No.130 - Thurlby 30V-2A Bench Power Supply Repair

[@englishrupe01]

Excellent result. Thanks for showing all the troubleshooting stuff.

[@BrianBuchan-j9w]

Great informative video Ian. The mention of track pins brought me back to the Rigserv days...😂

[@IanScottJohnston]

Cheers Brian, great to hear from you!.....yes those were great days, oh to be a youngster with a soldering iron again!

[@Billguin]

Well done. I have one of those and a couple of fancier digital supplies, but the simplicity and quietness of that one means that I use it 95% of the time. Great little unit.

[@DaveCurran]

I like those old Thurlby power supplies. First used those at school in the 80s, still have a couple on my bench today.

[@jimmy2drinks]

@@PhatTony-km3fl Deffo. We had some in daily use at an FE college I worked at in Liverpool only a few years ago.

[@Petertronic]

My college had them too, late 80's

[@Petertronic]

Good repair job with interesting explanations of the circuitry too. My fairly new TTI equivalent of this unit still uses 2N3055's - they really love that transistor!

[@absurdengineering]

2N3055 was designed to be a very robust part. When properly heatsunk, the SOA is large. It’s sort of a no-nonsense trusted building block. Old reliable. Proper heat sinking is key though.

[@erikdenhouter]

I have power supply with the same spec's, 0-30V 2A, but it uses only one 2N3055. That transistor can handle 115W 10A, if properly cooled. Here we see FOUR of them.

[@absurdengineering]

@@erikdenhouterMakes it robust. A 2N3055 will dump a 100W, but not at full rated C-E voltage IIRC.

[@erikdenhouter]

@@absurdengineering I think they included some headroom indeed, it is the high transformer voltage that makes a large C-E voltage to begin with. Now I think of it, the power supply I was talking about uses a relais that kicks in when the unit is regulated over 15 volt. The reason for that is to go from one to two secondair windings, so below 15 Volt only one winding is used, hence half the needed C-E voltage is there :)

[@davidv1289]

Thank you Ian for another great repair video. I love the enthusiastic sound in your voice when these old units spring to life! Cracked solder joints around "bulky" items like connector pins, IC sockets and your trace pins seems to be a common problem - I assume it is related to thermal expansion and contraction.

[@IanScottJohnston]

No doubt the amount thermal expansions and contractions this unit has had it its life much be pretty high!

[@HeyBirt]

Thurlby and Thandar...sound like characters in a children's cartoon sci-fi show. :)

[@964tractorboy]

A couple of good repairs on PSUs with the venerable 2N3055, or "dirty thirties" as were known. Classic!

[@fichambawelby2632]

Thank you for your excellent videos, Ian. They are always welcome.

[@graemedavidson499]

I have a few Farnell power supplies that appear to share the same aesthetic. I got them in the late 80s and think they could outlast me!

[@larrybud]

Socketed chips sometimes just need to be pulled and reinserted to break any corrosion.

[@louco2]

Learned something new today so thank you for taking the time to do this video. Liked and subscribed!

[@followthetrawler]

Wow - I had forgotten PCB pins - when I was draughting PCB layouts with tape back in the late 70's I always considered it a personal failure if I had to use them :) Nice fix and restoration Ian.

[@IanScottJohnston]

So had I until I saw the tell tale blobs of solder on the topside of the Pcb. Thinking back, I must have inserted 1000's of track pins onto bare Pcb's back in the day. I always remember some disasters when the soldering iron slipped!

[@absurdengineering]

@@IanScottJohnstonWhen I was a wee lad, I went fancy with resistor leg off-cuts. But I did the off-cuts before even installing the resistor. Resistors make for nice little wire holders. So first I’d solder a resistor forest - a “tree” in half the vias. Then I’d cut them off, and repeat with the other not-yet-cut leg in the rest of the vias. Cut those off to free the resistors again. Then the resistors were soldered onto the board. Worked fine for hobby projects. I dread fixing the PCBs that had little rivets for the vias. Those would always get unreliable and were such a pain to get solder to stick to. Atmosphere - good for us, bad for the connections 😅

[@IanScottJohnston]

@@absurdengineering Never much had a problem with track pins unless they had been sitting around for a good few months, then they had oxidized a little and were hard to solder on the underside. But, the biggest pain with them was teaching the junior techs how to install them......need quite a bit of force with the soldering iron to get them down into the hole properly......and mucho scope for skating the soldering tip across the board!

