Hydrogen/Oxygen Generator Clean-out + Rebuild

[@Cyparagon]

Great walkthrough! But... 5 neutral plates means 6 gaps. 2.3V between each plate, yes?

[@carsandwater]

You're right! My mistake, thanks for catching that :)

[@moopoo8841]

+carsandwater do a face reveal

[@gurp8051]

he has videos with his face in them

[@gurp8051]

+TexasSmoking Jesus that was the fastest homophobic response I've ever seen for a KZbin comment, that was literally less than a minute

[@piranha031091]

+joyfullalmonds Now let's talk about religion and make parallels involving the nazis...

[@Inventive101]

Good job, nicely done. I like to see so many people doing hydrogen tests. I also made a few hydrogen generators, the problem is that I don't have much time for that. good video, i love hydrogen ❤️👍🏼

[@lasperipeciasdedannita4335]

Woooow!!! is incredible and amazing, congratulaciones friend, saludos desde cuautla México!

[@squishy312]

I've been waiting for years... for the build... but the build/rebuild is good enough!

[@kiefac]

What are those pops when you were melting the nail?

[@Ubernator]

Called a flashback, all the hydrogen in line line is exploding, thats why we have the bubbler. If there was nothing stopping the hydrogen from flashing back into the main container it would blow it self up.

[@TorneraFoda]

popcorn

[@darrellw82]

sounds like electrical arcs

[@max13239]

I dont think these are "full" flashbacks though(probably just inside the torch) since a flashback all the way to the bubbler would make your ears ring and probably blow some tubes off their connections.

[@hudsonball4702]

It's impurities in the steel nail. The nails had a little bit a rust on it so it was probably the small amounts of Iron-Oxide (rust) that was popping

[@DoRC]

Im sure this is a stupid question but what is the purpose of the neutral plates on the system?

[@DoRC]

Nevermind. They are used as votage dividers..

[@pir869]

each side of the neutral plates become opposite polarity ,the further away from one polarity you go,the more closer to the other polarity it becomes,it gives in essence more little + and - cells,from the most negative end each neutral plate face will become negative or positive,so one face of a neutral plate will be more negative or positive than the other side of the same plate -,+-,+-,+-,+ this would be negative supply at one end then three neutral plates then the positive supply at the far end,as Do R/C! says,voltage dividers,they even out and share the potential(voltage).

[@ramaswamyvenkatesh7639]

Excellently made and nicely videographed ! congrats !

[@cachhomevideo1546]

Beautiful video I like your project thank you for sharing

[@jmkyarrow]

sometimes I think this channel could pass off as ASMR

[@Inventive101]

👍🏼

[@sc0tte1-416]

How much current does a setup like this take? Could you run a unit like this in a car off an alternator and inject it into the intake so it would actually give you a positive result in energy used vs created?

[@bobbob6698]

I think this is really cool! You definitely have my support

[@Kuberniccus]

I wanna ask if you have fire arrestor or any kind of protection ?

[@kalleklp7291]

The residue on the plates is due to the use of brass bolts is simply made a galvanic reaction (the chemical added will support this further). Use stainless steel in all parts and get rid of residue + rust/oxidation. Btw..a flame arrestor would be a must-have safety feature. I almost wanted to say "Happy new year" as you melted the nail.. You can fabricate one by yourself a tube and some stainless steel wool is all it takes to be safe. Nice generator setup.

[@jesusmartinez5587]

I have a question, does the generador heats up fast? Or for how long it can be running? Awesome vídeo.

[@markjulius2006]

Nice video. Where did you get the white plastic material?

[@MrItsthething]

2:18 Be careful grinding that. It's possible that the stainless can create some chromates which are strongly carcinogenic.

[@pedrohiguita843]

Good afternoon, your generator is magnificent, what possibility is there to have detailed information to mount the system in the kitchen to replace the gas

[@k.r.roofingco.1793]

are the plate sizes and thicknesses critical? What are the dimensions you used?

[@thomasclemensen1195]

Hello. Thats awesome!👍 Can i ask, why the neutral plates? Whats the purpose of these?. Best regards, T

[@evanyoung3160]

What purpose do the neutral plates serve? do they just add space for the water to build up in or do they do something else?

[@guitarman_3693]

they add volume.. for more water

[@tigranohanyan3321]

Have you tried to weld aluminum? Is it ok to use it for aluminum welding?

[@practalsol]

Are all the plates connected to the system ?

[@CanDoo321]

While melting the nail are the Sparks from the zinc in the nail metal?

[@hudsonball4702]

I think it's rust. Iron-Oxide (rust) has O2 in it and O2 will explode if exposed to an open flame.

