"I know a lot of people say I use too much solder but I just like to be sure! It's my company I don't care if I use it and I don't care if my employees use a little too much solder, better than not using enough!" That's how to create a trustworthy company! Do the job right or don't do it at all!
@etherealrose21393 жыл бұрын
As long as you allow for capillary action to actually seal the joint it doesn't matter if you bead extra on the outside seam.
@greendryerlint3 жыл бұрын
I don't do HVAC for a living, but I do feel if you go a little crazy on the solder, it might be kind of unsightly, but it gives the joint more physical strength, which might matter if you have something like an out of balance fan that's vibrating the joint for years. I've certainly seen this in electronics.
@Happyoldfashionfamily3 жыл бұрын
Ha. I had an employee that constantly plugged up cap tubes and service valves doing just that. I do agree a little extra won't hurt but in his case it did.
@greendryerlint3 жыл бұрын
Yeah, maybe don't go THAT crazy with the solder..
@75LS1Vega3 жыл бұрын
Too many people use the ' I do it right because I do it twice' mentality when it comes to work anymore. I would rather use a little extra solder and not have to worry about going back in to fix a leak after you get the unit up and running!!!
@Henchman19773 жыл бұрын
You should have a "My Superheat is a little high" with a graphic of the gauges... It's practically your catchphrase at this point.
@gbuss8143 жыл бұрын
I remember decommissioning mom and pop grocery stores because of the phases out of R-502 and R-12. I seen many owners crying because they could not afford the refrigerant retrofit. I just hope we don't just help the big companies and have some grace for the small independent owners. But I'm not very hopeful. Awesome video!!
@KentuckyReef3 жыл бұрын
I do commercial HVAC service and on a lot of equipment they require the risers to decrease in size for proper velocity/oil return. You have to be very careful. I know most installers don’t take time to read the install manual” but they provide that information for a reason.
@meeder783 жыл бұрын
Nice install! Interesting to see the whole sizing process. And not to forget, I love the 80's inspired synthpop music :-)
@lqueryvg6663 жыл бұрын
At 33:51 - some installers stop there and you can tell that the solder didn't flow as you would think, so when he says "use more solder" and double check everything, he is NOT kidding.....solder is cheap compared to "callouts" on a system you JUST fixed.....great vid - thanks!!!
@winstonwright36133 жыл бұрын
I really love these longer videos where we get to go on the journey with you from finding the problem all the way to fixing it. In this case we even got to watch you replace the equipment. I thought it was a great video!
@TheWilber093 жыл бұрын
Super interesting to see real world usage of the things I am learning in my morning classes right now.
@ThatEMOguy743 жыл бұрын
A little trick I learned for making those cans of a foam last longer dip the straws and the tip of the can in acetone It dissolves the spray foam.
@etherealrose21393 жыл бұрын
"That's monstrous, can't believe how big it is." That's what she said. 😏
@TheSiliconSoul3 жыл бұрын
"I reran it, just outside the back."
@emmaa4273 жыл бұрын
I admire your depth of knowledge....thx for sharing!!
@StrengthCircusDD3 жыл бұрын
Those ecm dual speed motors were terrible a couple of years ago. I had a couple of freezers that chewed through the McMillan motors every 6 weeks. I couldn’t help but think about your drain line in relation to the freeze ups. Here in the mid south we have to install traps on the drains and smoke test them to be sure they aren’t drawing outside air. Very clean install.I like the fact that you used all components that can be locally sourced or likely have on your truck. The cover on the line set looked great. It looked as if your insulation had a woven exterior?
@HVACRVIDEOS3 жыл бұрын
I will discuss the on my livestream this evening 9/13/21 @ 5:PM (pacific) on KZbin , come over and check it out kzbin.info/www/bejne/oKrJgmdvqJd_o5o
@awwsomeeonez208511 ай бұрын
Yeah, I' 've had these issues with the same problem... The kitchen crew keeps going into the walk-in freezer leaving the door open or not fully shutting the door , etc. -- I serviced the hotel every week if not every other day. I kept my morale up by saying to myself job security, and that kept me humble elaxed. I appreciate the POV and Keep up the great work.