[@absurdengineering]

@@IanScottJohnstonMaybe yours were better made. The usual old US-stuff was all riveted on with a press, straight onto tinned traces. The rivets were tin plated too. No soldering whatsoever. Maybe that was the problem.

[@brendanbarbour8568]

Great job again Ian. Another veteran PSU back in service… 4 2N3055 series pass devices seems excessive at first , but it’s probably wise…!

[@darrenmurphy6251]

@@brendanbarbour8568 from my own days making my own supplies having enough heatsink to prevent thermal runaway, and getting enough thermal transfer is the reason for 4 pass transistors and 2 heatsinks, I learned that the hard way charging nicad packs to boiling point cause the psu overheated and drove flat out into the pack, for some mad reason I thought thermal runaway only effected audio amps, I was only a kid fixing tvs no training

[@TheBreadboardca]

love those 2n3055 transistors, oldie but Goode power device, I still have a few new old stock myself, never know when you will need them right ? :), simple repair this time, nice one.

[@grahamhall2662]

Fascinating, well done. Just bought a Farnell LT30/2 in great condition. Seems to be a nicer implementation of the genre with the analogue dials. Amazing how similar it is to the Thurlby.

[@graemedavidson499]

I’ve had one for 35+ years and it’s still my main go-to PSU. Only thing that ever failed on it was the mains switch power LED!

[@DavidSmith-zx7wz]

Love the equipment repair videos!! Thanks

[@ahc1625]

Thandars of a certain age can suffer with intermittent problems on the wipers of the open frame trimmer pots. You can clean them up and they will last a while longer but eventually play up again. Best to replace them all is what I have found over the years. May of been the cause of your erratic output until disturbed. Apart from this though, most older Thandars are excellent supplies and will literally last you a lifetime !

[@gwc1410]

Hi Ian. I really enjoy your repair videos. They are educational and entertaining. I just sit back in my chair, watch, and see whats wrong with the device. I've been subbed for quite a long time. Who draws the little cartoon character in the corner of your videos? It's very well done.

[@IanScottJohnston]

The original cartoon character was a graphic I found on the web many years ago......he was holding a flag or something, I contacted the author and paid a couple pounds for the royalty, then I modified it so he holds test gear/tools instead (with the authors blessing). Eventually, I went to fiverr and got a guy to create small video clips of him doing various things. I have a wee collection now for various purposes which I have integrated into Davinci Resolve.

[@TheEmbeddedHobbyist]

I'd have that power supply over any switch mode power supply for low power work. Except for any emc testing, for that you want the analogue meter type. Those digital displays really conduct noise down the outputs lines. Also fhe fact that they go up to 32V was great as the normal upper voltage tests on a aircraft 28V avionics was 32V. So you could just wind the output up to max and your there, maybe a little bit high but never too far over. Nice fix. Could always find that a nice home on the bench 😂😢😅

[@darrenmurphy6251]

i love the tti variant twin tracking pl330qmd ,they now pcb mounted all parts and everything is on plugs /sockets except the mains switch (which i fitted an inline plug/socket ) for great access ,you can unplug the whole front panel ! only thing is i have a preference for having single 10turn voltage/ current control rather than coarse/fine but theres no pcb to front panel clearence to do that. rather strange that they stacked loads of heatsinks instead of relay selecting multiple secondary windings to reduce dissipation , and the twin tracking is crazy confusing with floating grounds and negative biases , iam dreading a fault with dual tracking! so i now have 2 so i can compare fault find ,if needed i prefer analog test gear whenever possible , no discontinued microprocessor with unavailable firmware suffering code amnesia!

[@jimmy2drinks]

Nice work Ian :)

[@stevenbliss989]

You might want to use a "ring counter" to really check the transformer.

[@tonybell1597]

Excellent .... great result ..

[@philiprogers5772]

I watched in anticipation of you showing me how to calibrate the voltage and oh no you did it off camera. Any chance of some bonus footage?

[@joelkist6493]

Nice work ! I can't help myself from commenting on the length of that screw driver bit; you don't want to get to close to your work🤣.