[@jasonluke6364]

i agree, it's rust. Similar to a thermite reaction

[@tigranohanyan3321]

Have you tried to weld some metalls with it? Is it good to use it for aluminum or steel welding?

[@petergoestohollywood382]

Tigran Ohanyan *brazing

[@sanmartin2853]

felicidades!!! cuanto voltage le aplicaste y cuantos ampers!!!

[@adilhakim7231]

Hello, great job, you are the best, Tell me, What voltage and amperage do you use?

[@andreifustos2160]

hi! what thickness are the gasket and steel??

[@MathiasMTA11]

how well will it function with normal tap water ? Compared to your solution.

[@Mr.Unacceptable]

Distilled water doesn't conduct. It's the minerals and impurities that make water conductive. He's just using the least corrosive means to make the water it's most conductive. Could use salt water but it creates corrosion. It all depends on what your tap water has in it. More than likely you have hard water that will work just fine or even better but then you have the corrosion and calcium scale build up on the plates.

[@MathiasMTA11]

so it will just have to be cleaned and have som parts swapped out more often.

[@JoeyBartlett]

Probably not as well due to the extra unknown-containments that he can't possibly account for. Adding a verified amount of a substance would allow him to produce Hydrogen and Oxygen at a rate he could control, unlike with tap water which can change time to time. :)

[@locouk]

It would be OK at first but soon clog up with contaminants and get very dirty very quickly.

[@hammobiking8911]

+Joey Bartlett انت في قرقر كتير اني بورلي

[@MiguelGomez-ny1cn]

I have seen many generators, but could you tell me what dimensions the cells have and what voltage you supply to obtain such a large quantity of hydrogen?

[@YourWhysun]

Satisfying to see it cleaned. Very Satisfying.

[@Racewayelko]

A suggestion, use a striker for lighting the flame, I have seen people use small lighters to fire up torches before and the lighter blow up in their hand because the flame ran down into the fuel, or the flame melted a hole in the lighter.

[@CliffMendes]

Hi Sir Can you please let me know the voltage and ampherage you have used for power supply and the size and thickness you have used for the plates.

[@mikewalsh511]

The plates are too smooth. They should be crosshatched with large grit sandpaper to enhance the production.

[@elettronicaemotori]

Ciao ottimo video. Posso chiedere perchè è meglio usare delle placche neutre anziche polarizzarle tutte? Grazie

[@locouk]

Can you buy "Brown gas" or do you have to buy the hydrogen and oxygen separately?

[@rocketman221projects]

No, you can't buy it. If you try to store it, all you are doing is making a bomb.

[@screengames5307]

+rocketman221projects You probably just got placed on a government watch list

[@patrickscodellaro2047]

That's a neat generator! How long can you run that generator for till you need to fill it up again? And do you know what temperature the generator operates at?

[@dogboy0912]

How often do you need to rebuild them?

[@TheMrSeagull]

All that gunk on the plates, is that just from impurities from the water?

[@hho-generator]

Excellent works, Very good.

[@EthanCGamer]

That audio was amazing, keep it up!

[@buyco5513]

How long does it take to make it in that state?

[@melvinhernandez5074]

Don't. Be. Afraid. Continue. CONTINUE. DOING. THIS. PRESIDENT. WILL. HELP. YOU. YOU WILL. NOT BE. FREEZE ON. THE. WINTER BECAUSE LOSE OF. POWER. GOD BLESS. AMERICA. IN. GOD. WE. TRUST. ON. PEOPLE. LIKE. YOU. PUERTO. RICO. SAN JUAN.

[@zanemaingot9690]

Wow very helpful! How much power do you supply through it?

[@HapitokP]

I remember a long time ago that carsandwater talked about finally showing us the set up of his Hydrogen/Oxygen Generator so he could clean it.

[@scagetman]

i use sparkle toilet bowl cleaner, cleans that brown goop off fast

[@supallama6254]

Where did you purchase the nozzle at the end?

[@beaugaskell2096]

I'm curious as to what this style of drycell hho generator is capable of yielding, and at what voltage & amperage level? Also, is this solely the only type of application you use this generator for?

[@kalleklp7291]

Very well made HHO generator. Mine is way smaller but longer though to keep the production rate up while still fitting in an old toolbox.

[@xandon24]

Today I learned that nails are actually sparklers in disguise.

[@CoolStreamT]

What's the thickness of the PVC liner do you use? I think I saw it. Its 40 mil pvc liner from Homedepot, great!

[@tudy4x4]

WOW !! you are the best man.!

[@hb-greenvietnam8361]

where u buy the plastic fittings ??

[@jeksdad5979]

Do you really need the gasket on the last plate next to the non conductive end cap?