@garyhorvath29573 жыл бұрын
Thanks for the video's, I have not done restaurants yet, but it's like riding with my journeyman. I learn so much.
@SOURADEEPBISWAS3 жыл бұрын
After watching your video I understood its end of an era for older smaller sized condenser equipment. Whatsoever, loved your installation of new equipment.
@jasonjohnsonHVAC3 жыл бұрын
Great video. Much different video than you normally put out there. Its nice to see another angle of the trade that most of us don't know or have tons of experience with. While i am familiar with load calcs for comfort cooling. I have zero experience with sizing refrigeration equipment and what goes into sizing it and all your components correctly. As usual......top quality information and work. Thanks for what you do for the trade Chris.
@falloutguy88783 жыл бұрын
Hi Chris thank you for another great video keep safe dude plus I hope you get some rest bite away from this condenser now hopefully you have fixed it nice one 👍
@DocNo273 жыл бұрын
Wow - I can see why you like that Russel equipment - the way the wiring was routed inside, zip tied and done with care - what a difference from a lot of the other units you work on. Even though it's taller, won't that single thickness condenser theoretically be easier to clean? Also you think Russel went to single width because of that extra loop at the bottom from the receiver?
@Thermoelectric73 жыл бұрын
Single row might help keep the head pressure lower as well, as it all gets nice cool ambient air.
@robertlowrey54852 жыл бұрын
New favorite channel. Thanks for all you do man.
@fatsuperman5556 Жыл бұрын
An objective definition of a "perfect" install is one where the customer is happy, the company is happy and the system performs as or better than designed. Everyone has an opinion about what they would've done. It's irrelevant outside of suggestions you may or may not want to use later. Your install there looks better than 95% of what I see in Houston and I'd bet solid money it certainly performs better. Great work!
@aswiendharmawan48693 жыл бұрын
Hi, always wait for your amazing videos, watching from Indonesia... 🙏🏻
@tbelding3 жыл бұрын
No reply required - one thing you might look into is one of the two part PE (urethane) expanding foams, rather than using the "good stuff" canned foams. It's often a bit better at handling temperature and humidity extremes. It may be too difficult to deal with for the small areas upon which you're working, but I thought I'd toss it out.
@854XTOY3 жыл бұрын
Aw that little lizard was a handsome young man
@sherwinalvarez73653 жыл бұрын
Great video. I have always wondered how they pick equipment. I wish you had showed about wiring the relay for those fan motors. I know most of you guys know but I'm still in the process of getting comfortable with electric and retro wiring. As always still a great lesson. You dont know how many teachers and supervisors refer new techs to you videos because they help everyone get to where they want to be.
@frankmontefusco60163 жыл бұрын
Great video!! Love how you showed the sized the components Keep up the good work!!
@mark3513 жыл бұрын
That little lizard wants to be Chris' new apprentice.
@guygfm42433 жыл бұрын
Good video kept my attention all the way through. Thanks for sharing
@markcaldwell12453 жыл бұрын
What no Trane manual with long forms and graphs, lol. Great introduction into a few of the things to consider when sizing equipment. Also gives techs a better understanding of things to consider on hard to diagnose jobs. Great job.
@davidefinland68863 жыл бұрын
CHRIS, add to the title "- AWEF calculation". This video is a hands-on reference.
@enifyako2 жыл бұрын
The stuff at the end got my like. You’re great, Chris.
@davidu47583 жыл бұрын
Heh, heh...Lizard wants to sell Chris some GEICO insurance.
@joshuapalmer2483 жыл бұрын
Awesome video Chris!
