Hi, I have worked for an oxygen supplier in a combustion role for 32 years. I would recommend the following, Wash hands before starting Degrease tools and wear nitrile gloves The seals a made from viton and and must not use any O rings you have handy. The white lubricant is not grease but Krytox an oxygen compatible lubricant, also very expensive. I have seen firsthand what high pressure oxygen can do. Usually in accident investigation I can not find the valve or part burnt because it is vaporised ! That’s why the valve body and gauges are non ferrous ( brass) construction. Hope that helps, Ps love you work.
@Trudeautthebestt2 жыл бұрын
could you explain why the body and gauges are non ferrous metal like brass?
@MrDillaKilla2 жыл бұрын
@@Trudeautthebestt non reactive to not cause a reaction from oxygen at high pressure slamming into it. Look up Boyle's law.
@portalkeeper9782 жыл бұрын
Do you by chance also know the type of thread sealant used on npt or straight thread connections for gauges or other things attached to oxygen regulators?
@willthecat3861 Жыл бұрын
@@Trudeautthebestt Ever seen how steel rusts? That's the iron in the steel reacting with the relatively low concentration of oxygen in the air, and atmospheric pressure... slow motion burning. Now imagine if the steel starts to rust, and heat builds up enough so that the steel starts to burn,... and starts burning under 2000 psi of pure oxygen. The reaction is self sustaining, rapidly progressing, and catastrophic.
@obfuscated3090 Жыл бұрын
@@Trudeautthebestt Because iron oxide burns. It's half of Thermite! It also oxidizes easily.
@MrRebar153 жыл бұрын
*I C Weld* Used those gages all my life, never got into the guts. Thank-you sir for taking the time to show us. God Bless.
@samboslc2 жыл бұрын
Brings back my oilfield days; always enjoyed working on regulators and back-pressure valves. Great work Isaac.
@dnixon87673 жыл бұрын
Good video. The white grease looks like Krytox, an oxygen safe grease we use on gaseous oxygen handling systems.
@joandar13 жыл бұрын
Dalen Nixon, I will look that up, thanks for the info. For myself I was wondering if it may be a Silicon base, not that I know of that being safe with high pressure Oxy. John, Australia.
@jenniferwhitewolf37843 жыл бұрын
Christolube 111 is another high pressure O2 safe grease. Silicones are NOT used in high or low pressure O2 systems.
@joandar13 жыл бұрын
@@jenniferwhitewolf3784 Thanks for the info. John.
@willthecat3861 Жыл бұрын
@@jenniferwhitewolf3784 Yes they use this in dive shop, for the scuba gear. Or Nitrox. I'm not sure it has the same properties regarding high pressure oxygen, as Krylox does. You have to be careful to check what applications the specific grease/lubricant is speced for.
@obfuscated3090 Жыл бұрын
It is! Krytox also make a thread sealant but it's not cheap.
@Camera1931-p5v3 жыл бұрын
Learned something new today thanks! I used to send my regulators back to get rebuilt! I do not use my torches much anymore! Great video!
@willallison11363 жыл бұрын
My regulator just went out and I was looking for some videos on how to rebuild them. You're one of my favorite channels! What great timing! Thank you!
@supertramp60113 жыл бұрын
Be very careful to use only the right components which are oxygen safe,such as nitrile o rings or thread tape ,grease (Krytox) etc. Do not use standard grease or o rings.
@petermccuskey18323 жыл бұрын
Great tutorial! Thank you , I have two units sitting on the shelf that I will take apart armed with the knowledge.
@robertmanley75563 жыл бұрын
Good to know !! I have an argon regulator that was leaking gas was wanting to tear into it but not sure if I should . Just took it out of service and I am using different one .Even though this is an oxygen regulator I believe this gave me the confidence to at least look at it thank you for that !! A lot more simplistic inside than I thought !! Great video as always you're a true teacher !! 👍👍
@alanbranch8513 жыл бұрын
Never took my gauges apart, good to know info. Thank You 🤙
@mongomay13 жыл бұрын
Thanks for the entertainment, very engauging in regards to the subject matter! I was intimidated by all the "safety" aspects of servicing a diaphragm valve for gasses, even though I have rebuilt hundreds of plant air regulators, some we had on annual PM's because of process risks.
