I2C LCD not showing Text | I2C LCD Errors Fixing || 16x2 LCD not displaying Text || Lcd.begin();

Dear Viewers,
======================================
************Donation Link************
----------- rzp.io/l/TeachMeSomething -------------======================================
#TeachMeSomething #Arduino
============================================
Code & Circuit Diagram
Program Download Link 1 - bit.ly/3qbvhmB
Program Download Link 2 - drive.google.com/file/d/1ePbl...
Password: teachmesomething
============================================
========
Chapters
========
00:00 Introduction
00:10 4 Types of errors

[@user-bm7cn3qn7y]

I have struggled so long to get my screen working. This video fixed my problem in a matter of minutes. Thanks

[@TeachMeSomething]

Thank you brother. Subscribe and support

[@thinkingjohn2099]

Thank you so much your video fixed my LCD screen with the 12c board attached I had 3 errors , basically I had to add the liquid crystal 12 c library, change the begin to init instruction and run the 12c scanner file to change the LCD address so then it came to life, then had to make same changes to the sketch for the project I am making which is a Ultra violet light sensor used for measuring the suns strength to know when skin protection is needed

[@BHAGATKALI]

THANK YOU very much. truly THE BEST VIDEO ON I2C interfacing of LCD with ARDUINO. Thanks Once again. keep the good work going. good luck for future. May god bless you.

[@TeachMeSomething]

Thank you...

[@unihunt-5083]

Thank you for this video! I've struggled to find the reason why my LCD doesn't show text for over an hour and it was really that simple haha

[@TeachMeSomething]

Simple vs hard. If you know, It is Simple. If you don't know, it is hard.

[@62perc_26]

same thing happened to me LOL, new to arduino, decided to buy an LCD with I2c. blank screen expected as said from the seller but just needs tuning, searched around the internet to fix the backlight with i2c, turns out from this video you just had to rotate the screw on the i2c 😂🤦

[@TeachMeSomething]

Thank you

[@malithjayalath6417]

Thank you very much struggled for almost 2 days

[@musicforever2186]

Thanks! It was very useful video...

[@christianjunesausa1485]

I have been solving it for an hour but it won't fix. Thanks to you, I finally fix it, so thank you so much.

[@TeachMeSomething]

🙏🙏🙏

[@Sharkbar_]

Thank you, No. 3 fixed my problem.

[@HuntersHunt13]

Thank you so much, i can know what the problems. Now i can finish my job 👍

[@TeachMeSomething]

I have uploaded 50 LCD Animation Video using only arduino & lcd without other components. Also uploaded many projects using lcd. Watch and support to my channel. It will be motivation for me to more projects. kzbin.info/www/bejne/omrYpoigeNF-ZqM

[@gilanggemilang1149]

Thank you my brother 👍👍

[@adityabhambhani207]

THANK YOU SO MUCH......LITERALLY THE BEST VIDEO ON I2C ERRORS OUT THERE

[@TeachMeSomething]

Thank you brother

[@BlasterRay]

I had thought I had a faulty LCD but this video actually fixed my issue of having only 1 bar showing

[@BlasterRay]

This is the ONLY VIDEO THAT COVERED MY PROBLEM

[@TeachMeSomething]

Thank you

[@TeachMeSomething]

Thank you

[@BlasterRay]

Thank you for making a good video

[@vickyzulfiqar6749]

Thank you so much bro❤️❤️

[@Projectswithmani]

Thank you for this video

[@bimsarasenarath2665]

My problem solved (Error 3). Thank you.

[@surrenderToHim]

Thank you so much, i was facing some problems in display the contents and this video helped a lot

[@TeachMeSomething]

👍

[@onurtekingundogdu9568]

I love you so much.. 3th one solved my problem

[@TeachMeSomething]

Subscribe & support my channel brother

[@StephanWeibel]

The contrast adjustment helped. Thanks

[@TeachMeSomething]

🙏🙏🙏

[@ngkean9743]

Thank you...u my coding god...lemme humbly subscribe to you. Really thank you like really.

[@TeachMeSomething]

share the videos to your friends. watch this lcd animations & try yourself

[@TeachMeSomething]

kzbin.info/aero/PLYL7cTjwG3K8bousscCPdw9ad0aW42yPc

[@thegreatdragonshow]

Thank you so much, My Display has Error no. 3 And now it is solved 🤘😇👌👌👌

[@TeachMeSomething]

Thank you for your comment. Keep watch my channel videos. I have 75 lcd animation video in my youtube channel with program. You can try. 👇👇

[@TeachMeSomething]

kzbin.info/aero/PLYL7cTjwG3K8bousscCPdw9ad0aW42yPc

[@RaviRanjanKumar-cw8rs]

bhiya ki jai bhiya mai rat ko 3 bje tak isise [idit tha thank u so machhhhhhh..

[@TeachMeSomething]

🙏🙏

[@soumiaelboussidi2231]

Thank youuu so much, it works successfully for me

[@TeachMeSomething]

Subscribe & support my channel.