[@kirkc9643]

Only if you don't want it to leak

[@Tuathadana]

Do you have to replace the metal that causes oxidation?

[@michaelarcher9201]

This (HIPER-VOLTIC-HHO) reactor can be serviced while running. Close lower valve remove lower reservoir empty AND replace. Open valve add (HV) premix to upper resivour, check again in 60 hours repeat if needed

[@davelawson2564]

what is HV ?

[@michaelarcher9201]

@@davelawson2564 HIPER voltic=purest balanced mixture of hydrogen 2 oxygen 1 that can be made on demand

[@davelawson2564]

@@michaelarcher9201 Obvious question . what is cost of power for generating 1 kg of this mixture ?

[@martilloestelar2082]

Muy bueno tu video desde Chile muchas gracias

[@MrLuccckas]

sounds good, but water reserve will finish more fast than petrol. We need make something diferent for extract the HHO.

[@Thefeelingofthebeautifulnature]

Like what ?

[@MrLuccckas]

@@Thefeelingofthebeautifulnature oil/petroleum**

[@joemarsamson1380]

Question master. Can i compress the gas to a tank and use it later?

[@brianatkinson4484]

No It will explode

[@guitarman_3693]

have you ever heard of the hindingburg blimp... ???

[@Ub3rGam3rz]

What power supply are you using?

[@alovsathuseynov6124]

Hello.I want to ask about your alkaline electrolyzer?Operating voltage? How much electricity is required to produce 1 M3 of hydrogen? Thank you.

[@girrrrrrr2]

I've been waiting for this for so long.

[@enriquemora8171]

Excelente vìdeo , dos pregunta te marca alguna resistencia la celda de positivo a negativo y que espesor tienen los separadores entre las placas , gracias por compartir

[@ogormor]

hi, the power that you use is 50 V 15 amps or 50 amps 15 V???

[@Azathoth43]

Probably a dumb question but could you weld with this?

[@Geekio6613]

I don't really know a lot about this, but at a guess I'd say you probably could, but it wouldn't be the most efficient kind of torch to use. But again, I don't really know.

[@W3flyh1gh2]

I would say you could do some serious brazing! It melted a nail and cut that metal! I would like detailed plans on this.

[@hannelmahinay6288]

next time bro try to focus on the camera the outcome gas results... i saw only water bubbling didn't saw the ouput gas... anyway so amazing bro you did and excellent job... I would like to ask you if i could convert this gas into cooking gas just like gas stove?

[@danijellukic2196]

Do you put something like water betwen these plates or what ??? i don't understand how it works ..

[@joshua-the-seer8494]

Where/how can I get the gaskets that serve as spacers? Can they be custom-fitted?

[@frabert]

What purpose does the safety bubbler serve?

[@guitarman_3693]

it prevents the flame from running back up the tube, if a flame reached the generator , you would have a dangerous explosion.

[@dagandreassen8446]

You have your holes at same place so your plates can't create so much that way. It's better to have first plate 2-3 holes at the bottom and next plate 3 holes on left side, next 3 holes on right side etc until last plate where the exit is and have 3-4 holes at top to get best effect out of everything. I use 22 plates, size 150mm x 150mm and gives me plenty of HHO.

[@jsmith5052]

That's a really awesome design

[@juancarlossandoval2560]

hi, a question is why many neutral plates?

[@mattbentley8958]

To achieve the 1.5 to 3v between plates which is the most efficient voltage range.

[@spicyfrank1]

May I ask how you got your experience with these types of machinery?

[@Jofoyo]

Probably went to a college. Or just researched online.

[@Kingololz]

"probably went to college" is a pretty vague answer. Did he get a degree in an engineering based field? a Science field? Is he self-taught? These are some things that would be nice to know.

[@ipoint01]

you probably explained this in a previous video, but how do the plates stay immersed in water? most models ive seen built involve the plates being in a tank of water where as here you just have a pump going

[@Mobay18]

How efficient is this? How much Hydrogen vs watts used?

[@MexicanCanBreakToo]

You get less energy than you put in. Not sure about exact numbers

[@ornf_]

and here i was thinking you get more energy than you put in, defying all laws of physics

[@MexicanCanBreakToo]

+Ornf That's what I'm here for ;) Can't let you keep a false belief.

[@MexicanCanBreakToo]

+Ornf But for real, there is also a possibility of yielding the same amount of energy. Satisfying the definition of efficient which was the original question. So I wanted to address the question to that extent.

[@Mobay18]

I was just wondering since you can get 50 Liters of hydrogen for 30$. So it might be pointless to do this at home.

[@antonhelsgaun]

Was the loud knocking noise when you melted the nail flashbacks?