@mikegoodman41333 жыл бұрын
At the welding shop in our local school some years ago, the supplier was changing out oxygen bottles when an oil contaminated reg blew up on him. It blew a hole right through the case and sprayed him with molten brass. Luckily he had turned away just in time and so it got him in the back and burned holes in his parka, which was heavy enough so he didn't get burned. Shook him up pretty good though. Also remember to use Oxygen compatible thread tape. Regular stuff won't do.
@isaacchavezjr55563 жыл бұрын
That sounds like a number 10 on the sphincter scale.
@obfuscated3090 Жыл бұрын
Krytox make a TS4 sealant that's better than tape because it doesn't overly lubricate the threads. I've used both and prefer the Krytox. Prices vary greatly...
@billarcher3 жыл бұрын
I used to repair my oxygen and acetylene regulators here in Australia. It got to the point that parts are not available here so you are forced to buy new regulators.
@CumminsTurbo411 ай бұрын
It's starting to happen over here. Rebuild kit is $29. A new Chinese regulator WITH gauges on slammazon is $29. 😮😂
@Dmax04 Жыл бұрын
Mine is pretty similar to this one except my diaphram is rubber and it also does the sealing instead of an o-ring. I ordered a rebuild kit for $30.00. Never took a regulator apart before and didn't know what was inside. Like you said they are pretty simple. Thanks for the video.
@LoBeau533 жыл бұрын
I feel your pain Isaac. When you get older and the eyes start to go, you can weld by braille for a while but it is a hard way to make a living. You tend to lose sensitivity in your finger tips rathe quickly. Another one of the joys of being a business owner is that you get to spend your leisure time fixing and maintaining your tools so that you can be productive on the job
@timking86752 ай бұрын
Love the Stevie Ray Vaughan
@merlepatterson3 жыл бұрын
Excellent welder with impeccable music taste as well. I heard SRV in the background.
@supertramp60113 жыл бұрын
Thought I recognised the guitar!🤣🤣
@metalmetz3 жыл бұрын
Thanks for the video! Good to know these gauges are pretty simple to rebuild when the time comes.
@kenanderson93313 жыл бұрын
Thanks for the video maintenance is also a crucial point of getting the job done safely.
@warrenjones7443 жыл бұрын
Gas regulators are not complicated really. They just want you to think they are. What kills my regulators is the environment in which they live. Outdoors on a service truck from 90F degrees to -30F temperature ranges and dirt. They fill up with water and freeze in the winter if you don't keep em covered I found out😁. That style of Victor regulator is pretty durable and they work very well. Cheers
@OzarksWildman3 жыл бұрын
Good video! 👍 Regulator diaphragms are the disc shaped parts.
@timothyball31443 жыл бұрын
Thank you. Hopefully I remember this if I have troubles with my regulators.
@mikemiller90614 ай бұрын
Thank you sir. They want 250$ to fix that. Awesome job
@gregorycross6123 жыл бұрын
You were the only other KZbin channel mentioned by name in C.E.Engineering's live stream last week over in Australia. He does a lot of heavy equipment machine shop repairs for those not familiar.
@rwarren47573 жыл бұрын
That's how I found I C Weld by curtis mentioned him
@derrickguthrie47043 жыл бұрын
I actually need to do this to my leaking setup, perfect timing!
@RickAShriver3 жыл бұрын
Thank you for your time!
@terrminatoragain4613 жыл бұрын
Very simple,thanks for the tutorial Isaac,can you do a video with details about your torches,some of those torch bodies are amazing
@betty24ish3 жыл бұрын
Yes we would like to know more about that amazing truck of yours. You have a great set up. I know in the year you made lots of special but simple jigs
@campnut60763 жыл бұрын
I had an O2 regulator go bad 2 years ago. It put bottle pressure directly to my torch hose while I was holding it. I thought it blew my fingers off, hurt like hell. It was a Victor copycat , no parts available. I now have Victor regulators on my torches. They are worth the extra $$$.
