This is the molded diamond Hydro Turf with the 3m self adhesive. Hydro Turf custom install on a 14 foot, 200hp mini jet boat I built. I didn't find any how to videos that fit what I was doing so I decided to make one myself.
Пікірлер: 45
@regconrad778310 ай бұрын
Nice work I did my river boat awesome stuff sharp Olfa knife keep it square to line your cutting old carpet layer trick nice finish
@stephenknight1325 Жыл бұрын
Sick boat and turf job
@doodletime16495 жыл бұрын
Bad Ass boat. Perfect set-up multi-fun-fish-friends. Got me thinking on my new project.
@bradcampbell98555 жыл бұрын
Great video - very helpful!
@KrisDeVo5 жыл бұрын
Thanks!
@toddruthruff8342 жыл бұрын
Kris... great video! I realize it is several years old now, but still one of the best on foam decking install. What did you use to round your corners? Was it freehand or did you use something to get them consistent? Thank you!
@pawcrawlowens87302 жыл бұрын
Nice boat
@yodaveskii1204 жыл бұрын
great vid! Very descriptive and very well put together! def a follow here
@KrisDeVo4 жыл бұрын
Thanks!
@bruciorediculo4 жыл бұрын
Hi there brother, great work! I have an aluminium diamond plated deck and I am a bit uncertain about the hydro turf adhering to it completely. have you ever stuck it to checker plate? should I base coat it with marine adhesive ? cheers
@KrisDeVo4 жыл бұрын
If you had a grinder with a flap wheel or 36grit sanding pad you could buzz the diamonds right off pretty quickly. I don't know how it would stick right over them. The adhesive back is super sticky though. Maybe try a section and see what it looks like before you do the whole thing. If water gets under there is will pull after a while. Good luck!
@bruciorediculo4 жыл бұрын
@@KrisDeVo I fish in salt water and that's what I am worried about, water going under and corrode it.
@KrisDeVo4 жыл бұрын
@@bruciorediculo Might want to grind the diamonds down and/or throw some bottom paint on it to keep from the salt.
@elmeradams87814 жыл бұрын
I think I missed the answer on the film, but What material did you use for the template? Where do you get those strips?
@KrisDeVo4 жыл бұрын
This is template material from a local finish carpentry supply. I think you can find it online. Poster board or cardboard work too. Just cut with straight edge.
@billballeza377 Жыл бұрын
Looks like a factory job!
@KrisDeVo Жыл бұрын
Thank you!
@MrAjtellier Жыл бұрын
How about a design overview and some pictures of the engine bay and plumbing
@KrisDeVo Жыл бұрын
Full build on Alaska Mini Boats page on facebook
@JorDangerous9075 жыл бұрын
How can I join the mini club?! I live in A-town and just purchased a Hewescraft 18’ River Runner w/Rotax Supercharged 250. Great videos and a AMAZING boat, good job! I want one!! How much?!?!
@KrisDeVo5 жыл бұрын
Thanks man! Check out the Facebook group, Alaska Mini Boats. Join the club lol. That sounds like a pretty sweet boat! Well it took me forever to build this boat so not for sale. Maybe someday Ill build another.
@jgiajnorio5 жыл бұрын
Awesome boat. What are you running for lights on it?
@KrisDeVo5 жыл бұрын
Thanks! Running 2 sets of the Rigid Industries D Series Pro floods up front and SR-M Flush Mount Diffused on the rear of the swimdeck. Haven't used them yet because we have 20 hours of sunlight most of the summer. Fall is almost here thought so we will see how they work on the water.
@jgiajnorio5 жыл бұрын
Kris DeVo gonna have to check them out online. Thanks. Boat looks awesome! Get us some videos with it lit up when you get the chance
@KrisDeVo5 жыл бұрын
Thanks will do!
@taz-man6137 Жыл бұрын
I also am looking for the right boat . forwarding your video's too my Brother. Looks like a nice good all around boat. Great for Hunting.canadian old boy. I have new 20' jet boat but would like a little tougher boat.. How do I get my hands on two.?
@KrisDeVo Жыл бұрын
I built this, look at FireFish, MotoJet or Bratt
@leadingedgetec15664 жыл бұрын
Great Vid. How did the Hydro Turf hold up?? It's been a year, does it last/ work / would you use it again?
@KrisDeVo4 жыл бұрын
Thanks! Its been great and has held up really well. I would definitely use it again.
@KiDSkyliinee2 жыл бұрын
How can I purchase a similar boat like this! Perfect!!
@KrisDeVo2 жыл бұрын
I built this one. Firefish, Brattjet and MotoJet all make a boat like this one. Thanks!
@chadengel45033 жыл бұрын
How much to weld up a 12 . And . Power triple 3 center . I’m the center ? . 16 thousand?
@deshkavb Жыл бұрын
Where can I get a boat like the one you have?
@brennanamann70293 жыл бұрын
Hey kris what kind of flooring is that?
@KrisDeVo3 жыл бұрын
We made the floor out of 1/2 baltic birch plywood. I want to say it was 9 ply or so. Then a 2 part epoxy primer and then a rubberized coating. Its held up good but now starting to show some signs of wear.
@19ADAM803 жыл бұрын
Looks good man, come by and help me do some on mine 👍🏼
@YoboiDreadz252 жыл бұрын
Where did you get the boat from
@KrisDeVo2 жыл бұрын
Built it
@YoboiDreadz252 жыл бұрын
Plans please...
@MrAjtellier Жыл бұрын
What hull is that?
@KrisDeVo Жыл бұрын
A buddy and I built one each. Our own design, no plans. Look at fire fish or bratt for a center console mini
@MrAjtellier Жыл бұрын
@@KrisDeVo good on ya for doing that yourself. I really like the open bow style but will go with the walk through window apposed to the center console.