With the regular plastic feet, I drive a 3/4 inch screw through the part that comes off so easily, through the base plate and slightly into the cabinet. Easy, quick and the feet do not come off when you move the cabinet around prior to attaching it to the wall.
@andrewkraus88022 жыл бұрын
This literally saved so much frustration. I snapped 12 of those junk legs before I found this video. THANK YOU SO MUCH!!!!!
@PetiteBluebirdgirl10 ай бұрын
There is always a better way kzbin.inforPgIAk8NdOc
@petemiller519 Жыл бұрын
Good video, thanks! I think I'll use hot glue for the filler. By the way the leg offset was 3 3/4" not 4 3/4" :)
@jonesconrad12 жыл бұрын
this is great thanks, I built a wooden plinth for most of the kitchen units to sit , but I will use this for the sink unit in case there is a spill.
@tb-xy7lg2 жыл бұрын
This is a great idea. You are right those legs were such a pain when I was installing the cabinets. I was pulling hair out. I ended up gorilla gluing the leg pieces in. No problems after that. I am about to do another kitchen in our rental and I'm going to try this way. Thanks!
@bhayescampbell Жыл бұрын
That was my thought. I already bought the SEKTION legs so why spend another $120 when gluing works? Though I would probably go with the CAPITA if I hadn’t bought SEKTION.
@HumanBean520 Жыл бұрын
Honestly who at IKEA thought it was a good idea to construct cabinet legs out of cheap grade plastic 🤦♂️
@benzun9600 Жыл бұрын
someone on drugs or an engineer
@wmwnwmn3 жыл бұрын
This helps a lot, great video man!
@Countdracula6 Жыл бұрын
Thank you for sharing this!
@saidmokhtari497 Жыл бұрын
Merci. Well done and explained.
@millieh.-nyc65372 жыл бұрын
Awesome fix! Thanks for sharing. Be well.
@postbeam82002 жыл бұрын
Thanks, you too!
@geoffmcrorie905 ай бұрын
I found when fitting those plastic legs,glue everything together,then with a helper turn the cabinet the right way up without letting the legs drag on the floor. Then position it into position, lift and lower without draging. Hope this helps.
@liquidcoffeeguy2 жыл бұрын
excellent IKEA hack .......👌👍
@PurgeGT Жыл бұрын
My concern would be that the Capita thread is pressure against a much smaller plastic threading, where the Sektion leg thread is much thicker (and I'm concerned more with load). I think I'll probably just glue the top of the leg into the plastic stand with the dowels. thanks for the video! :) Saved me buying a bunch of Capita stuff.
@nathaliehupe778 Жыл бұрын
Very Nice. Thank you
@ryanwilliams30063 жыл бұрын
You mean 3-3/4.
@postbeam82003 жыл бұрын
You are correct sir. 3 and ¾
@PaulLebow2 жыл бұрын
Great but I've had my Skeltion cabs in for 12 years with never an issue with feet coming loose. Maybe if one is moving the cabinet around but seems to work fine.
@nexuswoodwind Жыл бұрын
This was a life saver, as those plastic feet are impossible to work with. I went ahead and ordered the Capita feet and did exactly as you recommended. The only thing I did differently (instead of epoxy), was I cut some heavy duty GORILLA tape to a 10" length and wrapped around the bottom of the steal Capita foot, Then twisted the plastic part on. It held the black sleeve firmly in place with no wobble at all. Still- epoxy is a great idea and may hold up better in the long run.
@PetiteBluebirdgirl10 ай бұрын
You did not need to order any other feet. You could have used 14mm screws and screwed those into the actual plastic dowels. I have a video showing how. Takes a woman 😂
@culdesachero7 ай бұрын
This is a great idea because I don't like the plastic legs. However, the Capita feet have a lot less travel than the plastic ones. I'm having trouble leveling the side with the lower floor because the gap is slightly more than the max height of the Capita legs.😢
@NOLIFEWITHOUTMUSIC13 жыл бұрын
This helps out a lot! Thank you! Now I can get the capita legs and use the kick plate but I wonder if there is PVC pipe of the same dimensions to keep from having to buy 2 sets of legs for each base cabinet🤔
@postbeam82003 жыл бұрын
Let us know if there is a PVC size that fits... I have a hunch that they are using a metric size but it kinda looks close to 1"... who knows :)
@nikitaabrown2 жыл бұрын
I know it's been a year, but did you find a PVC pipe that fit?
@Auheye11 ай бұрын
I was thinking the same thing - but the hooks for the kickplates come with the plastic legs so you really are stuck buying them either way...