@HVACRVIDEOS3 жыл бұрын
Thanks! I will be going live on KZbin this evening 9/13/21 @ 5:PM (pacific) to discuss my recent uploads and answer questions from emails, the live chat and KZbin comments. Come over and check it out kzbin.info/www/bejne/oKrJgmdvqJd_o5o
@jovicatovarlaza93393 жыл бұрын
I only use Trenton here in Clearwater Florida. Already pre assembled with everything and it has the 2 speed “smart tech” motors, honestly haven’t had any issues with it.
@achannelwithnopurpose19773 жыл бұрын
Gotta love hammered coils and managers who keep calling for the same problems.
@nsaglian3 жыл бұрын
Love that Brazing Montage music!
@vincentramirez83033 жыл бұрын
Dude no such thing as, perfect. But your dam close to it ,with your work..thank you Sir..
@cityscene1213 жыл бұрын
If 'Refrigeration' is your game then these compliance mandates are essential to see, in the real world, as demonstrated here. Thank you for sharing what obviously took effort and time to investigate, but not only that also the explanations pertaining to 'Why and How' these changes affect the system to acquire the desired outcome. Great knowledge 'Download'. Great job!
@manuelherreros4609Ай бұрын
Nice work right there! Keep it up 👍
@Riyame3 жыл бұрын
28:53 Yup, $1 worth of solder is cheaper than trying to find that pinhole leak that you missed initially, or coming back a week later on an emergency call after that joint that looked fine fails in the middle of the night.
@joshc85993 жыл бұрын
28:50 i like watching you solder. you make soldering look like child's play. unfortunately when i do it, it looks like a child did it. lol
@LMSILVIA3 жыл бұрын
That brazing inside the box oohh so nice, i was loving life last week brazing inside a PVC lined WIF ...
@bluedogdataelectrical63033 жыл бұрын
Great video Chris.. thank you
@uxwbill3 жыл бұрын
This was really informative! Having a run-through like this would have been invaluable in my commercial/refrigeration classes. (I don't really have any intention of ever doing commercial/refrigeration work, but knowledge is knowledge.) I am, however, shocked to hear that you're not getting into the professional painting business! :-P
@CHOMAHOMA2 жыл бұрын
This is a great install to me. Nice work.
@realestateservicessaleshea993 жыл бұрын
It's almost unbelievable that people don't use nitrogen while brazing, nice flow that's how it's supposed to look. I see tubers that get it to start flowing then they get scared and take the heat away to early. (They worry about the names of the tips they use 😅) Thanks for the video! 🥃🥃🍺🍺🍺🍿🏌🏻♀️ Stay safe. Retired (werk'n)keyboard super tech. Wear your safety glasses.
@HVACRDUDE3 жыл бұрын
It doesn't matter bro...there's a drier
@realestateservicessaleshea993 жыл бұрын
@@HVACRDUDE yeah but...
@HVACRVIDEOS3 жыл бұрын
I will discuss the on my livestream this evening 9/13/21 @ 5:PM (pacific) on KZbin , come over and check it out kzbin.info/www/bejne/oKrJgmdvqJd_o5o
@JonathanB-y8z10 күн бұрын
The lizard is going to be famous 😂
@michealthaarchangel50882 жыл бұрын
That lizard wanted to tell you about Geico insurance 😆😄😁🤣😂😅
@arotechmechanicalhvacr11583 жыл бұрын
I do the same Chris I use a little more brazing rod the guys that use just enough run risk of getting a leak at some point, also sick video!! Show em how it’s done!
@idontneedaname853 жыл бұрын
Good morning! thanks for the vid
@thesilentonevictor3 жыл бұрын
Great information Chris 👍
@SupremeRuleroftheWorld3 жыл бұрын
28:50 there is no such thing as too much solder. and you have to cool it, it softens the copper and prevents cracks and holes over time. pro tip: please ditch the wire nuts, use wago 221. wire nuts are borderline illegal in europe already. wago is also a lot cleaner and better over time by not twisting and mangling the wires making repairs in the future a lot simper and faster. never forget: the next guy is probably you.