[@IanScottJohnston]

I've since bought a longer 300mm screwdriver so next time I don't have to remove the heatsinks...:-)

[@eded8045]

when you re-soldered the IC pins did you wick away old older and replace with leaded and use flux? Its what I would do

[@IanScottJohnston]

I don’t always wick off old solder, it’s a case of resoldering the first and seeing how it accepts new solder and more importantly new flux. Balance this up with desoldering the entire IC which can subject the IC to a bit more stress.

[@charade993]

Nice!

[@ahmedalshalchi]

My best Engineering school lab instrument and also my early workshop benchtop instrument ... One thing bad about it is they used bad wiring technique ... Ian , can you please share me the schematic diagram of this model please ?

[@TheEmbeddedHobbyist]

A star grounding point, that's something that the KZbin designers should pick up on. Very rare to see any design pcb's where ground noise reduction has been considered let alone implemented 😢😂

[@IanScottJohnston]

Reason: It's too easy in KiCad to drop a ground pour I think. I know I'm old.......but I really like working on this older gear and working with the technologies and implementations we used to do daily in the 80's.......sniff!

[@TheEmbeddedHobbyist]

@@IanScottJohnston these were the power supplies i grew up with. Kingshill power supplies for the higher voltage or currents. and Levell TM3B's for the audio measurements. Still have an HP distortion analyser under the bench, still works!

[@MitzaMaxwell]

Four 2N3055 for 30v 2 Amp isn't that overkill? A TO3 2N3055 is a 15 A 115W transistor., I have a 40 year old 30V 3 Amp with only one 3055 transistor. However, it has a relay that changes the voltage on the transformer. 30v x 2 A = 60W why did they use four 2N3055?

[@MitzaMaxwell]

OK their input AC voltage is reasonably high when it gives 55V DC. So it gives 110W with max load at lowest output voltage, so I can agree to use two 2N3055.

[@tonyh6309]

Like almost all figures in the glossy sales brochures, the 15A, 115W figures are theoretically possible, but only in *very* specific but usually unrealistic conditions. In this case there are three different operating regions to consider, which are shown in the 'safe operating area' chart, or SOA. (Bottom of page 2 for the ON-semi 2N3055-D): Region 1) Voltage < 7.5V. Here the 2N3055 is specified at 15A max; that is determined by the current carrying capability of the wire bonds connecting the silicon to the case connections. But note that all the other specification graphs for the 3055 only go up to 10A meaning useing above 10A is at your own risk and performance is unspecified - it just shouldn't destroy itself below 15A. Region 2) Voltage between 7.5V and 40V. Here the maximum current is determined by the 115W power disspation limit of the transistor. Eg. at 25V, the maximum collector current is 115/25 = 4.6A. Not too shabby eh? *Except* this is only true when the case is kept at 25C (or less). This arises from the maximum junction temperature limit of 200C and the junction to case thermal resistance specified at 1.52 C/W. Keeping the case at 25C when the transistor is dissipating 115W is virtually impossible without liquid Nitrogen or the like. A very good heatsink (without forced air) would be 0.5 C/W, but the TO3 case to heatsink insulator (mica or whatever) might add another 1 C/W. Bench PSUs are typically specified to operate in an ambient temperature of up to 40C. So (200C - 40C)/(1.52 + 1 + .5) = 53W maximum dissipation. So now we need at least two devices for a 32V/2A supply. Region 3) Voltage > 40V. This region is subject to secondary breakdown of the transistor where the reverse biased collector-base junction's breakdown voltage decreases with increasing collector current so the maximum allowable current is much less than that calculated in region (2). In the video, Ian measured the voltage on the main capacitors as 55V. When the supply is shorted, current is limited to 2A max but the total dissipation of the 2N3055s is now approx 110W. In reality the 55V is the unloaded transformer voltage so at 2A this will drop by perhaps 10%. *But* the PSU designer has to allow for the mains voltage to vary by +/- 10% from nominal so the 55V might be the worst case (but we don't know what the mains voltage was in Ian's lab at the time). The SOA graph shows the max current is approx 1A at 55V, (ie. 55W) - again with the case temperature at 25C. Taking all factors into account it is hard to (safely) get a 2N3055 to dissipate more than 20 to 25W, especially when operating at high voltages. Don't forget to add a large margin for long term reliable operation and you can see why they use so many devices in these linear supplies.