[@Kurtsi]

Is the cell itself heating in normal usage? I wonder what is the efficiency of the cell.. If the PSU supplies for example 500W, is 400W transferred for heating the water and 100W for producing HHO?

[@harleyme3163]

mines running just luke warm 12volts at 7 amps... its a + N N N N N - rig

[@ILikeWafflz]

What is the exact function of the safety bubbler?

[@versagertheCK]

He cleaned those screws really well

[@oscarzt1652]

what was that grey plastic film that said 40 MIL?

[@rodolfokiczka2138]

Hello Sir. Does this system that you made, DOES it SEPARATE the hydrogen and oxygen gases? In other words, the gases come out separately from the generator or do they separate on the plates but come out together through the same outlet? Thank you very much for your reply.

[@dariusblemovici7734]

they come out together from the generator, but do not react with each other until they are lit by the flame

[@greydior7253]

how many days the water will last in the container?How many cup is to be refill in every week?

[@chriscruise2305]

Hi can i asked for the dimensions of the stainless steel youve cut in mm? Thanks

[@givanildogodinho7553]

Can you separate the gases H and O for a safety use with this eletrolyser?

[@scagetman]

i use sparkle toilet cleaner to clean the plates. does it real fast, dip the plate in and wipe off

[@lukedare-white3131]

Is it just pure lye?

[@petergoestohollywood382]

and don’t lye to me!

[@lordsOneSheep]

Is oxygennproduxed OK to breathe or is it dry or something

[@JoaoPaulo-mr7ln]

Hi. What is the function of the membrane covering the electrode?

[@martincortezortiz9064]

Thanks for sharing. Great video.

[@harleyme3163]

havent had to clean mine since I bought it 3 years ago.. thing is... the plates arent just normal stainless.. they're 316L grade stainless... which is the most resistant to grain boundary carbide precipitation.. aka the leaching of iron into you water.. I also use 9x distilled water so it has no mineral's or elements in it either. still looks like when I bought it.

[@davelawson2564]

what is 9x distilled water ? And how many hours have you run it ? what do you use the hho gas for ?

[@Mephiston]

I don't suppose you would be willing to put up a detailed parts list somewhere?

[@nepal192]

sir can it used for cooking stov?

[@shoaibqaiser8720]

anita thapa u can cook using hydrogen not oxygen bcz pure oxygen create high heat same like video

[@chotugupta901]

anita thapa

[@woobyvr9654]

Question What's this used for

[@hansbengtonbengton9486]

To generate Hydrogen and Oxygen.

[@woobyvr9654]

Hans Bengton Bengton I know that :P but what is the hydrogen and oxygen used for

[@hansbengtonbengton9486]

QuebeC :D You can create an explosion with Hydrogen and Oxygen, you can use it for testing, you can use hydrogen to make your voice funny.

[@hansbengtonbengton9486]

QuebeC :D And you need oxygen to live

[@bulusuananthaprasad3134]

Sir, Can we do brazing also. WHere from we will get kits for purchase and its cost may please intemated

[@theradster3333]

Your neighbors must love you.

[@varegvalance5143]

What is the gas flow of your generator? How much litre per hour?

[@jberry7640]

What are the gaskets made from?

[@JoseGomez-ge2kw]

+Squirrely Nations how big and wide is the plate

[@JoseGomez-ge2kw]

+Squirrely Nations what size is the plate

[@JoseGomez-ge2kw]

+Squirrely Nations where do you buy the plate

[@mustardjar5707]

doesn't more volts make more hydrogen?? sorry if it might be a stupid question but i don't know anything of this and i'd like to build one of this generator

[@makeshifttechnology1738]

More volts AND more plates can make more hydrogen.The most efficient hydrogen production happens when you apply 2.5 - 3 volts per plate.If you just increase the voltage it will not increase the production as much.

[@lennox1558]

What is your electrolyte?

[@buder5116]

what is that gasket material ? Ps: I Want Hydro splitter To Get Pure Hydrogen :) already got a complicated plan for it

[@Б.И.Н.О.Р]

eto vce xuynya

[@greibanpintom.4980]

Hoy many amp do you use?

[@goofyvids2978]

Which Material is Neutral Plates Made of carsandwater?

[@davelawson2564]

same as other plates but are not connected to either + or -

[@smoothrider900]

questions adding sodium or pottasium does it affect the quallity of oxygen ? can u breath it ? does actually make someone feel "better" breathing just oxygen ? what about hydrogen ? what happens to the hydrogen coming out of the electrolysis ? where it goes ? in order to make the blowtorch u make a small tip at the end so oxygen comes out at higher speed ?