@MrDillaKilla2 жыл бұрын
Flashback arrestors, and use quick connects with reverse flow check valves. Could never happen in that case
@granterwin2531Ай бұрын
You say to put tape on the threads to the gauges. You should not use regular white teflon tape on oxygen threads, though. You need green oxygen-safe tape. There are many brands but I use Gasoila. Keep up the good work. I worked ship repair for many years and the problems you fix in your videos are often very similar.
@davidsellars6463 жыл бұрын
Thank you. Have an oxygen regulator that needs fixing. This helps....
@METALMUNCHERS773 жыл бұрын
Good video man I just had some that went bad and just tossed them and grab a new set wish I would have seen this 2 weeks ago
@GaryForgingOn3 жыл бұрын
thanks. I wondered about fixing up some old gauges. I have a new victor journeyman set but I was at an auction for a welding shop closing up and I bought a 5 gallon bucket full of old gauges and torches. I'm not sure why but maybe I will see if I can fix some up for the fun of it. ;) Thanks
@michaelvangundy2263 жыл бұрын
I'm sure that you know about high pressure oxygen. Any spec of a combustible and they will be picking up your face in a bag. There is a huge risk using old poorly stored gear on oxygen. They blow up when you first turn on the bottle. And you're standing there looking at it. Nobody ever has a story about it because it leaves no witnesses behind.
@GaryForgingOn3 жыл бұрын
@@michaelvangundy226 thanks. Sounds like a good reason to not mess with them. I usually send off my equipment for repair. But didn't know what to with these old units.
@MrDillaKilla2 жыл бұрын
@@GaryForgingOn why not fix them?
@obfuscated3090 Жыл бұрын
Weldingweb forums have tons of info. It's also easy to sell them as cores but I bought a LARGE box like you did and have torches and regs and flowmeters for life. Easy to learn or just Ebay them (I took the ones I was selling apart since customers are rebuilders like me). If a torch head leaks it may need reaming (special reamer, the rebuilder can just ream yours if ya wish) but resealing them is easy as is replacing minor parts.
@GaryForgingOn Жыл бұрын
@@obfuscated3090 thank you. I will go through the box and check them out.
@davidmunro14693 жыл бұрын
Thank you man.I put leather gaskets in everything.
@tomscott47233 жыл бұрын
Always wondered what was hidden in there, Thanks!
@schlosserprofi86473 жыл бұрын
Thank you for your viedeos. Learnd a ton from them and motivated me to go out and do stuff. By the way, the grease on the regulator skrew is outside. No oxigan out of the bottle is reaching there, that's why they put grease there. Greedings from east Germany
@dyardsale54753 ай бұрын
Good to see, my vintage Craftsman leaks out the body, probably that o ring i'm guessing.
@agentbertram47693 жыл бұрын
Thanks Issac - most interesting.
@northmanlogging27693 жыл бұрын
My first set of torch gauges went bad after ? 20 years, local weld shop quoted my $125 to repair, a new regulater was $170... parts are $15 on the interweb. This of course happened while I was fixing a broke down machine, and needed the torches now, not in a week... So I have a mismatched set of gauges now.
@ShainAndrews3 жыл бұрын
Disappointed. I was confident you were going to dissemble the gauge with a surgical torch... then a wrench comes out. As always appreciate the knowledge!
@chrisbolton49003 жыл бұрын
I thought he would use the arc gouger, then tig braze it back together....
@ke6gwf3 жыл бұрын
It kind of scares me how many comments there are now thinking that they are ready to repair their o2 regulators based on this video, when they don't even realize the risk that skin oils, grease residue on the handle of your wrench, etc can create. It's not just spraying it with WD 40 that creates risks, it's any organic or oil, and it's not about the quantity, because the oil is just the ignition source, it's the metal that burns under the high pressure o2 atmosphere. The oil is thought of as the kindling, just creating enough energy to ignite the metal. This is really not safe unless you basically create a clean room environment, covering your surfaces with clean towels, washing your hands with dish soap, using degreaser on your tools and vice handle, and ideally clean nitrile gloves, and treating it as a sterile field so no oil can get close. Remember, one speck of oil can be the spark that turns the metal into fuel, and heat is created every time you open the tank valve and it increases the pressure in the HP side.