[@gadgetwob]

Tony did the math. Those infinite heatsinks are rare beasts indeed 😂

[@MitzaMaxwell]

@@tonyh6309 Many thanks for the thorough and instructive answer. You are correct, with the high COLLECTOR−EMITTER VOLTAGE (VOLTS) I can see that it is necessary to have at least four 2N3055 at 2 Amp. Due to (THERMALLY LIMITED @ TC = 25°C) according to ON Semiconductor data sheet. Thanks for the reminder.

[@worroSfOretsevraH]

Don't worry, I surely prefer to look at a real oscilloscope instead of a web app.

[@GapRecordingsNamibia]

Hi Ian, just a qiestion if I may.... Why are there 4x 3055's for only 2A? Is it because of the low gain of the 3055's or because of the dirve circuit? Thanks.

[@IanScottJohnston]

The more transistors in parallel the better as it makes it easier to control and keep lower temps, especially making sure the temps are equal across them all. Any difference in temp between each of them can mean unequal collector currents and thus more likely thermal runaway can occur. Also, each transistor has an emitter resistor to help balance each transistor load, so ohms law comes into it now and the heat generated on each resistor.

[@GapRecordingsNamibia]

Thank you for the explanation, I just thought that 4 would be overkill for the amount of current being drawn, and, would have thought that 2 would've sufficed. But, I suppose, that the over engeneering is why they are still around. Thank you again Ian... Have a good day...

[@tonyh6309]

[Part 1] Like almost all figures in the glossy sales brochures, the 15A, 115W figures are theoretically possible, but only in *very* specific but usually unrealistic conditions. In this case there are three different operating regions to consider, which are shown in the 'safe operating area' chart, or SOA. (Bottom of page 2 for the ON-semi 2N3055-D): Region 1) Voltage < 7.5V. Here the 2N3055 is specified at 15A max; that is determined by the current carrying capability of the wire bonds connecting the silicon to the case connections. But note that all the other specification graphs for the 3055 only go up to 10A meaning useing above 10A is at your own risk and performance is unspecified - it just shouldn't destroy itself below 15A. Region 2) Voltage between 7.5V and 40V. Here the maximum current is determined by the 115W power disspation limit of the transistor. Eg. at 25V, the maximum collector current is 115/25 = 4.6A. Not too shabby eh? *Except* this is only true when the case is kept at 25C (or less). This arises from the maximum junction temperature limit of 200C and the junction to case thermal resistance specified at 1.52 C/W. Keeping the case at 25C when the transistor is dissipating 115W is virtually impossible without liquid Nitrogen or the like. A very good heatsink (without forced air) would be 0.5 C/W, but the TO3 case to heatsink insulator (mica or whatever) might add another 1 C/W. Bench PSUs are typically specified to operate in an ambient temperature of up to 40C. So (200C - 40C)/(1.52 + 1 + .5) = 53W maximum dissipation. So now we need at least two devices for a 32V/2A supply.

[@tonyh6309]

[Part 2] Region 3) Voltage > 40V. This region is subject to secondary breakdown of the transistor where the reverse biased collector-base junction's breakdown voltage decreases with increasing collector current so the maximum allowable current is much less than that calculated in region (2). In the video, Ian measured the voltage on the main capacitors as 55V. When the supply is shorted, current is limited to 2A max but the total dissipation of the 2N3055s is now approx 110W. In reality the 55V is the unloaded transformer voltage so at 2A this will drop by perhaps 10%. *But* the PSU designer has to allow for the mains voltage to vary by +/- 10% from nominal so the 55V might be the worst case (but we don't know what the mains voltage was in Ian's lab at the time). The SOA graph shows the max current is approx 1A at 55V, (ie. 55W) - again with the case temperature at 25C. Taking all factors into account it is hard to (safely) get a 2N3055 to dissipate more than 20 to 25W, especially when operating at high voltages. Don't forget to add a large margin for long term reliable operation and you can see why they use so many devices in these linear supplies.

[@GapRecordingsNamibia]

@@tonyh6309 Yes, that is more or less the assumption I came to when I saw the 55V across the caps, that-that would be the contributing factor as to why there were 4 of them as the 2A seemed like child's play..... You have clarified that for me..... Thank you kindly for the VERY detailed writeup. It is not often that one still gets responses like yours to individuals like myself who genuinely ask a valid question in order to be able to gain some good, sound insight into why things are done in the manner they are, hence why I said that this is why this power supply is still around and working...