@arnobruynen60733 жыл бұрын
American electrical standards and general practices are just shit in general. They clearly prefer cheap and easy over safety and durability. Not just wire nuts but other stuff I frequently see on this channel like those terminal boards, flexible metal conduit, disconnects with non insulated contacts, leaving wires dangling and zip tying them together instead of running them through tubes and trays where they can't rub out etc...
@89dhvac3 жыл бұрын
I disagree. When used properly, wire nuts provide a much more secure connection with less resistance. Wago style connectors are not nearly as secure and therefore create the chance of increasing resistance and heat. They may be fine fire low voltage and low current applications like led lighting, but should not be used on anything heavy duty. Just as an aside, it makes no difference what Europe does. They use the metric system and traffic circles smh lol
@SupremeRuleroftheWorld3 жыл бұрын
@@89dhvac wago's are actually more secure over time (they dont loosen up giving dodgy connections) and dont care about the wire type and can handle overload situations equally well or better. when dealing with ld and corroded wire it will hold up much better then wire nuts. this has been tested time and time again. your point of view seems to be more about personal opinion than fact based. And "when used properly" is exactly the problem. Nobody does use them as they should.
@laskahvac6663 жыл бұрын
@@SupremeRuleroftheWorld I use Wagos alot especially on communicating systems and low voltage, however wire nuts still have their place and purpose. Find me a Wago that will work on 6g wire. By far the best connection/connector for larger gauge in my opinion is a Polaris connector but wire nuts (when properly used) will work just as well as a Wago. If you're putting Wagos on corroded wire, I don't think you should be giving advice about anything electrical.
@SupremeRuleroftheWorld3 жыл бұрын
@@laskahvac666 i am not saying you can put wagos or any connector on corroded wires, its just that they deal a lot better with corrosion (due to time, elements, heat) then wire nuts do. and unlike wire nuts they are insensitive to viberation from machines. and its not personal opinon, it is fact. and the 221 does not go to 6awg, it peaks at 10. beyond that you should not even consider 221's, wire nuts or whatever, the only thing solid enough (especially outdoors) is bolted terminal blocks and crimped connectors. you show me a wire nut that has been used on a 6awg wire and been on a roof for 5 years in the desert and i will show you a wire nut that has been utterly destroyed from the resistive heat it generated. for proper high current connections you always use proper sized crimped and heat shrinked connectors. if you are making more reasonable sized connections that are sensitive to the elements like sensor wires you use a wago gelbox for example.
@terminator7613 жыл бұрын
Dont be so hard with yourself on installs you mainly seen to do is service . Those" instagram people " do installs all year arround so thats why it might look better. Stick with what your good at!
@antoniofabro37593 жыл бұрын
Thats a perfect install keep it up chris!! 🤙
@asplodec3 жыл бұрын
Channel subtitle: 'The frustrated HVACR service guy'
@HVACRVIDEOS3 жыл бұрын
I will discuss the on my livestream this evening 9/13/21 @ 5:PM (pacific) on KZbin , come over and check it out kzbin.info/www/bejne/oKrJgmdvqJd_o5o
@jefferygrady31813 жыл бұрын
You are busy now because you and your employees do high quality work and that is hard to find today with all the hacks out there!
@kennethconnors53163 жыл бұрын
Sporlan rocks with the tech stuff / great to back you up with ..
@Ted_E_Bear3 жыл бұрын
Thanks Chris !
@tmacgee12343 жыл бұрын
That was cool. Been waiting for that load calculation.
@infidellic3 жыл бұрын
39:29 lovely view of the frost(?) melting/sublimating on the pipe lower left
@Eddy633 жыл бұрын
Professional job as usual , very neat looking ... Thx for the vid ...
@johnwalker8903 жыл бұрын
Good job Chris.
@andrewrees66183 жыл бұрын
1.love the music while you're soldering. 2. Love it when you talk about dealing with customers and your frustrations. It's good to hear stories from other guys on this topic. 3.love how you focus on quality and the big picture. The consummate professional. Keep up the good work.