@taylorwso3 жыл бұрын
Yeah, you hear about it all the time, especially after thousands of these have been fixed in the field. They even have the audacity to sell replacement parts to anyone. Oh the noes. We should have the govt stop this practice.
@stevenakn13 жыл бұрын
I'm surprised they don't weld them shut if its so dangerous 🤔
@obfuscated3090 Жыл бұрын
You can work to oxygen safe standards without a "chip foundry level" clean room and commercial rebuilders just use a properly clean workshop area. The tool precautions you list are wise. Gloves are cheap so there's NO excuse not to have them and acetone is the classic way to clean oxygen system parts safely (I use it outdoors for obvious reasons). Not working around grease or filth is pretty basic but the world abounds in idiots... The factory manuals can be downloaded or tech support can email the link if you don't find them. Not nearly enough people use tech support but it's free so I do.
@ke6gwf Жыл бұрын
@@obfuscated3090 I never said anything about a chip foundry level clean room, I am talking more like an OR level clean room, or a hydraulic rebuilding clean room, minus the oil lol Basically where you have the mindset that you just described, thinking through the process of doing it in a way that ALL oil is kept away and removed, and most people don't even have comprehension of how to do that, or the possible sources of oil. It sounds like you could do it safely, but I am trying to warn off people who want to do it on their greasy work bench after spraying it with Brakekleen and wiping it with a freshly washed and fabric softened shop rag... Lol
@f0rumrr3 жыл бұрын
Your a great teacher man learn so much watching your videos.
@doctwiggenberry53243 жыл бұрын
Thanks for the work. Keep the vids going.
@williebulletman52173 жыл бұрын
Really cool video Iv never seen in side one of those gauges most people would just go out and purchase a newRegulator Americas good at throwing stuff away not manufacturing stuff anymore and that sad keep the great videos come in my friend I’ll dig it
@obfuscated3090 Жыл бұрын
In the welding world it's normal to have quality regulators rebuild via the local welding supply. A total noob might discard them though.
@ryanschnee93343 жыл бұрын
I fixed a cheap fuel gas regulator by cutting a new rubber washer out of a piece of tire tube. Still working. I have always been scared to work on the O2 regulator.
@obfuscated3090 Жыл бұрын
DO NOT use mystery parts on oxygen regulators. Fuel gases are less picky but I'd make sure at least to us Viton rings, seals etc. Inner tube doesn't do well in contact with petroleum products so I would resist the urge to use it.
@redpost23802 ай бұрын
Use compressed air to clean properly. Also that white teflon washer/spacer is a split washer so it is meant to have a cut
@donaldroberts64522 жыл бұрын
I'm sorry I didn't comment before, but I just bought a set of used guages today and your video is great ad always. Did you replace diaphragm.
@ICWeld2 жыл бұрын
no just the center piece.
@KarasCyborg3 жыл бұрын
I just got a new Aceyteline bottle from NAPA. It wouldn't seal with a brand new regulator. There was a bunch of crap, like teflon tape on the tank side threads. I know it's frowned upon to seal up tank threads with anything, but when you are force to do a cylinder exchange program and only find out after they are closed for the whole weekend, and you have something to do on a weekend warrior project, what would you do?
@MrDillaKilla2 жыл бұрын
Hand brush it out with a bristle brush, remove any debris, crack the bottle open to blow out the CGA fitting, examine the cone end for dents/damage and then attach regulator.
@obfuscated3090 Жыл бұрын
@@MrDillaKilla ^Perfect response all the way!
@michaelclark94093 жыл бұрын
Yep, they get you on those "wearables". But at least it's still repairable unlike most new stuff. 👌🏻👍🏻
@rockway633 жыл бұрын
Petroleum make go boom? 😁 I hope you get a million views on this one.
@budlvr3 жыл бұрын
Always nice to learn something new; you never know when it might come in handy!
@jimsvideos72013 жыл бұрын
Also the o-rings in them are made of special material, don't go just grabbing anything out of the assortment.
@isaacchavezjr55563 жыл бұрын
Definitely good idea to warn knuckleheads like me that would want to do something like that.
@obfuscated3090 Жыл бұрын
Indeed. Use Viton or other suitably rated material.