@mademoiselledusfonctionell16099 ай бұрын
You're supposed to put the feet between the cabinets, or, when you do not have room, at least under the side of the cabinet (the "wall" of the cabinet if you will) to support the cabinet structure.
@mattelliott2940 Жыл бұрын
Thanks! What epoxy adhesive did you use specifically?
@kathyhuebner68511 ай бұрын
Great thanks
@ellipses872 жыл бұрын
I had the same idea but couldn't get the caps off the capita legs - your video gave me hope, and I got 2 off so far, out of 8. Any tips? I cracked the trim on one trying to force it :(
@bhayescampbell Жыл бұрын
Cut the SEKTION cylinder in half and glue it to the front of the CAPITA leg.
@quarterarcade88253 жыл бұрын
Dude - This is awesome. I was winching when I saw how cheap the default feet design is. This is a great hack. I am totally doing it. I am a noob, what 2-part epoxy do you recommend for filling the gap?
@postbeam82003 жыл бұрын
Hey thanks, Cool dog on your photo... So I am actually just using a Hot Glue gun now, the 2-part epoxy was totally overkill. All your really doing is keeping the little black cylinder from spinning or falling off the top ring of the stainless steel foot. It isn't holding any weight or any structure. I defiantly recommend a full sized glue gun not the little mini guns cuz it takes a lot of glue. Actually the glue gun is becoming like my favorite tool. Good luck!
@Pure3nrg2 жыл бұрын
Great way to think outside the box
@postbeam82002 жыл бұрын
Great way to keep the box from falling down :) Thank you!
@dash1dash24 ай бұрын
the plastic legs are fine, they're not designed for you to move the cabinets sideways or to slide them around. They're designed for downwards force, not side force (which should never happen anyway).
@jantelopez56262 жыл бұрын
is it possible to install extra feet when the cabinet is installed and upright? ours only has 4 for a double cabinet
@postbeam82002 жыл бұрын
I imagine it is possible to add extra feet after it is upright. The good news about the Capita feet is that they can be expanded under the cabinet (by spinning the leg) until they are the correct length, then all you need to do is install the screws to secure them. You might need a right angle attachment to allow you to screw in the 4 screws with an impact driver as it won't fit underneath. It's tricky but doable. Good luck!
@benzun9600 Жыл бұрын
great fix. I hate those cheap Ikea feet. They really need to make metal standard for the feet.
@kristenmacf2 жыл бұрын
Ok so what can I do if the cabinets are already installed with the capita legs ? I can’t get the toe kick on
@postbeam82002 жыл бұрын
Hmmm..... You might be able to cut the SECTON plastic into two half pipes and then glue the two halfs onto your existing legs with a glue gun. That would give you the thickness to get the Ikea Section toe kick clips to fit. but yeah that's a tough one.... hope it works out :)
@TheHamster4430 Жыл бұрын
You could have used magnets glued to the kickplates with some wooden spasers
@mikehorton61953 жыл бұрын
IKEA should have dealt with this problem at the set. If they did they would sell a heck of a lot more product.
@postbeam82003 жыл бұрын
I know.... Ikea is Swedish for where Cash meets Trash. Some of their stuff is amazing like the Blum hinges and hardware and some is garbage like the plastic feet.
@afriendlyguy1 Жыл бұрын
You should install the legs so that they support the sides. In the IKEA system the loads are transferred through the cabinet sides (legs and wall clips). The placement of your legs, inset from the edges, doesn't maintain this important structural condition.
@AidanSkoyles Жыл бұрын
agree. you're on to something here....
@china1984able Жыл бұрын
Incredible IKEA still sells the plastic garbage. By the way for the Metod cabinets you need the shortest Capita because the Metod is higher (80 cm) than the previous model (70cm).
@goldringsify2 жыл бұрын
😲🤗
@TsiTsiLP Жыл бұрын
Yup. Those things ARE garbage. Now they are broken AFTER the counters are already installed. Any ideas? Hard to drill-in new feet feet with counters already installed.
@gregorywootton3870 Жыл бұрын
Plastic libs work great, user problem
@ferencujvari107111 ай бұрын
IKEA is goooood.....but the human brain is better!
@mikiex3 жыл бұрын
Another option - 3D print new clips? :)
@postbeam82003 жыл бұрын
That would be awesome! Wish I knew how to do that or had the 3D printer. What printer do you recommend?
@mikiex3 жыл бұрын
@@postbeam8200 "Ender 3 V2" for the printer and "Fusion 360" to design the part (There is a free license for hobbyists). I got one recently and really impressed.