@HVACRVIDEOS3 жыл бұрын
I will discuss the on my livestream this evening 9/13/21 @ 5:PM (pacific) on KZbin , come over and check it out kzbin.info/www/bejne/oKrJgmdvqJd_o5o
@jessienascar8778 Жыл бұрын
Good job man krep the video coming
@etherealrose21393 жыл бұрын
Watching while drinking my coffee before I install a mini split. Still dark on the west coast.
@graywolf26943 жыл бұрын
im honestly surprised HVACR equipment doesn't have more computer control in it, transport refrigeration is only controlled by computers, it can control discharge pressure by reducing suction pressure with electronic valve
@aaronward75263 жыл бұрын
The small restaurants won't have these. They need simple and cheap controls. You getinto larger commercial refrigeration and HVAC and they are all computer controlled.
@shifter82073 жыл бұрын
Thanks for this type of video i loved learning how to size this stuff!
@JjMn10003 жыл бұрын
Cool video!
@lukeeisenberger48723 жыл бұрын
Could you do a van and tool bag tour with all your tools and equipment??
@firestorm92093 жыл бұрын
Great video again waited for it to come up even if I have to calculate the time because mine is CEST. I like to watch KZbin more than other streaming platforms and stuff because you can watch tons of stuff you like to see.
@pmgodfrey3 жыл бұрын
0:04 -- He just wants you to save 15% in 15 minutes on your car insurance.
@BenCos20183 жыл бұрын
Lmao
@bondjames2205 Жыл бұрын
Had same issues with restaurants in downtown Cleveland. Walk in freezer packed all the way from the evaporator to the door and the only time they would call is towards the end of the day when they were closing. " Frustrating "
@EoRdE63 жыл бұрын
That's a serious sized receiver, I know nothing about hvacr but that seems massive
@HappilyHomicidalHooligan3 жыл бұрын
One way to get your customers to stop causing frivolous defrost calls is to simply tell them that after call number 3 that's caused by your people propping the doors open, I'll start charging you an Irritation Tax (AKA Asshole Tax) of $50.00 for the first call after the warning and increasing by $50.00 for each additional frivolous call after that ($100.00 for call 2, $150.00 for call 3 etc.)... Wanna bet you never get another call caused by the cooks propping the doors open? Heck, I'd bet you'd be able to hear the Manager scream at the staff from 5 Counties away...
@johnbroski19933 жыл бұрын
Flat roof penetrations you should use a Chem Link E curb. I've used them for conduit penetrations for pvc and they don't leak if you do them right.
@plg22083 жыл бұрын
Thx for sharing
@elijahtalbot52883 жыл бұрын
Nice video
@ICountFrom03 жыл бұрын
This is very much back to the start of the channel, something that your staff will probably check while out on a job, but is still fascinating (though completely useless) for the rest of the folks to know.
@sherwinalvarez73653 жыл бұрын
Idk who the rest are but the HVAC/R geeks love this kind of info.
@335alien3353 жыл бұрын
So what was wrong with the existing equipment? And what will replacing it do if there is a constant stream of humid air going in?
@HVACRVIDEOS3 жыл бұрын
I will discuss the on my livestream this evening 9/13/21 @ 5:PM (pacific) on KZbin , come over and check it out kzbin.info/www/bejne/oKrJgmdvqJd_o5o
@barkere513 жыл бұрын
I love it when he is like this equipment is in bad shape. I have a walk-in cooler that is 38 years old...and it has the original evaporator and when I bring up the wall caving in no one is interested in replacing it. One day it will collapse on an employee and I doubt we would replace it even then.
@MrBlizzy232 жыл бұрын
you may want to steer towards R-449 .....it's a few bucks cheaper per llb. just a thought. both 448/449 are viable refrigerant solutions for the incumbent 404 /low temp apps. A lower GWP @ -51 boiling point could save you a few bucks on Retro's ! great video btw!
@gatoguevara713 жыл бұрын
Good job 👏 👍
@mummabear013 жыл бұрын
Hey Chris, watch that first step... it's a doozy!