@ryansmith59783 жыл бұрын
Hey Isaac when you took the first bumper off yours was crack so is it supposed to be split or not? I just know you said you didn't know and I can't really tell on the replacement parts. And thanks for this video I have a regulator I need to repair
@ICWeld3 жыл бұрын
I think it was supposed to be a split washer.
@dans_Learning_Curve3 жыл бұрын
I have a leaking 02 regular. Might carefully dig into it.
@obfuscated3090 Жыл бұрын
STUDY first. Seal-Seat has a good catalog with exploded views. ASSUME NOTHING and you'll be fine. They're simple machines. Almost always the seat is leaking .
@ypaulbrown3 жыл бұрын
Isaac, have gone through a few O2 regulators in the last couple of years form Victor.....wonder what is up with that....I do not use that much either....great video Issac, best regards, oh yeah, my argon regulators are pooping out faster that they should.....I always relieve spring tension on diaphragm spring too after using....best wishes from Orlando , Paul
@pervasivemalaise3 жыл бұрын
many people are killed and injured by these valves. dust particles or any grease or oil including oil from your skin can cause the valve to explode. it is particularly dangerous when the tank valve is opened and it is recommended that the tank valve never be opened with the screw turned in to feed the torch. that means the low pressure side should not be open. as to overhaul the valve. it is fine if you know what you are doing and to degrease the valve and as another commenter posted wear oil free gloves. the problem is how do you know if you know. you can degrease the parts using detergent soap and water and dry thoroughly (leave overnight or put in an oven). do not blow dry with compressed air as that may be contaminated.
@gargar81963 жыл бұрын
I don’t remember what it was but I used to pay 30 dollars for a small o. ring and got smart and found it elsewhere for 10 cents
@mannyrodriguez89263 жыл бұрын
Where at!?
@gargar81963 жыл бұрын
@@mannyrodriguez8926 California It was also metric
@jifi-01783 жыл бұрын
Learned something new about viton (fluorine rubber) and krytox ( fluorinated grease with polytetrafluorethylene (PTFE) thickener), you know, just stuff the average joe/issac has kicking around the kitchen counter. 😛
@Illkilla19843 жыл бұрын
Sad thing is I could have used this video 2 days ago before I sent both my regulators off to be repaired by my local welding supply chain. Never again now so thank you
@briantruck2284 Жыл бұрын
Dropped my off Hopefully they rebuild it good
@obfuscated3090 Жыл бұрын
Most LWS don't charge much over the rebuild kit and if oxy regs are crusty I don't mind letting someone else polish them since that plus oxygen safe cleaning is more work. Either way saves money!.
@ypaulbrown3 жыл бұрын
Issac. so the white teflon ring is supposed to have the split? That is what it looked like when you reinstalled...thanks, Paul
@ICWeld3 жыл бұрын
I believe so
@deadwood37643 жыл бұрын
Question:had an acetalyne reg leaking it caught fire at reg and tank.Helper ran away i just turned gas off and it went out.I see the same spike in pressure like yours also leaks gas out of little air holes around reg.Is this normal.Cheap set of torches anyways.Can reg be fixed or better to get new sey of torches higher qaulity.Thanx appreciate your vids
@briantruck2284 Жыл бұрын
Buy rebuild kit
@deadwood3764 Жыл бұрын
@@briantruck2284 thanks Brian got better set found other issues.
@kennytree88013 жыл бұрын
Loving the content 👌
@MarioMartinez-os5ch3 жыл бұрын
Love your videos
@Tekniktools2 жыл бұрын
thanks your information
@tomking58223 жыл бұрын
Have rebuilt many over the years
@adnacraigo65903 жыл бұрын
Very interesting. Thanks.
@ghilreese34133 жыл бұрын
Thank You.
@stevenakn13 жыл бұрын
I had one go bad one time and it blew the hose. I replaced the gauge and tossed the old one. I always thought they could be rebuilt though👍
@mikep10853 жыл бұрын
Thats awesome! Any idea how old the gauge/regulator set is? They look pretty old... and well made!
@obfuscated3090 Жыл бұрын
That SR style body could be decades old or quite recent. SR stands for "Safety Regulator" as it improved on the older designs. They are still made because there really isn't any significant improvement on the new ones. An old is as good as new after rebuild which you can have done cheaply too online or via your local welding supply.