[@LimBo3500]

Thanks, helped me solve my issue (contrast pot)

[@TeachMeSomething]

Thank you

[@jundewana]

Thank you sir, you help me to fix the error

[@TeachMeSomething]

Thank you

[@kusalviduranga7352]

THANK YOU SO MUCH 😍

[@TeachMeSomething]

Keep support my youtube Videos Sir

[@cuong091087]

Thank you so much 👏👏

[@TeachMeSomething]

Thank you brother

[@sleverything4635]

Thanks sir

[@mukuldas6015]

Thanks it did help a lot

[@TeachMeSomething]

Subscribe & support my youtube chennel

[@Isaac_blingz]

thanks soooo much,,helpful

[@TeachMeSomething]

🙏🙏🙏

[@jexag]

tysm 😃

[@nipunwijewardhana3623]

Thank you sooooooooooo much...i wish you good life thanks

[@TeachMeSomething]

Thank you brother

[@legendkevin]

thank you so much

[@TeachMeSomething]

👍👍👍

[@AbhinavKumar-fy1nj]

thanks

[@vaishnavikulkarni7539]

Thankyou so much

[@TeachMeSomething]

👍🙏🙏

[@mkrdeveloper]

thanks a lot bro

[@TeachMeSomething]

👍👍👍👍

[@bahubali4963]

Thank you so much sir

[@TeachMeSomething]

Subscribe & give your support for my future videos sir

[@elalternatives9635]

thank you brother

[@TeachMeSomething]

👍👍👍

[@ayoubrez7039]

thank you soooo much 🥰🥰

[@TeachMeSomething]

🙏🙏

[@anghuyphamnguyen3096]

I have another problem and wonder as if you have any idea So my LCD for some reason only show the first letter of the lcd.print command, (for example if I write "Adruino", all it appear is A)

[@TeachMeSomething]

Give delay after your text.

[@uwaissani377]

Thanks a lot , I just need screwdriver

[@sametbrhan]

it works thnx bro

[@TeachMeSomething]

👍

[@benmedka]

Thank you

[@TeachMeSomething]

👍

[@danicageneston4764]

Where is the link for the i2c library?

[@llumanoj]

Sir I'm using 8051 microcontroller APFC Project this video thumbnail jese Display show Kar hae please reply sir problem 😥

[@Swapankumarmandal12]

Thanks

[@TeachMeSomething]

Welcome

[@yasserboutslighoi4003]

i love you man

[@TeachMeSomething]

👍

[@MSalim21]

hi when use i2c scanner it says no i2c devices found any fixes i have done all other steps?

[@TeachMeSomething]

Which board you have?

[@rafia5326]

Thank you , need to adjust the light , my was to bright , and init()

[@TeachMeSomething]

🙏🙏

[@simplybroken1735]

Thanks but solving all 4 types of error didn't work for me ,still no display in LCD

[@navrajsingh2300]

Sir can we use lcd without soldering just on pin header

[@TeachMeSomething]

No

[@harshithvishwanathan4419]

sir its not working for me ,pls help , i have found the 12c address as 0x27, and i adjusted the screen brightness also , but still the lcd only shows black boxes

[@TeachMeSomething]

Today uploaded another video try it

[@venketeshjain8551]

Best method for such problem will be to tighten or loosen the screw behind the i2c module in a small blue box(potentiometer of display) it will change the contrast of display due to high or low contrast these boxes appear. This solved my problem hope will solve yours also

[@TeachMeSomething]

🙏🙏

[@navrajsingh2300]

Sir can I use Arduino mega in place of Arduino uno for code ,,will it work same

[@TeachMeSomething]

Code is same. Circuit is different

[@muhammadadamamli6501]

Thanks 😭😭😭❤️❤️❤️

[@TeachMeSomething]

What happened brother?

[@muhammadadamamli6501]

@@TeachMeSomething My LCD not displaying any text 😭 The problem is lcd.begin(); I'm changed it to lcd.init(); Now my LCD can displaying text ♥️ Thanks for your help 🤧❤️

[@el-diablo7901]

I hv the backlight error but for an lcd without I2C

[@TeachMeSomething]

Lcd Pin number 15 & 16 connected?

[@icebean9291]

my lcd I2C shows only the first letter can you help me please

[@TeachMeSomething]

Did you use which program?

[@clicksandbeeps61]

I had the first error, but it didn’t fix the display to upload code. I checked, and everything is in the right place

[@TeachMeSomething]

Solved your problems or need help?

[@clicksandbeeps61]

Solved! Thanks

[@keeeerthan]

In my lcd it is showing only "H" in the screen where i gave print "Hello, world!"

[@keeeerthan]

Please help

[@TeachMeSomething]

May be program error. Or setting issue.

[@TeachMeSomething]

Contact me Instagram. I will solve your issue in zoom meeting

[@gayansiddhaarth4415]

bro in my display I see only the square boxes can't my text. everything is alright no error and back led glowing fine

[@TeachMeSomething]

Did you find i2c scanner value? Did you connect the pin with a4& a5? A4 & a5 for uno / nano board only.

[@TeachMeSomething]

Did you adjust the screw?

[@gayansiddhaarth4415]

bro saw your other video it shows that problem is because of enable pin loose contact but bro i have soldered it with a i2c help me bro

[@TeachMeSomething]

Watch the full video clearly. You need to find the i2c value first.

[@gayansiddhaarth4415]

@@TeachMeSomething uno board bro

[@IMRANHOSSAIN-gc7ui]

Where is the zip file??

[@TeachMeSomething]

It is description only. 2 files available check it

[@vardhanibadinedi8022]

I want i2c scanner code

[@TeachMeSomething]

It is available in example itself.

[@architrana302]

Sir mine error is not fixed

[@TeachMeSomething]

Did you find an i2c scanner value? Check soldering?

[@benmedka]

126 comment, inly 592 likes 😢

[@TeachMeSomething]

Yes. , 🙌🙌

[@NikhilWavare]

where is wire master zip file

[@TeachMeSomething]

See description