I made a DIY ROCKET STOVE!!

In todays video I fabricated a rocket stove from steel parts lying around my workshop. home you will enjoy the video :)
If you enjoyed, remember to subscribe and comment!
Link for home page: / @juliusthefabricator18

[@raysimon1368]

Nice job on your build I'm going to copy your rocket stove looks good thanks for sharing

[@JuliusTheFabricator18]

Thank you for the comment. It really means a lot :)

[@angelgegege]

Great work, my friend! :)

[@JuliusTheFabricator18]

Thank you :)

[@agentotten]

Nice video!

[@JuliusTheFabricator18]

Takker

[@christianmeldgaard7863]

Fed video joller 👍 Godt lavet 👨‍🏭

[@JuliusTheFabricator18]

Tak du

[@martinfabrin4354]

Godt lavet Julius Keep it up

[@JuliusTheFabricator18]

Takker

[@Dini-jf5bt]

Good stuff, I’m looking into building a rocket stove hot water heater

[@JuliusTheFabricator18]

Yeah man, great idea and thanks for the comment

[@jeangiachino4497]

Thanks for your video I like the way you make your Rocket stove! That’s the way I will be making it.

[@JuliusTheFabricator18]

Thanks for the much appreciated comment. I will be making more rocket stoves in the near future.

[@nobueno8652]

I’ve seen other KZbinrs build smaller rocket stoves and some are actually functional by at least brewing a small pot of water for tea. 😆

[@JuliusTheFabricator18]

I is possible to build rocket stoves in any size. It is just important to keep the ratio of the pipes correct. Thanks for the comment :)

[@AzraelEnterprise]

So when are you going to show us you cooking with it?

[@JuliusTheFabricator18]

I will be making a video about that soon :)

[@ericsand1390]

Very Nice Work

[@JuliusTheFabricator18]

Thank you for the much appreciated comment 😀

[@arthurroth5918]

Hello Julius, very nice video. Keep up the good work. You got your work well planned out, pre-cut all the parts, and did a nice job welding it all together.

[@JuliusTheFabricator18]

Thanks for the support, I really appreciate you for taking the time to write a comment

[@jonash9293]

nice video

[@JuliusTheFabricator18]

Thanks :)

[@wizrom3046]

Looks like there is not enough airflow. The sticks should not be burning all the way to their top. You need a 4 inch by 4 inch airflow IN the bottom to run a 4 inch by 4 inch vertical rocket pipe

[@JuliusTheFabricator18]

Yeah, i think the ashtray is constricing the airflow, but I will be making other iterations that work better and burn more efficiently

[@wizrom3046]

@@JuliusTheFabricator18 some of the best working designs I have seen have no flaps on the 2 lower pipes, just open. And a taller vertical pipe to get a bigger up-draft, so it sucks air in both the lower pipes. They rocket really well! Sucking plenty of air in through the wood tube means the wood is cooledmand only burns at the bottom, if the wood is burning up inside that wood tube there is a problem. Great video, thanks! 👍😎

[@JuliusTheFabricator18]

I will try that out and thanks for watching ​@@wizrom3046

[@andrewford80]

Nice! Is that 5mm thick steel tube?

[@JuliusTheFabricator18]

No, it is 4 mm tube. I have made a new video where I built a rocketstove in 3mm steel.

[@frederikpedersen5698]

🥥

[@JuliusTheFabricator18]

👍