@aaronperysian94133 жыл бұрын
I like it thanks. Let’s see that dodge service truck!!!
@ICWeld3 жыл бұрын
Coming soon!
@jacobvargas94273 жыл бұрын
What Psi's do you generally have the regulators set to?.
@ICWeld3 жыл бұрын
7/70
@MrDillaKilla2 жыл бұрын
@@ICWeld running a #4 tip?
@codybrown51953 жыл бұрын
Torch rebuild would be cool also. I can lend you one if you want. LOL
@karlsalm90693 жыл бұрын
Thanks for knowledge
@Wingnut_Stickman3 жыл бұрын
A bit like taking a wristwatch apart. I assume the reason you didn't use the torch to cut the regulator open was the regulator was broke? Don't try that at home. Nice video, thanks for sharing.
@OutofTownwithRobinBell3 жыл бұрын
Thanks very use full 👍
@blinko6563 жыл бұрын
Evening therapy! :)
@SouthernGround10 ай бұрын
In the early 60's when my dad started up his welding shop he had a friend in the next town who helped him get started, old ED had been in business just after WW2 and Edward loved fixing all his equipment until one day he fixed his oxygen reg, then BOOM! Eddie's shop burnt to the ground and ED spent about six months in a burn center almost dieing three times from the effects. Edward wasn't careful and he wished he had died. the price of a reg ain't worth screwing around with them.
@leewelbanks63663 жыл бұрын
Unless you have oxygen cleaned tools and know what you are doing never mess with a high pressure regulator. One spec of a flammable material left in that regulator when you put it back together could be a bomb when you open the cylinder. Send your regulator in for rebuilt or get a new one. I retired from the industrial gas industry and have actually seen explosions for oxygen and oil.
@milotorres68943 жыл бұрын
So true of danger, clean room style..
@ke6gwf3 жыл бұрын
Yes, I was cringing watching skin oil fingerprints being left on the high pressure side.. Lol
@gracewthomas3 жыл бұрын
after you are done working/welding do you set your gauges / back them all the way off showing no pressure on the gauges ? Again always good info and technical help in all your videos , please more videos Alan Thomas
@obfuscated3090 Жыл бұрын
I'm of course not him but I usually don't. I shut off the cylinder then bleed down the hoses. After rebuilding many regulators I see no benefit to worrying over that since they're simple and robust. The only regs I rebuilt were bought used with intent to rebuild them. A rebuild can last decades on a reg. A torch could go a century and I have two Oxweld W-1s that old.
@maxmacdonald71743 жыл бұрын
The liability insurance is probably stupidly high on those regulators.
@LolPepperGate3 жыл бұрын
Cool video!
@lalitoojos2 жыл бұрын
Just curious. why no oil on oxygen?
@steveb61033 жыл бұрын
The lube is silicone based. Any oil based products is a explosion waiting to happen with compressed oxygen. I had to buy all new torches when I could no longer find parts for my Air Products setup.
@redpost23802 ай бұрын
Check again. Silicon oil is NOT safe. It ignites under pressurized oxygen like other lubricants
@skeeterbug9875 Жыл бұрын
Oxygen regulators require a minimum level of cleanliness, gloves, bagging, handling to be safe. Many items- including metals-burn explosively in the presence of contaminates, oils dust and high-pressure oxygen- especially when there are high-pressure pulses that occur when a valve is quickly opened. Ever see aluminum 6061 manifolds that burned and melt? Many years ago had to develop cleaning and handling procedures to keep our technicians from getting maimed on a DOD program. We spent several years dissecting many regulators and developing high flow, high speed pulse regulators for aural weapons noise simulators and . Sometimes being able to make a video can be dangerous to the folks that think it looks so easy and then they get hurt badly because they missed a tiny detail. Understand the the disclaimer in the beginning of the video that might help the trial -when stuff goes sideways- and little Ricky gets disfigured or the house burns down and you have to call the Allstate guy. Be safe and understand that there are bad things that infrequently occur in high-pressure oxygen gas systems.
@stevencorley23523 жыл бұрын
Oh yea. I dig it.