@maloillest Жыл бұрын
Your Beverly Hills cop music 📈😂frfr
@michaelgraziano80383 жыл бұрын
Chris: "This little lizard just came up to say what up?" Lizard: "Yo, are you Fight, Food, Fuck, or Flee?"
@AndreasDelleske3 жыл бұрын
Chris: Fan, Fuse, Fumble, Fahrenheit, Fluids, Frost and frustration. Just freeze, fellow. Family fine?
@michaelgraziano80383 жыл бұрын
@@AndreasDelleske Hey! It's only 4 Fs! If you confuse the lizard's tiny brain it will have no choice but to crap on you in self-defense!
@torinbrown8196 Жыл бұрын
Yr old vid and my apologies for the late watch/ reply. With that said how about those wooden 4" by 4"s that weren't somehow fastened in place? You had mentioned tweakers earlier so I go immediately to thinking they can kick them out from under the skid.
@jimmynoneya25842 жыл бұрын
What is the best way to defrost that ice cube you had going on there? What did you use hot water? Or a heat gun?
@throttlebottle59063 жыл бұрын
hopefully you kept the line-set from touching the galvanized steel, because electrolysis is nasty between the two metals :)
@laughingwolf87113 жыл бұрын
Love the lizard 🦎
@peterhansen82163 жыл бұрын
You can order replacement outside trim from everidge(ics).
@garypoplin45995 ай бұрын
You briefly mentioned in this video about clogged screens causing oil to be trapped inside the suction line accumulators. I haven’t been able to find any information about that anywhere. Can you explain how that works? What’s actually happening in the system to cause this? Still learning by the seat of my pants. I’m working on a walk-in right now that had an unexpected spewing of oil out of the low side valve on its condensing unit when releasing nitrogen after a pressure test.
@stevemcknelly50363 жыл бұрын
Pssh, always going to be someone in the comments who tries to backseat tech. Like you said, your company, you drive. A little more solder might save you time and trouble of a visit to find a leak in the future. Love the bit with the lizard!
@kittyztigerz3 жыл бұрын
that a dragon lizards normal find them in hotter area i have ton of gecko in my area lol you are right about kindness it mean a lot to anyone
@Happyoldfashionfamily3 жыл бұрын
My second visit would have been, you are getting a new grasslin defrost timer weather you like it or not. I hate these kind of calls.
@special_k-hvac3 жыл бұрын
As long as you're charging them no problem going on a service call
@analogmoz3 жыл бұрын
Around 34:30 - these brazing montages are reminding me of Beverly Hills Cop. Public-domain Jan Hammer jams for all.
@laskahvac6663 жыл бұрын
Thank god Chris didn't put a banana in the suction line
@analogmoz3 жыл бұрын
With the original 1-1/8" suction line a banana _could_ fit, so Chris, being the practical man he is, sized it down to 7/8". Smart man.
@HVACRVIDEOS3 жыл бұрын
Ain't gonna fall for no banana in my tailpipe!
@854XTOY3 жыл бұрын
I prefer eggplants in my tailpipe
@samsscia3 жыл бұрын
Great Video as usual Chris, what brand of watch is that?
@HVACRVIDEOS3 жыл бұрын
Samsung galaxy watch 3 with a supcase watch band, I will be going live on KZbin this evening 9/13/21 @ 5:PM (pacific) to discuss my recent uploads and answer questions from emails, the live chat and KZbin comments. Come over and check it out kzbin.info/www/bejne/oKrJgmdvqJd_o5o
@ralphwoodard6093 жыл бұрын
Don’t kill telling the customers with a really, really need to know the time here. Remember stupid is as stupid does. And on the ones that you have to keep going back to keep charging them a premium price for your service. Maybe they’ll learn.
@ReliableHVACR3 жыл бұрын
Nice 👏🏽
@MariosACandRefrigeration3 жыл бұрын
loved the vid,what was the pressure on that by pass valve on the condenser ?