVIDEOS]

great video Joe !

[@DanAnderson_TheMaddestShredder]

Respect My Brother You R a Talented Individual, My Son Actually Is In The Same Buis. Respect Always

[@HVACRNorth]

Thanks for coming bye ......Appreciate it bud... if he needs anything let me know for sure;)...

[@hvacjohnnie]

Very nice Break down. Nice job, I haven’t changed one of those motor yet. Keep it up

[@HVACRNorth]

Thanks bro.

[@rottiev264]

Great video, I’ve had a couple Goodman air handlers where the wheel will not come off the motor shaft. So since the motor was garbage anyway, I took it apart to expose the backend of the shaft. I set a deep socket on the inside of the blower wheel so the front side of the shaft has room to move, and hit the back of the shaft to move it through the wheel. Then flip it over and do the same but with a punch so I don’t mushroom the end. A couple back and forth and it’s free and slides out.

[@HVACRNorth]

thanks bud and exactly lol you got the trick ;)

[@FlyEaglesFly19111]

Good job North.. you can dooooooo it!

[@HVACRNorth]

woo0000

[@TheLuckyman7726]

The blower wheel puller is always good . hasn’t failed me yet

[@TOMSIGHTVLOG]

very nice technique although the socket broke

[@newfoundlanderingallsfamil4084]

Hello thank you for checking out my channel and puppies 🐶 was nice chatting with you also

[@newfoundlanderingallsfamil4084]

Good people good channel good luck shoutout to you

[@HVACRNorth]

Thank you

[@Leenie333]

🤗Happy Midweek, Joe! 💜👍🏽#96

[@HVACRNorth]

hey hey 🤗

[@IHVAC]

Good Info

[@jerryfrigeration]

How do you use the other puller. I have the other one and woul like to know how you use the other puller

[@HVACRNorth]

Email me bud I can help

[@jerryfrigeration]

@@HVACRNorth please what's your email

[@HVACRNorth]

@@jerryfrigeration [e-mail]

[@kangaroogod]

That really blows (breaking your tool) Most times after loosening set screws I put a a crescent wrench on the shaft and hold on 1 hand while alternating turning the wheel back and forth with the other. Usually walks right off

[@HVACRNorth]

I know bud & that particular one was a snap-on 🥺

[@Lizaraga.Famiy.]

Great video , how old was it? N is what makes the motor go bad.

[@HVACRNorth]

Very old, was a public gym early days and was still original lol. Did my own investigation. Bearings are dry, over time the grease gets pushed to the out sides which makes the bearing it self to heat up and eventually fail. Thanks 👍

[@hozerhvac4406]

👍🤙💪

[@HVACRNorth]

How did you know superior lol. I thought I seen you on the dark side earlier, i hope I'm right. We have to get OCREFRIGERATION there as well lol. 👍✋

[@OcRefrig]

been there , done that ! i Like the Sunny side Better !

[@OcRefrig]

Good video ! But , Heres a tip to make the Job whole lot EASIER. Ever since i Learned this tip i have never even needed a Puller anymore. Remove All set screws, Squirt Wd-40 in set screw holes , Spray wd40 all over shaft , sand shaft as usual till shiny , no rust what so ever , THEN Tap Blower wheel Farther onto Shaft EXPOSING A RUST Line That MUST BE REMOVED & When removed Blower Wheel WILL SLIDE OFF Like Butter. No Puller Necessary. Hold Wheel and use a crescent wrench to grab on Flat side of shaft , Squirt Wd-40 , Twist shaft once , whala ! OFF SLIDES WHEEL. WORKS EVERY TIME !

[@HVACRNorth]

I have tried that one by mistake lol on a resi blower, & you are right IT WORKS. Great tip for ALL. Thanks for dropping by👍

[@HVACingMyWay]

OcRefrigeration , Hvac & Electrical Video's. That’s how I do it to works great. I use to hate removing them until my dad showed me that trick now I never have a problem with it.

[@superiorcomfortheatingairl3373]

I have to ask this, when the video was fast forward at different times, was that the time you were cursing 🤬

[@andrewsimon5437]

That type of fan is called a down blast utility fan, correct?

[@HVACRNorth]

Correct 👍

[@xraybravo7180]

Where did you get the first tool ?

[@HVACRNorth]

Online bud. If you need any guidance email me [e-mail] 🤙👍

[@projectme2702]

Where can I buy that tool?

[@HVACRNorth]

Yellow jacket 60590 , SUPCO FBP100. Automotive suppliers have as well for pulley removal. 👍

[@kc00]

Click bait!! Where’s the chipmunk in the video?