@69uremum3 жыл бұрын
That white washer is supposed to have a split.
@leso2043 жыл бұрын
How did all the dust & crap enter the gauge ........
@mhughes11603 жыл бұрын
I drop mine off at the welding supply store and in a week pick them up they look like new For $75 bucks. I used to do my own (but now that I can’t read that part # either )lol Its easier
@obfuscated3090 Жыл бұрын
LWS prices are very reasonable in many cases. If I have regs or torches I want polished I send those out since the price is the same either way.
@ezrhino18033 жыл бұрын
Awesome vid.
@pervasivemalaise3 жыл бұрын
there are oxygen compatible greases. follow the manufacturers recommendations and if you don't have the manufacturers information I would suggest you not overhaul the regulator. it is the stuff you don't know that will kill you and oxygen regulators have killed people.
@TheRitchieLeeShow3 жыл бұрын
I had a cheapo O2 regulator start spewing one day, about 20 years old. Just ordered a new one, of better quality. Glad it was not acetylene.
@bigunone3 жыл бұрын
Thanks I would have taken the long trip to town and dropped it off, then have to take the trip back to pick it up
@bigredracer78483 жыл бұрын
962👍's up IC WELD thanks for sharing
@fireynest72442 жыл бұрын
What’s the piece called that was broken
@Drew67093 жыл бұрын
Is the liquid Teflon suitable? As long as the liquid Teflon isn't overused.
@MrDillaKilla2 жыл бұрын
No.
@stanthurman90086 ай бұрын
15 years ago the the overhaul was 75.00: per gauge .
@OurnameisLegion663 жыл бұрын
Problem with 'stupid',there is no boundaries..
@dirtfarmer74723 жыл бұрын
Some comedian made the comment that stupid is Forever. Ron White
@Ham682293 жыл бұрын
This might be a silly question but, could you just make a new one from an old inner tube? I'm not sure about that white plastic one. Awesome video, never tore into one. Had one do the same, took it in, OMG, could've purchased a whole new torch kit for what they charged me. It was the Oxygen regulator as well. Great video as always, cheers :)
@obfuscated3090 Жыл бұрын
The only "silly" question is one you don't ask. The answer in this case is NO. kzbin.info/www/bejne/b3yylJmIqsiYnrc High pressure oxygen is dangerous when it contacts the wrong materials. Use only oxygen-safe cleaning procedures and correct factory parts or you can easily be injure or killed. Not joking. Use no oil.
@douglaspollock10210 ай бұрын
Others posted that it’s viton (fluorine rubber), so unless you’re inner tubes are made of that you shouldn’t. If you’re inner tube has petroleum products or another substance that reacts with high pressure oxygen it could go boom.
@jimsvideos72013 жыл бұрын
Wash your hands and your tools real well before you try this; compressed oxygen and anything flammable usually adds up to bad things.
@ke6gwf3 жыл бұрын
Yes, I was cringing watching skin oils get on the high pressure side... Lol
@leso2043 жыл бұрын
Oxygen is not in it's-self flamable ............
@ke6gwf3 жыл бұрын
@@leso204 yes, we know, but basically everything else IS flammable in the presence of high pressure oxygen, including metal.
@jackdawg45793 жыл бұрын
Yesterday I noticed that I have broken my second oxygen gauge in as many months... less than happy!
@jackking55673 жыл бұрын
Surprised the valve failed in a high pressure type of way! Could have been bad for hoses and the user.
@obfuscated3090 Жыл бұрын
No, the feature which ensures that does not happen is why Victor named that style the SR for safety regulator. The blowoff valve prevents overpressure when the high pressure seat fails as sooner or later any seat will. It's common for regs to last fifty years without failure they're so well made. Once overhauled they're good for another 50.
@4211welderman3 жыл бұрын
I feel you on the can’t see. A mean trick on us welders the older we get!!
@dbutler55843 жыл бұрын
Had to find my cheaters before I could watch the video! Yep, I’ve just “retired” the old set and bought new ones. Of course, people that build gages want jobs too-
@mattsirmans91463 жыл бұрын
Yep, I'm only 38 and can already tell my eyes ain't what they used to be after 20 years of welding.